Synthesis and characterization of superoleophobic fumed alumina nanocomposite coated via the sol-gel process onto ceramic-based hollow fibre membrane for oil-water separation

Oily wastewater treatment is a global challenge due to the substantial amount of effluent resulted from many industrial and domestic activities. To overcome the challenge of using existing treatment approach and fouling, superoleophobic coatings were fabricated. In this study, a superoleophobic membrane surface was obtained using the sol-gel technique with perfluorooctanoate (PFO), poly (diallyl dimethylammonium chloride) (PDADMAC), and nanoparticles as complex-polymer nanocomposites. The effects of coating cycles on the surface structure, chemical properties, surface chemistry, and oleophobicity of the surface were examined using field emission scanning electron microscopy (FESEM), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and oil contact angle measurement. The results showed that the coated layer successfully adhered to the substrate surface. However, the chemical stability with respect to oil contact angle (OCA) revealed a decline at pH 7 and pH 9 and maintained stability at pH 3. Besides, oil flux at 63.0 L/m². h was achieved for PDADMAC-Al₂O₃/44 wt% PFO and the highest separation efficiency of 98% was obtained. Furthermore, the oil rejection decreases as the oil concentration increases from 1 to 3 g/L. OCA of 155° was obtained after 5 coating cycles. Apart from mitigating substrate fouling, the superoleophobic and superhydrophilic coating can be applied to a ceramic-based hollow fibre membrane and efficiently used for the separation of oil from oily wastewater.     

Preparation and antifouling performance of thin inorganic ultrafiltration membrane via assisted sol-gel method with different composition of dual additives

A novel TiO₂ thin film was prepared on the ceramic hollow fiber by the sol-gel method using poly(vinylpyrrolidone) (PVP) and polyvinyl alcohol (PVA) as additives. SEM images verified the formation of TiO₂ layer with various thickness using different composition of titania sols. The effect of the PVP and PVA contents on the TiO₂ sol properties, the separation and the antifouling performance of the ultrafiltration membranes were investigated thoroughly. When the contents of PVP and PVA were 1.0 wt% and 0.8 wt%, respectively, the resultant membrane showed a thickness of 0.55 μm with a pure water flux of 255 L m^?2 h^?1. In addition, the adherent foulant bovine serum albumin was applied to evaluate the antifouling performance. During the three fouling-recovery cycles, the flux recovery ratio and the flux decay ratio maintained about 99% and 30%. The BSA flux and rejection were still 169 L m^?2 h^?1 and 96.9% after the cycles, indicating a superior antifouling property.     

一种可替代漂珠的低密度材料

漂珠低密度水泥浆由于密度低、强度高、体系稳定而在油田低压易漏层及低压油气层长封固段固井作业中获得了广泛的应用。但近年来,由于漂珠的产量越来越少,油田低成本要求急需开发代替漂珠的新型减轻材料,以满足配制低密度水泥浆的需求。开发了BCL-10S低密度混合减轻材料,其物化性能与漂珠相当,用它作减轻剂配制的低密度水泥浆性能与用漂珠作减轻剂配制的低密度水泥浆性能相媲美,并已经在长庆油田获得了应用。     

气动贯通式潜孔锤反循环连续取心取样钻进新技术在河南钼矿中应用

三道庄钼矿勘探生产中钻遇的地层非常复杂，采用其他方法均无法实现钻进，经过分析比较，决定采用贯通式潜孔锤反循环连续取心（样）钻进新技术来解决该地层钻进难、成孔难、取样难等三大问题。文章从钻进技术特点、工作原理等方面对该技术进行详细分析，得出其具有钻进效率高、岩心（样）采取率高、成孔质量好等突出优点。并介绍了钻进主要设备机具的配套、施工工序、操作要点、遇到问题的解决方法等。在河南钼矿露天采石场应用该项技术，有效避免了塌孔和卡钻事故，工程进展顺利、质量好、岩心（样）采取率在98％以上，取得了良好的效果。针对在生产试验中遇到的某些问题，作者提出了一些改进建议。     

玻璃纤维布内中空纤维丝的检测

介绍了玻璃纤维布内中空纤维丝的检测方法。     

CA／PAN中空纤维血浆分离膜的结构与性能

本研究以CA及PAN的共混溶液,通过干-湿法纺丝制取中空纤维,利用共混高聚物各组分在凝固剂中相分离速度的差异,形成具有稳定结构的中空纤维孔膜,该膜用于分离血液中的血浆成分具有良好效果。讨论了成型条件及添加剂等对膜结构、性能的影响,用SEM及图相分析仪、MAP压汞仪及DSC等分析手段,对膜的微孔结构、形态、孔尺寸及中空纤维膜的血浆通量和水通量等进行了系统的考查。     

The influence of the fabrication process on the buckling of thin-walled steel box sections

Steel box sections are usually fabricated from flat plates which are welded at the corners. The welding process can introduce residual stresses and geometric imperfections into the sections which can influence their strength. For some thin-walled sections, large periodic geometric imperfections have been observed in manufactured sections. Subsequent investigations have indicated that the imperfections are in fact buckling deformations i.e. the box section has buckled due to welding residual stresses prior to any application of external load. The welding procedure and the behaviour of the box sections under load has been modelled using a finite element analysis that accounts for both geometric and material non-linearities. Tests have been carried out on box sections with a range of width to thickness ratios for the plate elements. Modelling has been shown to give good correlation with the test results. The conditions for buckling to take place as a result of the welding process have been established. A design method has been proposed.     

混凝土小型砌块建筑裂缝宽度的标准设置研究

通过对混凝土小型空心砌块单片墙进行试验 ,了解不同构造措施墙体的初始裂缝在墙体上出现的部位、形态、发展规律以及墙体最终破坏形态 ,并通过试验明确墙体在不同受力状态下的裂缝形态 ,最后根据试验结果初步提出混凝土小型空心砌块建筑的裂缝宽度控制标准