Effects of Winding Attachment Positions on Output Characteristics of Flux‐Modulating Synchronous Machines

The flux‐modulating synchronous machine (FMSM) is a new type of multipole SM with nonoverlapping concentrated armature and field windings on the stator. This paper compares the output characteristics of two FMSMs through finite element analysis (FEA) and experiments. In both of the FMSMs, the attachment positions of the armature and field windings are swapped. To determine the reason for the discrepancies in their output characteristics, unsaturated inductances were calculated using a d‐‐q equivalent circuit. In addition, the calculated results of the inductances were confirmed through a visualization of the leakage fluxes using FEA. The results of the study show that the synchronous inductance can be reduced by attaching the armature winding to the air‐gap side of the stator teeth and that the reduction leads to an increase in output power.     

Designed damping controller for SSSC to improve stability of a hybrid offshore wind farms considering time delay

This paper presents the stability improvement results of hybrid doubly fed induction generator (DFIG)-based and permanent magnet generator (PMG)-based offshore wind farms (OWFs) using a static synchronous series compensator (SSSC). An adaptive-network-based fuzzy inference system (ANFIS) controller of the proposed SSSC is designed to render adequate damping characteristics to the studied system. A frequency-domain approach based on a linearized system model using eigenvalue technique analysis is performed. A time-domain scheme based on a nonlinear system model subject to a three-phase short circuit fault at infinite bus with variations in the signal transmission delays has also been investigated to compare the damping of the studied system in cases of with and without controller. The simulation results with MATLAB/SIMULINK toolbox have been presented. It can be concluded from the simulation results that the proposed SSSC joined with the designed ANFIS damping controller can offer adequate damping performance to the studied hybrid DFIG-based and PMG-based OWFs under severe disturbance.     

Robust Control of Permanent Magnet Synchronous Motors

In this paper, permanent magnet synchronous motors (PMSMs) are investigated. According to the feature of PMSMs, a novel state equation of PMSMs is obtained by choosing suitable state variables. Based on the state equation, robust controllers are designed via interval matrix and PI control idea. In terms of bilinear matrix inequations, sufficient conditions for the existence of the robust controller are derived. In order to reduce the conservation and the dependence on parameter, the control inputs of PMSMs are divided into two parts, a feedforward control input and a feedback control input, and relevant sufficient conditions for the existence of the controller are obtained. Because of the suitable choice of state variables, the proposed control strategies can cope with the load uncertainty and have robustness for disturbance. Finally, simulations are carried out via Matlab/Simulink soft to verify the effectiveness of the proposed control strategies. The performance of the proposed control strategies are demonstrated by the simulation results.      

基于DSP的多元数据同步采集与存储系统的设计与实现

从硬件和软件两个角度出发,介绍基于DSP的多元数据同步采集与存储系统的组成、工作模式以及功能的测试。系统主要由上位机和数字采集与存储单元组成,其中数字采集与存储单元的硬件部分包括电源模块,值班电路模块,数据采集模块,数据存储模块,时钟同步模块。系统采用DSP作为中央处理芯片,利用经过同步后的秒脉冲作为触发信号,实现同步数据采集。以CF卡作为存储介质,实现数据自容式存储。软件部分实现自检、同步、数据采集存储功能。经过测试,系统工作稳定,功能正常,同步精度在100ns以内。     

葛洲坝水利枢纽泄水建筑物进水口冲磨与修复

葛洲坝水利枢纽工程已运行20余年，近年水下检查中发现泄水建筑物进水口存在不同程度的冲磨，有些已威胁到建筑物安全运行，分析冲磨原因和探讨修复材料和手段是非常重要的，本文就此问题提出一些看法和建议供参考。     

轻质滤料滤池的试验与研究

轻质滤料滤池是以比水密度略小的滤料为滤床的滤池，通过以净水厂的原水和污水处理厂的二级处理出水为过滤试验对象，所取得的结果表明：下向流轻质滤料滤池对浊度和悬浮固体（SS）的去除率分别可以达到80％和45％，而滤床的水头损失不超过15cm。因此轻质滤料滤池可以以预过滤的形式配置在过滤处理的净水和污水的处理工艺中。     

直线电机抽油机与游梁式抽油机性能对比

攻克了直线电机大推力的关键技术,研制成功了具有国际领先水平的直线电机抽油机。这种抽油机最大特点是改变了过去各种抽油机将电能转变为旋转运动,再通过机械方式转变为直线往复运动的方式,通过变频和控制直接将电能转变为直线往复运动。与游梁式抽油机相比,直线电机抽油机不但提高了机械效率,而且能够实现抽汲参数的无级调整,进而能够根据抽油的需要调整悬点运动规律,具备智能化控制和远程监控的有利条件。     

超宽带极窄脉冲设计与产生

超宽带(UWB)技术是以持续时间极短的脉冲作为传输载体进行数据通信的无线新技术。基于BJT雪崩特性,本文采用并行同时触发的工作方式,设计并产生了高重复速率的UWB脉冲电路发生器,极大地减少了时延,缩短了上升时间,提高了脉冲的幅度,并从等效电路法的观点分析计算了脉冲的特性参数,理论结果与实测结果具有较好的一致性。     

换热器小浮头螺栓断裂失效分析

针对换热器小浮头螺栓发生断裂的情况进行失效分析，找出原因，提出处理措施及材质选择时应注意的问题。