无油润滑压缩机活塞环和支承环设计

通过对填充聚四氟乙烯材料活塞环及带卸荷槽结构支承环的研究 ,确定了活塞及活塞环结构 ,建立了带卸荷槽支承环的力学分析模型 ,并将其结果用于结构尺寸的确定。在压缩机工艺指标不变的情况下 ,用该方法设计的活塞环和支承环性能优良。     

无掩模激光干涉光刻技术研究

介绍了一种不用掩模的光刻技术———激光干涉光刻技术的基本原理,给出了干涉光刻技术的主要特点及一些可能的应用,并对实验系统和初步实验结果进行了分析。研究表明,激光干涉光刻具有大视场和分辨率高和视场宽等优点。     

Influence of Edible Films upon the Moisture Loss and Microstructure of Dietetic Sucrose-Free Sponge Cakes during Storage

The kinetics of changes in the bound water content in dietetic sucrose-free sponge cakes (DC) during storage was investigated. The effect of edible films of polymyxan, pectin, xanthan, and carboxymethylcellulose upon this kinetics was also investigated. The quantitative changes in both states of water (slightly bound water and strongly bound water) were registered by combined dynamic analysis (thermogravimetry analysis, TGA, and differential thermal analysis, DTA). The moisture changes in DC crumb were analyzed by drying out to constant mass. The rate constants were determined according the equation q = q_oe^-kt. The values of rate constants 'k', in day^-1, concerning the different edible films were as follows: for crumb moisture is (8.00 ≤ k ≤ 12.47) × 10^-3, for bound water is (3.07 ≤ k_w ≤ 6.26) × 10^-2, for slightly bound water is (4.22 ≤ k₁ ≤ 8.49) × 10^-2 and for strongly bound water is (2.02 ≤ k₂ ≤ 5.62) × 10^-2 as compared to 18.53 × 10^-3, 7.16 × 10^-2, 9.04 × 10^-2, and 5.36 × 10^-2 in the uncovered DC, respectively. The best water-retaining effect in respect to crumb moisture during storage was ascertained in the use of polymyxan and xanthan films. The lowest rate constant values for bound water and its two states were measured for DC covered with pectin. The relation between the kinetics of both bound water states during storage and ageing of the crumb of DC covered with different edible films and the crumb microstructure was represented. By means of scanning electron microscope was read the smallest change in crumb microstructure of pectin-covered DC on the sixth day of storage.     

提高超小型铝电解电容器生产一次合格率

恰当选择原材料、确保铆接工序质量、重视工作电解液的配比、严控各工序成品率是提高超小型铝电解电容器投入产出一次合格率的关键。以１０Ｖ－４７μＦ（４ｍｍ×７ｍｍ）产品为例，投入产出一次合格率达９４％以上。     

无粘结预应力蛋形消化池的施工技术

石家庄市桥东污水处理厂有6座11500m3无粘结预应力混凝土蛋形消化池,本文介绍其非预应力钢筋、模板体系、混凝土和预应力工程等结构施工成套技术。     

开放的ladder型无反转激光系统的稳定性分析

利用开放的ladder型无反转激光系统的密度矩阵运动方程组的定态解和激光场运动方程分析了系统的稳定性。结果表明：如果增益大于激光腔损耗，则零解是不稳定的；如果增益小于激光腔损耗，则零解是稳定的；如果增益大于激光腔损耗，则非零解是稳定的。     

埋地管道三层PE外覆盖层及其检测方法研究

文章介绍了埋地管道三层PE外覆盖层系统的构造参数和性能特点,论述了两种用于埋地钢质管道外覆盖层状况检测的方法,一种是多频管中电流法,另一种是DCVG/CIPS组合检测技术。分别介绍了两种方法的工作原理、操作方法和设备,并结合工程实例进行了说明。这些方法和设备可分别或同时用于管道不开挖检测防腐层破损点的位置以及漏点大小。     

双层堤基的井涌破坏与无害管涌

双层堤基水文地质结构特殊，堤基承压水常具独特的“渗而不流”特征。在“不流”条件下，堤后盖层薄弱处受超高承压水头顶裂破坏，产生的局部冒水孔实属承压自流井，由此形成的管涌实质为井涌。底部进水的承压井流影响范围不大，井涌的破坏范围更小，据此可区分出有害管涌与无害管涌。前者局限于堤脚附近，小范围压渗为首选方案；对后者，既无需专门防治，更不必追求根治。     

非平面对称磁场的空间展开及样条函数表述

为了研究带电粒子光学系统的光学特性,需要知道系统中磁场的空间分布。实际磁场往往不具有严格的平面对称性质,一些作者曾就这类磁场的空间展开做过不少工作。但他们的工作是在柱坐标系统中进行的,适用于诸如回旋加速器、双向聚焦磁分析器、环形磁β谱仪等一类装置的磁场分析。对于大型同位素电磁分离器(calutron)那样一类装置,其磁场分布需要     

中山包水电站钢岔管设计

中山包水电站钢岔管在天生桥二级水电站 6号压力钢管下平段分岔 ,岔管HD值达 15 40m2 ,结构体形复杂 ,采用NK HITEN780A Z35和NK HITEN6 90B高强度钢材制造安装 ,在国内水电工程中实际应用较少。文章着重介绍岔管的布置、结构分析和焊缝的无损检验要求。中山包水电站的正常发电运行 ,为 80kg/mm2 级高强钢在国内水电行业的应用提供了第 3个成功实例