排序方式: 共有13条查询结果,搜索用时 390 毫秒
1.
2.
通过文献阅读、实验研究、工程调查,分析了现行的地板送风系统负荷计算和送风量确定过程中存在的主要问题。实验室实验和工程实践结果表明:在国内采用地板送风系统的一般办公室中,很难形成空气分层,分层与否影响空调送风量,而送风量又决定了空气是否分层;地板送风系统的负荷和送风量计算与顶送风常规空调系统并无本质区别,考虑到人体舒适感,地板送风系统的送风温度更高,送风量一般明显大于顶送风常规空调系统。空调负荷和送风量计算是地板送风系统设计中的关键,其正确与否,不但影响系统的经济性,而且还会影响系统的可行性,有必要进行深入的研究、分析和探讨。 相似文献
3.
4.
5.
6.
地板送风系统的室内空气分层现象对准确预测系统能耗非常重要。对该系统,本文提出了一种冷负荷减少系数方法来简单而快速的计算人体活动区域的冷负荷大小。首先,把室内热源类型分为墙体、人体、电器设备和照明四种,以定热流作为边界条件,利用计算流体动态(CFD)模拟方法可以获得人体活动区域的冷负荷Qoccupied。其次,基于同样的边界条件,对上述四种不同热源单独进行数值模拟,得到人体活动区域四个不同的冷负荷减小系数α,从而得到加和冷负荷Q′occupied。本文分析了一种回风口与排风口分别位于房间中部和天花板上的地板送风系统,通过数值模拟发现Qoccupied与Q′occupied的偏差在10%以内。由于模拟计算单一热源的冷负荷减小系数非常简单,所需时间也远小于前者(Qoccupied计算),采用加和计算冷负荷的方法在工程上是切实可行的。对该地板送风系统,作者的最终目的是要建立一个冷负荷减小系数数据库,以简化整个人体活动区域冷负荷的预测方法,从而为工程设计应用提供一种实际可行的冷负荷估算方法。 相似文献
7.
采用数值模拟方法,对一应用地板送风系统的开敞式办公环境的气流组织进行模拟计算。通过对模拟结果的速度场和温度场的分析,表明了地板送风能够提供具有较好热舒适性的室内环境。 相似文献
8.
9.
In this study, numerical prediction using computational fluid dynamics (CFD) was utilized to investigate air temperature stratification in a room with an underfloor air distribution (UFAD) system. The numerical modeling using CFD computation was validated with physical test in a full size experimental room with an UFAD system. The different supply air conditions and heat loads were discussed. The results show that the effect of three parameters, heat load, supply volume flux and supply air velocity, on room air temperature would be expressed by the length scale of the floor supply jet. When the length scale increased from 0.8 to 1.56 m, the ratio of vertical temperature difference between 2.5 and 0.1 m at the occupied zone to the difference between return and supply air temperature decreased from 0.62 to 0.25. When there was only one local heat source in the room, there was a thermal stratified interface at the occupied zone. The interface height was about 1.42 times the length scale. The results may suggest ways to optimize UFAD design and operation. 相似文献
10.
通过模拟地板送风系统的两种典型系统形式,从获得的温度场、速度场、PMV场表明,下送上回系统较容易满足垂直空气温差的限值,下送下回系统容易超出垂直空气温差的限值,在低热力长度尺度(lm/H)时下送下回系统比下送上回系统容易获得舒适的环境,在高热力长度尺(lm/H)时,两种系统形式均易产生偏冷的室内环境。 相似文献