大掺量粉煤灰轻质墙体砌块的研制

大掺量粉煤灰轻质墙体砌块是以粉煤灰为主要原材料 ,普通硅酸盐水泥为胶凝材料 ,配以各种外加剂 ,经发泡剂发泡 ,在常温、常压条件下养护而成。具有重量轻、导热系数小、抗冻性高以及粉煤灰掺量大、成型方便、工艺简单、投资小、见效快等优点。     

Effect of Wall Surface Properties at Different Drying Kinetics on the Deposition Problem in Spray Drying

Current methods in alleviating the wall deposition problem in spray drying emphasize mainly controlling the stickiness of the drying particles and less attention is placed on the properties of the dryer wall. In this experimental study, the effect of wall surface properties on the deposition mechanism has been investigated. Properties considered in classifying different wall materials were surface energy, roughness, and dielectric properties. The model solution contained sucrose, representing low-molecular-weight sugars commonly encountered in spray drying of fruit and vegetable juices. The effect of wall properties on deposition was explored at different drying rates producing particles of different surface rigidity. Larger surface roughness produced higher deposition fluxes for particles with high impact velocity and moisture. Surface energy and surface roughness were found to have no significant effect for dry rigid particles at the middle and bottom elevation of the drying chamber. However, material with lower surface energy (Teflon) exhibited less deposition for rubbery particles at such elevations. Analysis shows that dielectric wall material (Teflon) tends to enhance deposition of dry particles because of attrition at the surface. Higher wall temperature was found to produce slightly more deposition. The results of this work give a general indication of the effect of wall material on the deposition problem and provide the fundamental understanding for further studies along this line. Proper selection of dryer wall material will provide potential alternatives for reducing the deposition problem.     

New Engineered Particles from Spray Dryers: Research Needs in Spray Drying

This article reviews developments in the simulations of spray dryer behavior, including the challenges in modeling the complex flow patterns inside the equipment, which are often highly transient and three-dimensional in nature. There appears to be considerable scope for using CFD simulations for investigating methods to reduce the rates of wall deposition and of thermal degradation for particles by modifying the air flow patterns in the chamber through small changes in the air inlet geometry. Challenges include building particle drying kinetics and reaction processes, as well as agglomeration behavior, into these simulations. The numerical simulations should be valuable supplements to pilot-scale testing, enabling more extensive and accurate optimization to be carried out than hitherto possible. New understanding of reaction processes and materials science, in combination with recent knowledge of the application of CFD to these problems, may enable new engineered powder products to be developed from the one-step spray-drying process.     

Measurements of turbulent mass transport of a circular wall jet

The results of a laboratory investigation on the turbulence characteristics of a circular three-dimensional turbulent wall jet are presented. Measurements were taken up to 50 nozzle diameters using combined particle image velocimetry and planar laser induced fluorescence. The results showed that the induced turbulence was still evolving in the present range and had not achieved similarity. While the turbulent intensity for both velocity and concentration increased downstream, the turbulent mass transport showed a decline over distance for both the streamwise and spanwise directions, implying weakening dispersion from the jet core.     

Extended Hyperbolic Model for Sand-to-Concrete Interfaces

A relatively simple, four-parameter extended hyperbolic model for interfaces was developed for use in soil-structure interaction analyses. The model accommodates arbitrary stress path directions and includes three important elements: (1) development of a yield surface during interface shear; (2) a formulation for yield-inducing shear stiffness that is applicable to any stress path orientation; and (3) a formulation for unloading-reloading shear stiffness. The model was evaluated against the results of shear tests performed at the interface between three different types of sand and a concrete surface under a variety of stress paths. Comparisons between measured and calculated interface response indicate that the model provides accurate estimates of the response of sand-to-concrete interfaces.     

外墙渗水防治措施探讨

针对建筑物外墙渗水的原因,结合施工实践对防治措施的可行性进行探讨。     

Limited reinforced space in segmental retaining walls

Current design of geosynthetic reinforced segmental retaining walls considers an a priori limitless length for reinforcement installation. Such length is typically 0.5–0.7 times the height of the wall. However, often there are constraints on such space; e.g., bedrock formation located at a small distance behind the facing. The objective of this note is to introduce a procedure for assessing the required long-term strength of the reinforcement while considering its limited length. Predictions by a conventional slope stability analysis were first checked against a continuum-mechanics based numerical analysis. Upon obtaining good agreement, a design chart was developed. The chart enables the determination of the reduction in the lateral earth pressure coefficient due to the constrained space. The revised earth pressure coefficient can be used with current analytical methods to account for the limited space. The results appear to be valid for conventional walls retaining a limited volume of soil. Comparison with limited experimental results for unreinforced backfill shows reasonably good agreement.     

钢管在线测厚和应用

钢管在线测厚是近年发展较快的一项高科技技术，该设备对生产高质量的无缝钢管具有较大帮助。叙述了钢管在线测厚的基本原理和在宝钢钢管分公司张减机上使用的实绩。     

Ф400mm自动轧管机有限元模拟及工艺优化

为提高包钢钢联股份有限公司Ф400mm自动轧管机轧制的钢管壁厚精度．进行了轧卡试验及有限元模拟分析，获得了钢管在孔型中的应变分布状况，经过优化孔型参数和改进轧辊孔型，使轧制的钢管横向和纵向壁厚偏差大大减小。     

WALL AND PARTICLE-SHAPE EFFECTS ON HEAT TRANSFER IN PACKED BEDS

The effective radial thermal conductivity and apparent heat transfer coefficient for a packed bed were experimentally determined for beds of spheres, full cylinders and hollow cylinders, for flow rates giving particle Reynolds numbers in the range 100-1000, and for tube to particle diameter ratios of 5-12. Over these ranges the radial Peclet number Pe_r showed significant dependence on solid conductivity, gas flow rate and particle shape, while the wall Biot number Bi showed significant dependence on tube to particle diameter ratio, gas flow rate and particle shape. These dependencies were predicted well by equations incorporating the effects of these variables into individual gas and solid phase parameters, which were then combined to give the effective or lumped parameters