涡轮搅拌桨反应器混合过程的数值计算

利用CFD方法计算单层涡轮反应器搅拌槽内流体混合过程的速度场和浓度场,研究物料在搅拌槽内的混合过程,以及不同监测点对混合时间的影响。结果表明,搅拌槽内物料的混合主要受槽内流体的流动形式所影响;混合时间的长短与监测点位置有关;在搅拌桨的桨叶附近进行监测所得到的混合时间较短,在液面附近进行监测所得的混合时间较长。在实际生产和试验中,应注意对监测点位置的选取。     

Ring‐opening polymerization of lactones initiated by diphenylzinc–coinitiator systems

Diphenylzinc, alone or in combination with water and butanone as coinitiators, was used as a polymerization initiator system for a variety of lactones at varying temperatures. The resulting data indicate that the course of the polymerization is greatly influenced by the lactone structure, as well as by the molar ratio of coinitiator to diphenylzinc. When used alone, diphenylzinc exhibited high activity as an initiator in δ‐valerolactone polymerizations, although it was less efficient when used in the β‐butyrolactone and the β‐propiolactone polymerizations. Activity in the polymerization of β‐lactones was increased by adding small amounts of butanone or water. It was also observed that the diphenylzinc–butanone combination was more effective than the diphenylzinc–water mixture in the polymerizations of β‐butyrolactone and β‐propiolactone. Copyright © 2003 Society of Chemical Industry     

在经典极限下量子斯特林制冷机的优化

经济利润率是评价一个实际热力装置的主要指标之一。将有限时间热力学，非平衡量子统计理论和yong经济学相结合，导出了量子斯特林制冷机的最大利润率以及对应的性能界限，其结果与实际斯特林制冷机的优化设计和模型评估提供了一个最佳的预选方案。     

20世纪的泥沙运动力学

在20世纪，泥沙运动力学的研究取得了不少突出的成绩，但与其他学科同时期的进展相比，发展还是比较缓慢的。按取得的进展来看，20世纪可分为两个阶段；在上半叶，有6项突破性进展，逐步积累，到1950年，Einstein集大成，提出了第1 个泥沙运动力学理论体系。在下半叶，进入了百家争鸣的时代，一些研究者提出了自己的泥沙运动理论体系，作者列举了8个有代表性的理论体系。受计算机时代的影响，从20世纪70年 代开始出现了根据大量实测资料，利用计算机进行回归分析而得出的阻力和输沙率公式，而不拘泥于发展新的理论。与此同时，一些与实际偏离较远的理论逐渐被淘汰。在21世纪，要搜集系统完整的资料，特别是近底层的资料，并拓宽研究领域到环境，生态等学科。     

机动武器系统的含间隙动力学研究--下篇:系统仿真

本文把中篇建立的间隙铰模型引入多体系统动力学分析中,得到了一种处理含间隙多体系统动力学问题的一般方法.应用这种方法对机动武器的发射过程进行了原理性的仿真,验证了前面建立的碰撞模型和间隙模型,并分析了间隙对导弹运动状态的影响.导弹发射过程具有变拓扑的特点,本文方法提供了一种处理这类问题的思路.     

Micromechanical approach to damage mechanics of composite materials with fabric tensors

The purpose of this study is to apply continuum damage mechanics – introduced through the concept of fabric tensors – to composite materials within the framework of the theory of elasticity. A directional data model of damage mechanics for composite materials will be developed using fabric tensors. The introduction of fabric tensors into the analysis of damage of composite materials will allow for an enhanced and better understood physical meaning of damage. The micromechanical approach will be used here to relate the damage effect through fabric tensors to the behavior of composite materials. In this approach, damage mechanics is introduced separately to the constituents of the composite material through different constituents’ damage effect tensors. The damaged properties of the composite system as a whole can then be obtained by proper homogenization of the damaged properties of the constituents.

The derivation of a generalized formulation of damage evolution will be shown here in a mathematically consistent manner that is based on sound thermodynamic principles. Numerical examples will be presented to show applicability. In addition, damage evolution for the one-dimensional tension case is also illustrated.     

Brittle fracture of high-strength steels at very low temperatures

High-strength steels are used to increase the load carrying capacity of components. However, to guarantee a safe design, it is also necessary to combine high strength with adequate fracture toughness. In this paper, fracture toughness of three high-strength steels with yield strengths ranging from 460 to 890 MPa has been studied at very low temperatures. Taking into account experimental evidence, a new mechanism of cleavage at very low temperatures is proposed. This mechanism considers the possibility of reaching the ideal strength (the stress at which the lattice of a single crystal losses its stability) in the immediate vicinity of the fatigue crack tip. Moreover, a computational model able to calculate the external load needed to produce a catastrophic failure of these steels has been developed.     

A direct estimate of JIc from the load versus load-line displacement record

The purpose of this study is to examine the current standard fracture toughness test procedure to determine if there could be an easier method to get a J_Ic value from the test record. The current method for determining J_Ic involves a detailed computational and construction procedure. The objective in this study is to simplify the analysis for the determination of J_Ic. The results of this study show that the load and displacement record for a fracture toughness test can be used to directly estimate a J_Q value, a provisional value for fracture toughness, J_Ic. The J value taken at the maximum load point can be used along with an adjustment factor to estimate a J_Q value. This J_Q estimate is close to the one obtained from the construction procedure of ASTM Standard E 1820. When a unit‐sized specimen is tested, that is, a specimen with a width of 50 mm and a thickness of 25 mm the maximum load point provides a direct estimate of J_Q. Other sizes require a size adjustment factor, which is simply a square root relationship between the width of the test specimen and a unit width. The proposed new method of estimating J_Q is simple in concept and requires a minimum number of calculations. It appears to produce values of J_Q which are comparable to those obtained from the ASTM E1820 construction procedure and may produce less scatter.     

梯恩梯-吉纳、地恩梯-太安装药体系自旋爆轰特性的研究

本文研究了梯恩梯-吉纳(TNT-DINA)和地恩梯-太安(DNT-PETN)体系的自旋爆轰现象,爆轰波是以低频脉冲方式传播.这些体系具有的爆速、爆热分别为DJ=7.3～7.4km/s和Qv=(5.40±0.01)MJ/kg.不同组成的爆速和爆压PJ通过SW程序计算.用扩散区的爆压P3和爆温T3来评估爆轰波的衰减和重新点火.敏化剂含量相同,梯恩梯-黑索金(TNT-RDX)体系的爆压PJ大于TNT-DINA的爆压,TNT-RDX体系的温度T3比TNT-DINA高60～100K.计算值与实验结果吻合较好.