粉土界面恒刚度循环剪切试验研究

竖向循环荷载作用下桩土界面的作用机理是研究桩土摩擦疲劳的关键。针对循环荷载作用下桩-粉土界面的剪切性能,使用改进的剪切试验装置在恒刚度条件下进行循环剪切试验,研究循环次数、累积位移和法向刚度对其摩擦疲劳性能、循环后单调剪切性能的影响。试验结果表明,粉土在循环剪切过程中,法向应力和剪应力在初始10个循环内随循环数增加快速衰减,随着循环进行,逐渐趋于稳定;单次循环内在剪切位移方向变化时,土体呈现表现出剪缩-剪胀-剪缩交替现象,总体变形呈现剪缩的趋势;循环荷载作用下,粉土界面的法向应力和剪应力随法向刚度增大衰减速率增大,达到稳定的累积循环位移越小;粉土循环后的单调剪切、法向应力恢复的单调剪切的剪应力比小于首次单调剪切试验值,且法向应力恢复的循环后剪切试验的剪胀程度较小,表明循环剪切过程中界面处粉土颗粒棱角破碎,颗粒变得光滑。在对试验数据分析的基础上,提出了与累积位移、法向刚度和初始应力相关的无量纲累积位移,建立了法向应力和界面摩擦角随累积位移的衰减方程。     

“Size effect” in the fatigue behavior of Friction Stir Welded plates

Comparative fatigue tests were carried out on Friction Stir Welded specimens of a 2195-T8 aluminum–lithium alloy that differed significantly in width. The width of the larger specimens was over thirteen times greater than that of the small specimens. Fatigue results showed a clear “size effect”, i.e. fatigue life of large specimens was about 40% of the corresponding value of small specimens. The Equivalent Initial Flaw Size methodology was adopted to correlate the two sets of results. Fatigue crack initiation life was disregarded with respect to crack propagation life, and fatigue life was evaluated only as propagation of a small pre-existing defect. Following this methodology, test results of small specimens were used to evaluate the initial equivalent flaw contained in each specimen. It was assumed that this data followed a normal distribution. The equivalent initial flaw in larger specimens was evaluated by simple geometrical considerations. A very good assessment of mean fatigue life and scatter in the fatigue results of large specimens was obtained by simulating the propagation of these defects. Calculations were carried out by taking also welding residual stresses into account, but the results demonstrated that this effect was not significant.     

砾岩储层精细描述中标准测井资料的应用

克拉玛依油田七区的标准测井资料是指使用标准电极系视电阻率测井、自然电位测井和井径测井,以相同的1:500深度比例尺及相同的横向比例进行测井作业所取得的资料.这种资料本来并不具备定量解释储层孔隙度和含油饱和度的能力,但这种资料占该区测井资料总量的比率高达34%.利用标准电极系视电阻率资料和岩心分析资料建立了视电阻率-岩性图版,利用自然电位减小系数α和岩心孔隙度分析资料φ建立了α-φ图版,根据综合测井资料求出标准测井视电阻率校正系数,进而确定了饱和度计算方程的参数.与相应的综合测井资料计算结果相对比,用该方法得到的孔隙度平均绝对误差及相对误差分别为1.85%和11.88%;含油饱和度平均绝对误差及相对误差分别为9.08%和24.75%.将该方法有选择地应用到该区砾岩储层精细描述研究中,弥补了缺乏综合测井资料无法进行测井储层评价及参数研究的缺陷.     

A continuum-based modeling of MEMS devices for estimating their resonant frequencies

A continuum-based modeling of coupled electrostatics-structure interactions is presented for the frequency computations of MEMS devices. The present general formulation of electrostatics accounting for free space is validated first by specializing it to one-dimensional uniform motion of conducting surfaces and comparing the resulting electrostatics to conventional lumped models. The general coupled electrostatics-structure interactions are then applied for the prediction of resonant frequencies of MEMS devices due to bias-voltage changes and temperature variations. Comparisons of predicted resonant frequencies obtained by the present coupled electrostatics-structure interaction models with experimental results available in the literature demonstrate that the proposed continuum-based interaction modeling yields high-confidence predictions of resonant frequencies of MEMS devices.     

环境敏感因素对电站正常蓄水位选择的影响

卜寺沟水电站预可阶段正常蓄水位是考虑规划成果、地形、地质务件、梯级衔接、水库淹没、筑坝技术、水能资源利用等因素综合初选的.从理论角度分析,水库淹没时水库内寺庙的影响,按全部淹没进行经济补偿处理代价较小;其社会环境敏感因素对正常蓄水位的选择不应起决定性作用.但是,考虑到少数民族群众、僧侣和地方政府的要求,适当降低正常蓄水位,以减少对扎西日岗寺庙的影响,将带来较积极的社会影响.     

Lattice structure on some fuzzy algebraic systems

In this paper, we study the lattice structure of some fuzzy algebraic systems such as (G-)fuzzy groups, some fuzzy ordered algebras and fuzzy hyperstructures. We prove that under suitable conditions, these structures form a distributive or modular lattice. This research partially is supported by the “ Fuzzy Systems and its Applications Center of Excelence, Shahid Bahonar University of Kerman, Iran”.     

A direct stiffness analysis of a composite beam with partial interaction

The use of the conventional semi-analytical stiffness method in finite element analysis, in which interpolation polynomials are used to develop the stiffness relationships, leads to problems of curvature locking when beam-type elements are developed for composite members with partial interaction between the materials of which it is comprised. The curvature locking phenomenon that occurs for composite steel–concrete members is quite well reported, and the general approach to minimizing the undesirable ramifications of curvature locking has been to use higher-order polynomials with increasing numbers of internal nodes. This paper presents an alternate formulation based on a direct stiffness approach rather than starting from pre-defined interpolation polynomials, and which does not possess the undesirable locking characteristics. The formulation is based on a more general approach for a bi-material composite flexural member, whose constituent materials are joined by elastic shear connection so as to provide partial interaction. The stiffness relationships are derived, and these are applied to a simply supported and a continuous steel–concrete composite beam to demonstrate the efficacy of the method, and in particular its ability to model accurately both very flexible and very stiff shear connection that causes difficulties when implemented in competitive semi-analytical algorithms. Copyright © 2004 John Wiley & Sons, Ltd.     

实行全面质量管理 做好江口水电站工程设计

江口水电站是芙蓉江干流开发中的骨干工程。为认真履行江口工程的设计合同，确保优质、高效地完成江口工程的各项设计工作，长江委设计院实行全面质量管理，建立了一套规范化的统计管理程序，制订详细的设计计划，落实江口工程项目各级责任人的质量责任制，采取特殊技术措施，对工程设计过程中的各项质量活动进行全过程的管理，使江口工程在满足质量标准、合同进度的情况下，工程投资最省。     

新产品——钢带增强聚乙烯螺旋波纹管

钢带增强聚乙烯螺旋波纹管是一种创新的埋地排水管,把钢材的高刚度、高强度和聚乙烯的柔韧、耐腐结合在一起,突出的优点是环刚度高和节约原材料.