Effect of grinding-induced cyclic heating on the hardened layer generation in the plunge grinding of a cylindrical component

This paper discusses the effects of the grinding-induced cyclic heating on the properties of the hardened layer in a plunge cylindrical grinding process on the high strength steel EN26. It was found that a multi-pass grinding brings about a uniform and continuous hardened layer along the circumference of the cylindrical workpiece. An increase of the number of grinding passes, leads to a thicker layer of hardening, a larger compressive residual stress and a deeper plastic deformation zone. Within the plastic deformation zone, the martensitic grains are refined by the thermo-mechanical loading, giving rise to a hardness of 12.5% higher than that from a conventional martensitic transformation. The coupled effects of heat accumulation and wheel wear in the multi-pass grinding are the main causes for the thickening of the hardened layer. A too small infeed per workpiece revolution would result in insufficient grinding heat, and in turn, bring about an undesirable tempered hardened layer and a reduction of its hardness.     

壳体理论在水压爆破中的应用

在壳体理论的基础上,考虑到薄壳型结构水压爆破的特点,提出了一种新的药量计算公式,并得到了初步实际工程验证.     

Deformation analysis of skew ruled surface shells by moiré interference

The use of thin film grids coated on surfaces is described in relation to the determination of deformations in doubly curved shells. The technique is called the coating film moiré interference method and employs a laser holographic approach.     

An efficient assumed strain element model with six DOF per node for geometrically non-linear shells

The present paper describes an assumed strain finite element model with six degrees of freedom per node designed for geometrically non-linear shell analysis. An important feature of the present paper is the discussion on the spurious kinematic modes and the assumed strain field in the geometrically non-linear setting. The kinematics of deformation is described by using vector components in contrast to the conventional formulation which requires the use of trigonometric functions of rotational angles. Accordingly, converged solutions can be obtained for load or displacement increments that are much larger than possible with the conventional formulation with rotational angles. In addition, a detailed study of the spurious kinematic modes and the choice of assumed strain field reveals that the same assumed strain field can be used for both geometrically linear and non-linear cases to alleviate element locking while maintaining kinematic stability. It is strongly recommended that the element models, described in the present paper, be used instead of the conventional shell element models that employ rotational angles.     

介质加载圆柱腔的场分析

本文应用严格场匹配法解决了介质加载圆柱腔的本征问题，计算了圆柱腔在纵向部分填充介质后ＴＥ０１ｎ模和ＴＭ０１ｎ模的本征频率和本征场型的变化。特别分析了本征模式在空气段为截止模的情况。本文的分析方法亦可应用到纵向部分填充介质的传输线和其它形状的谐振腔。     

安全壳钢衬的初始后屈曲分析

基于Ｄｏｎｎｅｌｌ的非线性板壳理论，认为钢衬壳是一种有特殊缺陷形状的钢衬板，用初始后屈曲渐进分析理论，研究了在温度应力作用下缺陷钢衬板即钢衬壳的初始后屈曲性态。计算了一个四点铆固钢衬壳模型，同时给出了铆钉间距等参数对钢衬壳屈曲极值温度的影响。     

Flow of granules through cylindrical hopper

The gravity flow characteristics of pharmaceutically important granules were studied in a cylindrical hopper with attachable orifice disk at the bottom. Results indicate that materials property and orifice diameter play key role in determining mass flow rate while keeping environmental condition (temperature) at fixed range. A new dimensionally analyzed equation was developed to predict gravity flow of pharmaceutically important granules. The developed correlation agreed well with the experimental data. Calcium gluconate and lactose were used for preparing granules. Generally, glidant/lubricant materials are added to pharmaceutical granules during tablet manufacturing process, in order to improve physical property of granular material. Hence, the effect of glidant/lubricant on mass flow of granules through hopper was also studied. Magnesium stearate (1.5%) was added as glidant before granulation.     

Critical stress and load conditions for pitting calculations of involute spur and helical gear teeth

Calculation methods of spur and helical gear drives for preliminary designs or standardization purposes available in technical literature, use the Hertz equation to evaluate the contact stress, assuming the load to be uniformly distributed along the line of contact. However, this model presents some discrepancies with experimental results because the changing rigidity of the pair of teeth along the path of contact produces a non-uniform load distribution, which implies that some load distribution factors are required to compute the contact stress. In this paper, a non-uniform model of load distribution along the line of contact, recently developed, obtained from the minimum elastic potential criterion, has been used. This model combined with the Hertz equation yields more accurate values of the contact stress. As the load per unit of length at any point of the line of contact and any position of the meshing cycle has been described by a very simple analytic equation, a complete study of the location and value of the critical contact stress has been carried out. From this study, a recommendation for the calculation of the pitting load capacity of spur and helical gears is proposed.     

Hollow Pd/MOF Nanosphere with Double Shells as Multifunctional Catalyst for Hydrogenation Reaction

A new type of hollow nanostructure featured double metal‐organic frameworks shells with metal nanoparticles (MNPs) is designed and fabricated by the methods of ship in a bottle and bottle around the ship. The nanostructure material, hereinafter denoted as Void@HKUST‐1/Pd@ZIF‐8, is confirmed by the analyses of photograph, transmission electron microscopy, scanning electron microscopy, powder X‐ray diffraction, inductively coupled plasma, and N₂ sorption. It possesses various multifunctionally structural characteristics such as hollow cavity which can improve mass transfer, the adjacent of the inner HKUST‐1 shell to the void which enables the matrix of the shell to host and well disperse MNPs, and an outer ZIF‐8 shell which acts as protective layer against the leaching of MNPs and a sieve to guarantee molecular‐size selectivity. This makes the material eligible candidates for the heterogeneous catalyst. As a proof of concept, the liquid‐phase hydrogenation of olefins with different molecular sizes as a model reaction is employed. It demonstrates the efficient catalytic activity and size‐selectivity of Void@HKUST‐1/Pd@ZIF‐8.