Stress-strain relations in elastoplastic solids with Dugdale-type cracks

Mechanical behavior of a two-dimensional elastoplastic solid with rectilinear cracks is investigated. Plastic strip model is used to reduce plasticity problem to the equivalent linear elasticity formulation. Two realizations of the mixed mode plastic strip model are considered: in-line plastic strips as proposed by Becker and Gross [Int. J. Fract. 37 (1988) 163], and inclined plastic strips of Panasyuk and Savruk [Appl. Mech. Rev. 47 (1994) 151]. The effective mechanical response predictions are based on the procedure presented in Kachanov et al., [Appl. Mech. Rev. 47 (1994) 151]. Stress-strain relations are obtained for parallel and randomly oriented non-interacting cracks. Results are compared with known elastic solutions.     

激光熔覆专用铁基合金粉末的研究进展

指出了目前防止熔覆层开裂所采取的主要措施中存在的问题,阐述了激光熔覆和热喷涂对于所用合金粉末性能要求之异同,评述了激光熔覆专用铁基合金粉末的研制现状,提出了成分与组织设计的新思想。     

激光熔覆Ni基SiC合金涂层组织与性能的研究

利用5kWCO2连续波激光器在16Mn钢基材表面对含20%(体积比)SiC陶瓷粉末的镍基自熔性合金粉末进行激光熔覆得到Ni基SiC合金涂层(NiSiC)。研究了合金涂层的组织形貌及相结构,并用单纯的镍基合金涂层(Ni60)进行了显微硬度及滑动磨损性能的对比试验。结果表明,NiSiC合金涂层由γ枝晶及其间的共晶组织组成,主要组成相为γ-Ni,γ-(Ni,Fe)固溶体和(Cr,Fe)7C3,Cr23C6及(Cr,Si)3Ni3Si等化合物。添加SiC的镍基合金涂层NiSiC比单纯的镍基合金涂层Ni60具有较高的硬度和耐磨性。     

焊接波浪状边缘薄钢带的高上山成型法

介绍了高上山成型法的工艺特点及理论上的可行性和实践中的可靠性，此方法能有效地解决薄钢带波浪状边缘的焊接方面存在的问题。     

Recrystallization/precipitation behaviour in microalloyed steels

Microalloyed high-strength low-alloy (HSLA) steels contain additions of Nb, V, Ti, or in combination, in amounts of 0.01 to 0.1 weight percent to improve mechanical properties, which are strongly dependent on the thermomechanical interaction taking place in the course of rolling mill processes. The recrystallizatian of hat-twisted austenite has been investigated in a cylindrical specimen (f 6×50 mm) machined from hat rolled plates of 0,052 wt % Niobium microalloyed steel. Continuous and interrupted torsion test were carried out in the temperature range 1123 K to 1173 K after a solution treatment of 1.5 minutes at 1423 K and torque-twist data were analysed. The various methods were discussed for obtaining results from torsion tests. The effect of precipitation kinetics was appreciated by way of connection t_p/t_p(red), where t_p is the experimental measured time for the peak stress and t_p(red) is the newly defined reduced time. The softening ratio X and time t_0.05R for start of static recrystallization were established.

The correlation between precipitation and recrystallization is presented as a graphs for chosen requirements (temperature of austenitization, carbon and niobium content and strain rate). If temperature goes below 850°C, the restoration processes are hardly suppressed, both are limited by diffusion and Nb(CN) precipitation, which are extended dynamically in the range of strains rates 10⁻² to 1 s⁻¹.

In the present paper, an attempt is made to derive the PRTT diagram and to define all mathematical equations for describing recrystallization times t_0.05R, t_0.5R, t_0.95R and t_0.05P for the start of precipitation. In real metal forming processes such as the hot rolling of plates or strips the knowledge of these parameters and results is extremely important for the the correct microstructure and sheet quality to be obtained.     

钢带捆扎对木箱强度的影响

从力学角度分析了钢带捆扎对木箱强度的影响，指出木箱经钢带捆扎后，可减小箱底的最大弯矩，提高木箱的承载能力和减少板厚。同时还在无支撑间隔的基础上，详细介绍了钢带捆扎的设计方法。     

唐山建龙900mm冷轧机组的工艺与设备

较系统地介绍了我国第1条国产化的中宽带钢冷连轧生产线，即唐山建龙钢铁控股有限公司900mm冷连轧生产线的工艺流程、主要设备组成及技术特点。重点介绍了900mm 4机架六辊轧机的技术参数、性能特点及自动控制系统。该生产线投产以来，取得了较好效果。     

双辊薄带钢连铸在线自动检测系统

介绍了双辊薄带钢连铸工艺,设计了双辊连铸机的计算机在线自动检测系统,通过采取正确的抗干扰措施提高了检测的精度,系统在双辊薄带钢连铸试验中应用效果良好.     

热轧高强钢平整机辊径参数设计技术研究

基于高强钢平整机的生产工艺特点,结合板形与辊耗问题,将带材的出口前张力与辊间压力横向分布都均匀作为目标函数,把保证所有被平整高强钢产品的机械性能满足产品大纲要求作为约束条件,提出了一套针对热轧高强钢平整机的工作辊与支承辊辊径参数设计模型.其研究结果对指导宝钢分公司1880 mm热轧平整机的工艺参数的确定与技术谈判发挥了重要作用,并具有进一步的推广价值.     

推拉式浅槽盐酸酸洗工艺的操作经验

介绍了带钢推拉式浅槽紊流盐酸酸洗各工序的操作经验,并提出了建议。