东兴铝业嘉峪关分公司铝灰渣循环利用研究

铝灰渣是铝熔铸过程中产生的废弃物。本文主要介绍了酒钢东兴铝业嘉峪关分公司铝灰渣的产生量、排放、利用情况、化学成分及表面特征,并简要介绍了铝灰渣、铝灰的循环利用途径。     

四川盆地上三叠统划分对比研究

四川盆地上三叠统对比长期存在混乱，给盆地整体评价带来困难。通过岩石地层、地震地层、事件地层及高分辨率旋回地层等多种方法讨论了须家河组与香溪群各岩性段的对比关系，得出了全盆地上三叠统的对比关系；指出须四段底可近似看成等时界面；须家河组下部地层自西向东、向南逐层超覆在雷口坡组之上，上部地层在盆地西北部自东南向西北方向剥蚀层位渐次变老。文章建议四川盆地上三叠统废除“香溪群”，统一使用“须家河组”，以利于对全盆地上三叠统进行油气资源整体评价与深化研究。     

Electrochemical synthesis and characterization of chloride doped polyaniline

Chloride doped polyaniline conducting polymer films have been prepared in a protic acid medium (HCl) by potentiodynamic method in an electrochemical cell and studied by cyclic voltammetry and FTIR techniques. The FTIR spectra confirmed Cl^- ion doping in the polymers. The polymerization rate was found to increase with increasing concentration of aniline monomer. But the films obtained at high monomer concentration were rough having a nonuniform flaky polyaniline distribution. Results showed that the polymerization rate did not increase beyond a critical HCl concentration. Cyclic voltammetry suggested that, the oxidation-reduction current increased with an increase in scan rate and that the undoped polyaniline films were not hygroscopic whereas chloride doped polyaniline films were found to be highly hygroscopic.     

循环伏安法在润滑油检测中的应用

介绍了循环伏安法的产生背景、原理。应用该技术可以快速、方便地对润滑油中抗氧剂、总酸（碱）值进行测定，并且可以对不同厂家润滑油的抗氧剂包进行区别。该技术还可以有效地评价润滑油的使用寿命和设备工作状况。     

试论循环水装置的经济性及其成本分析

通过对循环水装置的投资和成本分析，阐述了建设该装置的经济性和社会意义。     

自适应阵对角线加载研究

本文分析了对角线加载对自适应阵性能的影响，提出了加载门限的概念，以及加载门限的计算公式，为加载量的选取提供了方法和依据，并将加载研究的结果加以推广，提出了有效的ＬＳ自适应波束形成算法的非零初始化方法。     

氧化铝陶瓷缺口件循环疲劳及断裂机理

用实验方法研究了Ａｌ＿２Ｏ＿３陶瓷缺口试件在循环载荷作用下的疲劳寿命。结果表明，缺口导致的应力集中效应显著降低了循环疲劳寿命；若用缺口根部最大应力为应力水平，则不同缺口半径陶瓷试件具有相同疲劳断裂规律，说明陶瓷材料的疲劳集中系数和理论应力集中系数相同。本文还分析讨论了陶瓷材料的循环疲劳寿命表达式和循环疲劳断裂机理。     

预处理工艺对硬质合金与金刚石膜间粘结力的影响

在两种经不同预处理的硬质合金YG8基底上，采用微波等离子体化学气相沉积法，在微波功率2kW，压强4.0kPa和6.5kPa，CH4和H2流量分别为1.6cm/s和100.0cm/s的条件下生长金刚石薄膜。利用X射线衍射检测了金刚石薄膜是否存在，用拉曼光谱分析了薄膜的质量，用金相显微镜观察了薄膜的洛氏硬度压痕，标定并比较了不同预处理工艺膜与基底的结合力。实验结果表明，不同的预处理方法对于粘结力的影响不大，最主要的因素是钴含量的多少。     

The effect of doubly tapered strut morphology on the plastic yield surface of cellular materials

Although the literature on the mechanics of cellular materials is vast, there is no theoretical model to account for the effects of axial yielding of struts aligned to the applied loading direction on the plastic yield surface under multiaxial loading conditions. An anisotropic hexagonal model having tapered strut morphology is developed to show these effects on the plastic yield surface under multiaxial tensile loading condition. This model covers several types of cellular structure such as two-dimensional (2D) hexagonal and square cellular materials, and three-dimensional (3D) hexagonal and rhombic cellular materials of rod-like columnar structure. A tetrahedral element with tapered strut morphology is also used for a foam model to illustrate these effects on the yield surface under axisymmetric loading condition. Plastic collapse due to bending moment in the inclined struts is a dominant mode. However, under multiaxial tensile loading, the collapse due to axial yielding of struts parallel to the loading direction is found to be an important mode. The shape of plastic yield surface was found to depend not only on relative density but also on the strut morphology.