磨料有序排布电镀砂轮的制备及其把持力研究

为解决电镀砂轮磨削加工中容屑空间不足的问题，采用点胶微粘接的方法制备了磨料有序排布的电镀砂轮，分析了磨料粘接效果和镀层力学性能。通过SEM分析了磨料/镀层/导电胶的结合界面，并进行了干磨削试验。研究结果表明，直径约为磨料粒径40%的胶点可粘接住磨料，单个胶点上粘接多颗磨料的占比小于6%；双脉冲电镀工艺制备的镀层显微硬度大于500HV，表层残余应力小于100MPa，磨料/镀层/导电胶之间的界面贴合紧密，无明显缺陷；砂轮在磨削时没有出现磨料脱落现象。     

Study on the non-uniform contact during ELID groove grinding

This paper introduces the potential feasibility that ELID (electrolytic in-process dressing) grinding replaces superfinishing in bearing manufacturing, but ELID grinding will bring new challenges. Different regions present distinguish surface profile due to the non-uniform contact in ELID groove grinding. However, few reports explaining the non-uniform contact are available. This article explores the mechanisms of the non-uniform contact during ELID groove grinding. Experiments on the non-uniform contact between bearing raceway and grinding wheel have been carried out under different conditions. The results show that non-uniform contact exists in ELID groove grinding process and it exerts influence on the profile of the raceway surface. Non-uniform contact influences the Rsk and Rku value all the time, but it influences the Ra value occasionally. Improvement strategies of eliminating the non-uniform contact are also discussed based on the experimental study.     

可调偏迈步式胶带自移机尾的研究

随着掘进工作面自动化程度的提高,掘进巷道速度也在日益加快,而现有的顺槽皮带机机尾移动缓慢且移动时工作量大,需要两三人配合操作,存在一定的安全隐患。针对以上问题,研发可调偏迈步式胶带自移机尾,具有与悬挂二运皮带转载机搭接行程长,可以迈步式前进,自动调偏等功能,同时,可以降低工人的劳动强度,加快巷道掘进速度。     

皮带秤秤架的响应特性曲线分析

介绍了皮带秤秤架响应特性曲线分析方法，对四种结构形式的秤架进行了响应特性曲线分析和比较，得出的结论是：悬浮式秤架的计量特性最好。     

Methods of Verifying Continuous Automatic Belt Weighers: State and Prospects

The basic methods of verifying continuous automatic belt weighers are described. A comparative analysis of these methods on the basis of experimental studies is made and ways of implementing the results in industry are recommended.     

浅谈延迟焦化装置露天栈桥的设计

根据延迟焦化装置露天栈桥的工程设计实践,围绕一炉两塔(一个加热炉两个焦炭塔)的焦化装置,分析了露天栈桥设计中的要点及难点,对其在平面布置、基础安排和吊车梁选型等设计方面做一些介绍和论述。     

长距离钢带传动的张紧机构设计与应用

比较了几种长距离传动方式的特点与适用场合，重点探讨了实现长距离精密传动的技术要点。结合实际工程，完成了长距离钢带精密传动的应用，并指出张紧机构的设计与应用是钢带实现长距离精密传动的关键。为此文中对钢带传动的典型张紧机构进行了比较，并分析了这几类张紧机构的应用情况，有参考和应用价值。     

用于机器人轨迹定位纠正系统的回声状态神经网络研究

循环神经网络(RecurrentNeuralNetworks)是人工神经网络(ArtificialNeuralNetworks)中重要的分支,与前馈神经网络(ForwardNeuralNetworks)相比具有更好的时间序列学习能力。但长期以来其学习法一直不能脱离前馈神经网络而自成一体,回声状态神经网络(EchoStateNetworks(ESN))是打破这一局面的全新学习方法。其独特的结构,良好的短期记忆能力,方便的学习方法,不俗的非线性特性是以前循环神经网络所不可比的。本文在介绍了回声状态神经网络之后将其用于四轮机器人的位置测量系统中,有良好的表现。     

Simulation of Strength Distribution in Ground Ceramics by Incorporating Residual Stress Effect

Strength of ground ceramics may be affected by residual stress as well as surface flaws induced by grinding. Strength prediction for ground ceramics is convenient for mechanical design of ceramic components. In this article, a numerical procedure based on fracture mechanics was proposed to estimate strength distribution of ground ceramics by considering grinding-induced residual stress. Bending strength and residual stress of ground ceramics were measured for three grinding-conditions. By comparison of simulated results with experimental ones, it was revealed that strength characteristics in experiments were well simulated by using the proposed procedure.     

煤炭码头带式输送机控制系统

介绍煤炭码头带式输送机联锁控制系统设计的一种方法，详细阐述了整个系统的工艺流程、启动方式以及控制原理等。这种方法可以实现带式输送机远程中控室控制，也可进行就地带式输送机机侧控制。