Chloride migration in concrete with superabsorbent polymers

Superabsorbent polymers (SAP) can be used as a means for internal curing of concrete. In the present study, the development of transport properties of concrete with SAP is investigated. The chloride migration coefficient according to NT BUILD 492 is used as a measure of this. Twenty concrete mixtures are tested 7, 14, and 28 days after casting. The development of degree of hydration is followed for 20 corresponding paste mixtures.Both when SAP is added with extra water to compensate the SAP water absorption in fresh concrete and without extra water, the internal curing water held by SAP may contribute to increase the degree of hydration. No matter if SAP is added with or without extra water, it appears that the so-called gel space ratio can be used as a key parameter to link age and mixture proportions (water-to-cement ratio and SAP dosage) to the resulting chloride migration coefficient; the higher the volume of gel solid relative to the space available for it, the lower the chloride migration coefficient, because the pore system becomes more tortuous and the porosity becomes less.     

AgNO<Subscript>3</Subscript> spray tests: advantages,weaknesses, and various applications to quantify chloride ingress into concrete. Part 1: Non-steady-state diffusion tests and exposure to natural conditions

Within the framework of the evaluation and the prediction of chloride-induced corrosion risks, simple and rapid AgNO₃ spray tests can be proposed for various issues. This paper forms the first part of a series. In this first part, the Maultzsch procedure (spraying of 0.1-N AgNO₃ solution + K₂CrO₄) as well as the procedure based on the use of a sole AgNO₃ solution have been investigated on a broad range of concretes. These procedures have also been compared to the Collepardi procedure (spraying of 0.1-N AgNO₃ + fluoresceine). The feasibility of these colorimetric techniques on saturated specimens cast in laboratory, after non-steady-state diffusion tests carried out in various conditions, is discussed. In addition, the results obtained from applying such spray tests in field conditions on cores drilled out from various RC test specimens exposed to a marine environment (tidal zone) and to a road and cold environment (freezing-thawing cycles and spraying of deicing salts) are presented. Colorimetric methods have in particular been applied here to the assessment of the average chloride penetration depth and of its evolution versus time (kinetics). Moreover, the detection threshold of these techniques has been investigated in various environments. The possible sources of discrepancy on the results have been analysed.     

Diffusion-controlled size-selective chloride ion sensing in the presence of bromide ion using a thin, nanoporous, plasma-polymerized coating on an Ag/AgCl electrode

We have developed a diffusion-controlled size-selective method for sensing chloride ion in the presence of bromide ion, based on a thin, nanoporous, plasma-polymerized coating of hexamethyldisiloxane on an Ag/AgCl electrode. Sub-nanometer-sized pores responsible for a highly cross-linked polymer network in the plasma-polymerized coating allowed diffusion-controlled permeation of chloride ion while blocking the larger bromide ion. An electrode coating of thickness greater than 70 nm enabled chloride detection in the concentration range 1-10 mM in the presence of 0.63 mM bromide ion. Advantages of this approach are: (1) simple design compared with ionophore-based strategies and (2) compatibility with microfabrication and mass production processes.     

Magnetic resonance imaging of H, Na, and Cl penetration in Portland cement mortar

The first magnetic resonance imaging profiles of chloride content in low- and high-permeability Portland cement mortar have been obtained using a novel material science imaging technique. The penetration of water as well as chloride and sodium ions, into mortar specimens was monitored for a period of 72 h. Marked differences in penetration depth were observed in low- and high-permeability mortar. These preliminary experiments show significant differences between the extent and nature in the penetration of chlorides compared to water and sodium.     

Properties of latex blends and its modified cement mortars

In this paper, the mechanical properties of three latex blends and the mechanical properties and chloride diffusivity of the latex-modified mortars are studied. The relationships between the properties of polymer films formed from latex blends and the properties of the latex blend-modified mortars are illustrated. The test results showed that the modified mortar with the blend of styrene-acrylic ester (SAE) and styrene-butadiene rubber (SBR) showed synergistic effect; especially the flexural strength of the SAE/SBR blend-modified mortars was about 20-40% higher than that of monolatex-modified mortars. However, the vinyl chloride-vinylidene chloride copolymer (PVDC)/SBR and PVDC/SAE blends-modified mortars showed antisynergistic effect. The compressive strength of the modified mortars increased with the increasing of the tensile strength of the latex films, while the flexural strength of the modified mortars did not depend on the tensile strength of the latex films. When PVDC with the mass fraction of 0.2 or SAE copolymer emulsion with mass fraction of 0.4 was blended into SBR latex, the latex blend-modified mortars showed lower chloride diffusivity. The chloride diffusivity of the modified mortars increased approximately linear with the tensile strength of the latex blend films, and decreased with increase of the elongation at rupture of the latex blend films. When the elongation at rupture of the latex blend films increased from 200-300% to more than 800%, the chloride diffusivity of the modified mortars decreased from 10-15×10⁻¹² to 3-4×10⁻¹² m²/s.     

Impact of specification changes on chloride-induced corrosion service life of bridge decks

A model was developed to determine the time to first repair and to subsequently rehabilitate concrete bridge decks exposed to chloride deicer salts. Said model incorporates the statistical nature of factors affecting the corrosion process. The time to first repair and rehabilitate was predicted for 10 bridge decks built in Virginia between 1981 and 1994.The model was validated using historical service life data for 129 bridge decks built in Virginia between 1968 and 1972. The time for rehabilitation predicted for the newer set of bridge decks was approximately 13 years longer than the normalized time for rehabilitation projected for the older bridge decks. The increase in time for rehabilitation for the newer set of bridge decks was attributed to a reduction in the specified maximum water/cement ratio and increase in clear cover depth. The probabilistic model is shown to be an advancement over the deterministic model currently in use.     

The effect of Cu-rich sub-layer on the increased corrosion resistance of Cu-xZn alloys in chloride containing borate buffer

The electrochemical behaviour of Cu-xZn alloys, as well as their constituent metals, in a borate buffer containing chloride ions in the molar range from 0.01 to 1 M are studied. Characteristics of these materials under anodic polarization are compared and the composition and morphology of the corrosion products formed in the course of polarization experiment are analysed by SEM and EDS. X-ray photoelectron spectroscopy and electrochemical impedance measurements are used for characterization of the surface layers formed on Cu, Zn and Cu-40Zn alloy during 2-h immersion at E_oc in a borate buffer containing two different concentrations of chloride ions. New aspects of the behaviour of brass under E_oc condition are revealed. The improved corrosion resistance of brass in chloride media, if compared to zinc metal, is attributed to a Cu-rich layer formed by the selective dissolution of zinc. Based on the results, a structural model describing the improved corrosion resistance of Cu-40Zn alloy with respect to Zn metal is proposed.     

铵离子交换处理负硬水供锅炉应用技术

本文论述了负硬水只用氯化铵再生时离子交换器的运行过程及离子交换软化除碱的方法,并阐述了控制出水中残留碱的简便方法。经研究证明,此方法可达到除碱度、除硬度、除盐、延长锅炉使用寿命、减少腐蚀、减少排污量、节约燃煤等效果。经济效益十分显著。     

Cathodic processes in the leaching and electrochemistry of covellite in mixed sulfate–chloride media

The cathodic processes that occur on a covellite (CuS) surface in mixed sulfate–chloride solutions in the absence and presence of copper(II) ions have been studied using potentiostatic transients and cyclic voltammetry at rotating disk electrodes in the potential range 0.3–0.7 V (versus SHE). This range is relevant to the oxidative leaching of this copper mineral in sulfate and chloride lixiviants. Variations in the concentrations of sulfate and chloride ions had a small effect on the cathodic reduction of covellite in the potential range of 0.5–0.3 V, although the presence of chloride ion resulted in a significant increase in the anodic current on the reverse sweep. On the other hand, addition of copper(II) ions resulted in enhanced cathodic currents and subsequent anodic currents in both sulfate and chloride solutions due to reduction of covellite to an undefined reduced copper sulfide species. Reduction of copper(II) to copper(I) ions becomes the preferred cathodic reaction as the concentration of chloride ions increases, becoming mass transport controlled at a rotating disc electrode at potentials below about 0.4 V. Potentiostatic measurements at potentials negative to the mixed potential in acidic chloride solutions have shown that reduction of copper(II) ions is reversible and have been used to estimate the rate of oxidative dissolution of the mineral which value agrees reasonably well with previously reported leaching rates under similar conditions. Reduction of dissolved oxygen has been found to be very much slower that that of copper(II) ions under ambient conditions.     

Stability of protective oxide films in waste incineration environment—solubility measurement of oxides in molten chlorides

Solubility measurements of several oxides in molten NaCl-KCl and NaCl-KCl-Na₂SO₄-K₂SO₄ were conducted in three different levels of basicity. The dissolution behavior of the oxides showed almost the same tendency as that shown by the dissolution behavior of the oxides in molten Na₂SO₄ in literature. In a waste incineration environment, a protective Cr₂O₃ film easily dissolves in molten chlorides as CrO₄²⁻ because pO²⁻ of the molten chlorides tends to have a small value due to the effect of water vapor contained in the combustion gas. From the result of the solubility measurement, the addition of molybdenum and/or silicon was expected to improve the corrosion resistance of alloys. Laboratory corrosion tests confirmed this expectation. However, the scale analysis suggested that the effect of molybdenum could not be explained completely by only the mechanism derived from the result of the solubility measurement.