Electrochemical mass transfer between an impinging jet and a rotating disk in a confined system

This paper presents the mass transfer results from an impinging liquid jet to a rotating disk. The mass transfer coefficients were measured using the electrochemical limiting diffusion current technique (ELDCT). Rotational Reynolds number (Re_r) in the range of 3.4 × 10⁴–1.2 × 10⁵, jet Reynolds number (Re_j) 1.7 × 10⁴–5.3 × 10⁴ and non-dimensional jet-to-disk spacing (H/d) 2–8 were taken into consideration as parameters. It was found that the jet impingement resulted in a substantial enhancement in the mass transfer compared to the case of the rotating disk without jet.     

Connecting the second exhaust-heat boiler to the operating first one under the conditions of flow circuits of combined-cycle plants with two gas-turbine units and one steam turbine

Problems arising with connecting the second exhaust-heat boiler to the first exhaust-heat boiler under load in the case of flow circuits of combined-cycle plants of type PGU-450 are considered. Similar problems exist for two-boiler single-turbine units of type PGU-325 and for two-boiler single-turbine units of traditional steampower plants with an output of 200–300 MW upon connection of the second furnace of a two-furnace boiler to the operating first furnace. Analysis of the temperature-induced stressed state and of the cyclic strength of thick-walled elements of the steam-water conduit of PGU-450 and of two-furnace boilers of two-boiler single-turbine units with an output of 200–300 MW (the check valve, the inlet header of the water economizer) is used for determining the steam temperature differences in the high-pressure conduits to the steam turbine and the order of connection of the second exhaust-heat boiler to the operating fist one. Modes of enabling a two-boiler single-turbine unit of a combined-cycle plant, which are most “rigid” from the standpoint of thermal strength, are determined. __________ Translated from élektricheskie Stantsii, No. 2, February 2006, pp. 11–17.     

Midplane-symmetry breaking in the flow between two counter-rotating disks

This paper considers the axisymmetric steady flow driven by exact counter rotation of two co-axial disks of finite radius. At the edges of the rotating disks one of three conditions is (typically) imposed: (i) zero velocity, corresponding to a stationary, impermeable, cylindrical shroud (ii) zero normal velocity and zero tangential fluid traction, corresponding to a (confined) free surface and (iii) an edge constraint that is consistent with a similarity solution of von Kármán form. The similarity solution is valid in an infinite geometry and possesses a pitchfork bifurcation that breaks the midplane symmetry at a critical Reynolds number. In this paper, similar bifurcations of the global (finite-domain) flow are sought and comparisons are made between the resulting bifurcation structure and that found for the similarity solution. The aim is to assess the validity of the nonlinear similarity solutions in finite domains and to explore the sensitivity of the solution structure to edge conditions that are implicitly neglected when assuming a self-similar flow. It is found that, whilst the symmetric similarity solution can be quantitatively useful for a range of boundary conditions, the bifurcated structure of the finite-domain flow is rather different for each boundary condition and bears little resemblance to the self-similar flow.     

改善磁盘阵列性能的方法

磁盘阵列是解决计算机Ｉ／Ｏ瓶颈问题的有效方法之一，通过对现有磁盘阵列结构的研究，提出了４种改善磁盘阵列性能的方法，即良分利用磁盘带宽，平衡多盘的负载，减少奇偶检验数据存取时间和磁盘阵列Ｃａｃｈｅ技术等，分析结果表明：在事务处理应用领域，利用Ｃａｃｈｅ来把小写转化为大写可大大改善目前一般情况下，以一道数据大小来作为磁盘的基本存取大小是合适的选择，磁盘阵列负载平衡设计不足是指正常模式下系统请求在多盘间     

凸轮机构基圆半径的确定方法及其分析

基圆半径的确定方法，除了用图解法和试算法外，还可用解析法和图解分析法求解。４种方法各有优缺点，设计时要根据具体情况选择。     

某型杀伤枪榴弹引信弹道炸原因分析及再设计思考

通过对某型杀伤枪榴弹引信所发生的三次弹道炸的原因进行分析，提出用延期索替代延期药盘，并对有关机构进行再设计的对策。     

蝶阀加工及装配工艺的研究

传统工艺加工阀体、活门时，对机床的性能要求较高，一般为数控镗床。介绍了一种采用普通镗床加工阀体、活门的工艺方法及蝶阀在厂内装配的工艺方法。     

A study on UV-curable coatings for HD-DVD: Primer and top coats

This study relates to the development of coatings for optical discs in high-density digital versatile disc systems (HD-DVD or blue lay disk) that use a high numerical aperture of 0.85 at 405 nm wavelength and have a protective top layer over a primer layer for protection against damage and dust. Ultraviolet-curable raw materials of two acrylic monofunctional monomers ( isobornylacrylate, IBA and tetrahydrofurfurylacrylate, THFA) and two kinds of urethaneacrylate oligomers (OUMD and OUME) have been easily mixed with photoinitiators. Curing rate of these materials was characterized by FT-IR. In case of top coats, VTES (vinyltriethoxysilane) and acrylic acid were added to enhance the abrasion resistance. These two kinds of UV-curable resinous materials having no solvent were synthesized and investigated as means for making a blue ray disk having good optical and mechanical properties. In addition, dynamic characteristics including reflectivity, fluctuation of RF signal and noise level were also investigated.     

ABB变频器在双馈发电机试验台上的应用

本文介绍了风力发电系统目前存在的技术方案，重点介绍了ABB用于双馈式风力发电系统的变频产品ACS800—67的特性，并对由其构建的发电机测试平台的案例进行了实验分析。     

汽轮机回热系统给水焓升的最优分配

从汽轮机回热系统的实际情况出发，运用非线性规划理论和计算机技术，解决了给水焓升设计中的最优分配问题。结合具体实例，针对国产200MW汽轮机回热系统给水焓升的分配进行了说明。