Effect of spheroidized microstructure on the impact toughness and electrochemical performance of a high-carbon steel

The influence of cementite spheroidization on the impact toughness and electrochemical properties of a high-carbon steel has been thoroughly investigated in this study. Heavy warm rolling, followed by 2 h of annealing, has resulted in near-complete spheroidization, leading to a microstructure consisting of nano-cementite globules dispersed in the ultrafine-grained ferritic matrix. The Charpy impact test exhibited superior impact toughness with increased spheroidization. It is validated by the presence of abundant dimples in the fractographs of spheroidized specimens, in contrast to the as-received one that experienced a brittle failure due to its lamellar pearlitic structure. Potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) carried out in a 3.5% NaCl solution revealed that the corrosion resistance of the alloy gets improved with the increase in the degree of spheroidization. This is attributed to the lower susceptibility of the spheroidized specimen to microgalvanic corrosion owing to the minimum area of contact between nano-spheroidized cementite and ferrite, as elucidated with the help of EIS results aided by equivalent electrical circuit model.     

5A06-O aluminium–magnesium alloy sheet warm hydroforming and optimization of process parameters

The uniaxial tensile test of the 5A06-O aluminium–magnesium (Al–Mg) alloy sheet was performed in the temperature range of 20–300 °C to obtain the true stress–true strain curves at different temperatures and strain rates. The constitutive model of 5A06-O Al–Mg alloy sheet with the temperature range from 150 to 300°C was established. Based on the test results, a unique finite element simulation platform for warm hydroforming of 5A06-O Al–Mg alloy was set up using the general finite element software MSC.Marc to simulate warm hydroforming of classic specimen, and a coupled thermo-mechanical finite element model for warm hydroforming of cylindrical cup was built up. Combined with the experiment, the influence of the temperature field distribution and loading conditions on the sheet formability was studied. The results show that the non-isothermal temperature distribution conditions can significantly improve the forming performance of the material. As the temperature increases, the impact of the punching speed on the forming becomes particularly obvious; the optimal values of the fluid pressure and blank holder force required for forming are reduced.     

浅析HPT250轧机中滑移系数对轧制过程的影响

通过HPT250轧机在技术改造中遇到的一个问题，即滑移系数对冷轧元缝钢管在轧制过程中所起的作用。在实际生产中经过不断的技术研究和改进。使闲置多年的HPT250轧机为钢管公司的生产迭拉起到很大的作用。     

大型连杆流线简易试验方法

介绍了一种大型连杆流线的简易试验方法及其评价原则。该方法可清晰显示流线，并适合任何尺寸和形状的锻造连杆的流线试验。     

GJB712A-2001航天用GH4169高温合金锻制圆饼规范介绍

介绍了GH 4 16 9高温合金锻制圆饼规范的修订内容 ,对其主要技术指标作了简要说明 ,并与国外同类标准进行了比较。     

河北冶金实验厂8MN快锻液压机电控系统选择

着重阐述了河北冶金实验厂８ＭＮ快锻液压机电控系统的选择过程。经过反复考察，论证，对比，最终所选的压机电控系统为目前国产快锻液压机中自动化水平最高的锻造设备。     

台阶轴自由锻造工艺的计算模型

台阶轴是一类复杂锻件，合理的工艺计算模型是提高工艺设计水平的关键。本文提出三段式于模型以及虚拟轴节方法可以概括各种台阶轴，在此基础上可采用现代计算机及计算机优化技术，自动编制出最优的锻造工艺方案。     

-50℃用20MnMoD钢锻件及其焊接接头性能

研究了-50℃的20MnMoD钢锻件及其焊接接头在不同热处理状态时的综合力学性能。结果表明,-50℃的20MnMoD钢锻件具有良好的低温韧性,可与-50℃级正火型低温压力容器钢15MnNiNbDR配套使用。     

就拉杆固定支架谈锻件的缺陷分析

针对汽车锻件拉杆固定支架在生产过程中产生的裂纹、折叠、表面脱碳等多种形式缺陷,从锻件生产工艺过程的各工序来分析其可能产生的缺陷,并重点就裂纹、折叠、表面脱碳等缺陷产生的原因及其解决方法进行探讨,从而进一步完善生产工艺,改善锻件质量.     

低碳钢热变形过程中铁素体的织构形成规律

利用背散射电子衍射取向成像技术定量分析了热模拟单向压缩条件下Q235碳素钢热变形时铁素体的织构形成规律。结果表明,在710℃纯铁素体热压缩过程中,形成〈100〉和〈111〉方向的线织构。〈111〉方向织构增强的速度较快,到应变为1.0时达最大值,然后随应变的加大而减弱;〈100〉方向织构在形变量较小时增强的速度较慢,在大应变时增强的速度很快。大应变时虽导致一定程度的动态再结晶,使铁素体晶粒细化,但组织不均匀,织构过强,造成强烈的各向异性。在奥氏体与铁素体两相区变形时,先共析铁素体因形变同样产生强烈的织构。随着形变温度的提高和先共析铁素体的减少,织构减弱。