ACCUGRAM: A novel approach based on classification to frequency band selection for rotating machinery fault diagnosis

Frequency band selection (FBS) in rotating machinery fault diagnosis aims to recognize frequency band location including a fault transient out of a full band spectrum, and thus fault diagnosis can suppress noise influence from other frequency components. Impulsiveness and cyclostationarity have been recently recognized as two distinctive signatures of a transient. Thus, many studies have focused on developing quantification metrics of the two signatures and using them as indicators to guide FBS. However, most previous studies almost ignore another aspect of FBS, i.e. health reference, which significantly affect FBS performance. To address this issue, this paper investigates importance of a health reference and recognize it as the third critical aspect in FBS. With help of the health reference, the frequency band where the fault transient exists could be located. A novel approach based on classification is proposed to integrate all three aspects (impulsiveness, cyclostationarity, and health reference) for FBS. Classification accuracy is developed as a novel indicator to select the most sensitive frequency band for rotating machinery fault diagnosis. The proposed method (coined by accugram) has been validated on benchmark and experiment datasets. Comparison results show its effectiveness and robustness over conventional envelope analysis, the kurtogram, and the infogram.     

光照水电站装设筒形阀分析

筒形阀是一种新型的水轮机进水阀,它与球阀或蝴蝶阀相比较有防止机组飞逸事故扩大效果明显、减轻导叶全关时导水机构的快速破坏并减少漏水量,以及动水开启方便、所需时间短等优点,但对运行条件也有一定的要求。光照水电站是贵州省第1个拟采用筒形阀的电站,为此对装设筒形阀的可行性和必要性进行了认真的分析。     

随机减量技术中周期激励的影响及消除方法

本文针对机械系统中通常存在确定性周期激励的事实 ,论证了周期干扰成分的存在对提取的随机减量特征信号的影响 ,基于数字滤波技术提出了一种从周期干扰环境中提取随机减量特征信号的简便方法。在回转机械稳定性监测中的应用实例表明本文提出的方法是有效的。     

火炮身管内表面激光硬化处理的实验研究

提高身管寿命是火炮行业亟待解决的关键技术问题，激光表面改性技术是解决这一问题的有效方法之一。本文在分析激光表面相变硬化性能的基础上，对身管内表面进行了激光硬化处理实验研究，检测了其内表面阳线和阴线的硬化层硬度和深度，对比分析了离焦量和焦深对其内表面硬化层硬度的影响，并对激光相变硬化层金相组织进行了分析。经激光硬化处理后，身管的内表面硬度有明显提高，硬化层较深，且为很细的条状马氏体组织。     

The hot compaction behaviour of woven oriented polypropylene fibres and tapes. I. Mechanical properties

The aim of this work was to establish the important parameters that control the hot compaction behaviour of woven oriented polypropylene. Five commercial woven cloths, based on four different polypropylene polymers, were selected so that the perceived important variables could be studied. These include the mechanical properties of the original oriented tapes or fibres, the geometry of the oriented reinforcement (fibres or tapes), the mechanical properties of the base polymer (which are crucially dependant on the molecular weight and morphology), and the weave style. The five cloths were chosen so as to explore the boundaries of these various parameters, i.e. low and high molecular weight: circular or rectangular reinforcement (fibres or tapes): low or high tape initial orientation: coarse or fine weave.A vital aspect of this study was the realisation that hot compacted polypropylene could be envisaged as a composite, comprising an oriented ‘reinforcement’ bound together by a matrix phase, formed by melting and recrystallisation of the original oriented material. We have established the crucial importance of the properties of the melted and recrystallised matrix phase, especially the level of ductility, in controlling the properties of the hot compacted composite.     

准噶尔盆地侏罗系储集层的基本特征及其主控因素分析

从描述储集层基本特征、分析储集层性质的主控因素、建立储集层成因模式和评价、预测储集层性质这 4个层次 ,研究准噶尔盆地重点勘探目标区的侏罗系储集层。系统总结侏罗系储集层岩石学特征 ,认为成岩压实作用强弱是控制储集层性质的关键因素 ;指出相对优质储集层均为剩余原生粒间孔隙型储集层 ,溶蚀作用对渗透率贡献小 ;非煤系储集层的孔隙保存条件明显比煤系储集层好 ,这是三工河组、头屯河组和吐谷鲁群的物性普遍优于八道湾组和西山窑组的原因。在确定储集层性质的控制因素和控制机理基础上 ,建立了煤系和非煤系两大类储集层的成因 演化模型。在上述研究的基础上 ,分地区、分层位评价了储集层 ,并预测了不同渗透率储集层的深度界线及相对优质储集层的平面分布。图 6参 10     

KZON-50/120空分设备的安装调试及设计改造

在KZON-50/120空分设备的安装调试和试运行过程中,对其机械和电器部分进行了多处改造,克服了原设计中存在的不足之处。改造后,机械和电器性能更加趋于合理,操作简单,便于维护,降低了制气费用,提高了制气纯度和经济效益,保证了空分设备更加安全可靠运行。     

压密注浆及其在地基加固中的应用

在简单介绍了压密注浆工法的加固机理、影响被加固土体强度的因素的基础上，结合工程实例介绍了压缩注浆工法的工程应用情况。     

Clay compaction modelling by homogenization theory

The modelling of hydromechanical behavior of clayey sediments by homogenization theory is described. The rheological model of clays buried in depth requires a three-dimensional approach and laboratory experiments to quantify the model parameters. An iterative process which can be coupled to any homogenization method is used to model the porous media behavior. Hydromechanical compaction results from oedometric experiments are simulated with the proposed model.     

关于陶瓷墙地砖的深加工及其机械

本文简要回顾了陶瓷墙地砖深加工的工艺理论和机械设备。对陶瓷墙地砖深加工的自动抛光生产线和组成生产线的工艺单机作了一般介绍。指出设计陶瓷墙地砖深加工工艺单机时要注意的主要问题,并提供了解决这些问题的方法。