光电设备电子机柜布线工艺研究

作为信号和电能载体的导线，同时也是噪声的载体和外来噪声侵入设备的媒体。描述了噪声通过导线侵入设备内部的方式，通过降低噪声的途径确定了机柜布线的原则，介绍了布线的要求和方法，最后提出了用布线槽布线的建议。     

IS-2000规范在Walsh Code定义上的局限性

本文针对IS-2000规范关于W alsh Code的定义,发现IS-2000规范有关W alshCode的定义不合理,在前向RC 3下限制了最大数据用户数和最高数据速率;如按本文修改规范关于W alsh Code的定义,不但可以在前向RC 3下提高最大数据用户数,同时在理论上可以将最高数据速率提高一倍。     

一种实现最佳用户检测的非线性优化神经网络

本文提出并讨论了实现码分多址（CDMA）系统上最佳多用户检测（MUD）的一种神经网络方法。该方法通过将最佳多用户检测视为非线性优化组合问题，利用神经网络能有效求解非线性优化问题的优势，导出了一种非线性优化神经网络来实现最佳多用户检测，理论分析和计算机模拟表明，所提出的神经网络具有可实时应用的动态性能和较传统方法优越得多的误码率性能和抗多址干扰的性能。     

采用区内C／I平衡的多区峰窝CDMA系统下行链路的性能

本文对采用区内Ｃ／Ｉ平衡的多区蜂窝ＣＤＭＡ系统下行链路的性能进行分析，给出两种区内Ｃ／Ｉ平衡算法并比较它们的性能，考虑呈对数正态分布的阴影和Ｒ＾－４规律的路径损失的综合影响，采用与传统不同的小区平均中断概率来评价系统的性能。     

用AT89C2051设计的PC键盘

在介绍PC键码特征的基础上,可利用AT89C2051来实现PC键盘的硬件设计.它具有结构简单、选择性强、便于实现等优点,特别适用于36个以下PC键盘的应用.     

实现CDMA最佳多用户检测的神经网络方法

提出并讨论了两种实现码分多址系统中最佳多用户检测的神经网络方法。一种基于离散Ｈｏｐｆｉｅｌｄ神经网络，另一种基于采用反向传播算法的多层感知器神经网络。理论分析和计算机模拟都证实了这两种神经网络方法的可行性，优越性和实用性。前者适用“固定”用户情况；后者既可用于“固定”用户吼适用于移动用户的情况，因而在未来的ＣＤＭＡ个人通信网中有较好的应用前景。     

条形码中距离动态识别技术研究

本文讨论了条形码中距离动态识别技术中扫描景深与扫描光束波长和条宽等要素之间的关系，提出了改善条形码读取距离的３种方法。为扩大条形码在工业过程控制、企业管理等领域的应用范围提供了理论依据。     

Simulation of the VVER-1000 pump start-up experiment of the OECD V1000CT benchmark with CATHARE and TRAC-PF1

In the framework of joint effort between the Nuclear Energy Agency (NEA) of OECD, the United States Department of Energy (US DOE), and the Commissariat a l'Energie Atomique (CEA), France a coupled three-dimensional (3D) thermal-hydraulics/neutron kinetics benchmark for VVER-1000 was defined. The benchmark consists of calculation of a pump start-up experiment labelled V1000CT-1 (Phase 1), as well as a vessel mixing experiment and main steam line break (MSLB) transient labelled V1000CT-2 (Phase 2), respectively. The reference nuclear plant is Kozloduy-6 in Bulgaria. The overall objective is to assess computer codes used in the analysis of VVER-1000 reactivity transients. A specific objective is to assess the vessel mixing models used in system codes. Plant data are available for code validation consisting of one experiment of pump start-up (V1000CT-1) and one experiment of steam generator isolation (V1000CT-2). The validated codes can be used to calculate asymmetric MSLB transients involving similar mixing patterns. This paper summarizes a comparison of CATHARE and TRAC-PF1 system code results for V1000CT-1, Exercise 1, which is a full plant point kinetics simulation of a reactor coolant system (RCS) pump start-up experiment. The reference plant data include integral and sector average parameters. The comparison is made from the point of view of vessel mixing and full system simulation. CATHARE used a six-sector multiple 1D vessel thermal-hydraulic model with cross flows and TRAC used a six-sector, 18-channel coarse-mesh 3D vessel model. Good agreement in terms of integral parameters and inter-loop mixing is observed.     

A Low-Complexity Multiuser Detector for Asynchronous CDMA QPSK Adaptive Antenna Array Systems

This paper proposes a low complexity joint space-time multiuser detection algorithm for asynchronous DS/CDMA antenna array systems. The proposed multiuser detector is composed of an adaptive antenna array, used as a linear beamformer, and a sliding window decorrelator. A QPSK modulation scheme is used in order to increase bandwidth efficiency. Numerical results are given in terms of Bit Error Rate (BER) under the assumption of a frequency-selective Rayleigh slow fading channel. In particular, the proposed receiver is shown to be near-far resistant, even in worst fading cases, and to exploit completely array introduction while maintaining acceptable computational complexity. The proposed architecture avoids linear filter realization of the decorrelator, which is impractical in the case of a large number of users, and operates with relatively short data frames instead of the complete information sequence. Finally, this receiver is very flexible to changes in timing configuration.     

简化源项计算方法

利用程序包STCP估算核电厂在发生严重事故情况下释放到环境的放射性源项需要耗费大量计算机时间和费用。所以,对所有感兴趣的事故情景完成源项程序包的计算实际上是不可能的。为此,发展了一个简化源项计算方法。它的基本思想如下:首先利用STCP计算几个选择的序列,然后根据放射性释放和事故进程的特点处理和分析由STCP计算得到的结果,得出一些特定参数,其它事故序列的源项能够通过这些参数的重新组合得到。