Microstructure,wear and corrosion characteristics of multiple-reinforced (SiC–B4C–Al2O3) Al matrix composites produced by liquid metal infiltration

In this study, AA7075 aluminum matrix composites reinforced with the combination of SiC, Al₂O₃, and B₄C particles were fabricated by the liquid metal infiltration method. The effects of the relative ratio of B₄C and Al₂O₃ particles on the microstructural, wear, and corrosion features of the composite samples were analyzed using XRD, light metal microscopy, SEM, EDS, Brinell hardness, ball-on-disc type tribometer, and potentiodynamic polarization devices. It was determined that infiltration occurred more successfully, and homogenously distributed particles with reduced porosity were obtained as the amount of Al₂O₃ increased. Worn surface studies revealed that the specimens were predominantly worn by abrasion and adhesion. The increase in B₄C/Al₂O₃ ratio caused a decrease in the hardness and wear strength, whereas it increased the corrosion resistance.     

TiO2/MXene-Assisted LDI-MS for Urine Metabolic Profiling in Urinary Disease

Cancer remains an intractable medical problem. Rapid diagnosis and identification of cancer are critical to differentiate it from nonmalignant diseases. High-throughput biofluid metabolic analysis has potential for cancer diagnosis. Nevertheless, the present metabolite analysis method does not meet the demand for high-throughput screening of diseases. Herein, a high-throughput, cost-effective, and noninvasive urine metabolic profiling method based on TiO₂/MXene-assisted laser desorption/ionization mass spectrometry (LDI-MS) is presented for the efficient screening of bladder cancer (BC) and nonmalignant urinary disease. Combined with machine learning, TiO₂/MXene-assisted LDI-MS enables high diagnostic accuracy (96.8%) for the classification of patient groups (including 47 BC and 46 ureteral calculus (UC) patients) from healthy controls (113 cases). In addition, BC patients can also be identified from noncancerous UC individuals with an accuracy of 88.3% in the independent test cohort. Furthermore, metabolite variations between BC and UC individuals are investigated based on relative quantification, and related pathways are also discussed. These results suggest that this method, based on urine metabolic patterns, provides a potential tool for rapidly distinguishing urinary diseases and it may pave the way for precision medicine.     

Compressive strength and wear properties of SiC/Al6061 composites reinforced with high contents of SiC fabricated by pressure-assisted infiltration

Pressure-assisted infiltration was used to synthesize SiC/Al 6061 composites containing high weight percentages of SiC. A combination of PEG and glass water was used to fabricate SiC preforms and the effect of the presence of glass water on the microstructure and mechanical properties of the preforms was evaluated by performing compression tests on the preforms. Also, the compressive strength and the hardness of the SiC/Al composites were investigated. The results revealed that the glass water improved the compressive strength of the preforms by about five times. The microstructural characterization of the composites showed that the penetration of the aluminum melt into the preforms was completed and almost no porosity could be seen in the microstructures of the composites. Moreover, the composite containing 75 wt% SiC exhibited the highest compressive strength as well as the maximum hardness. The results of the wear tests showed that increasing the SiC content reduces the wear rate so that the Al-75 wt% SiC composite has a lower wear rate and a lower coefficient of friction than those of Al-67 wt% SiC composite. This indicated higher wear resistance in these composites than the Al alloy due to the formation of a tribological layer on the surface of the composites.     

不同管距时玉米渗灌效果的试验研究

在运城市夹马口灌区和红旗灌区进行了1996,1997两个年度的玉米渗灌试验,研究了不同毛管间距条件下渗灌对其产量及水分生产率等的影响。结果表明,玉米渗灌毛管间距采用0.8~1.0 m较为适宜。毛管间距愈大,产量愈低;渗灌较地面灌平均减产7.23%,较旱地平均增产30.8%;玉米生长期内总耗水量地面灌最大,渗灌次之,旱地最小。渗灌可明显提高玉米水分生产率,渗灌处理水分生产率平均为1.65 kg/m3,是地面灌的1.2倍,是旱地的1.33倍;两年度渗灌较地面灌平均节水44.4%。     

Design Methodology and Area Sensitivity Analysis of Horizontal Subsurface Flow Constructed Wetlands

An approach is presented to satisfy the demand for simple criteria, guidelines and models for the preliminary sizing of horizontal subsurface flow (SF) constructed wetland systems. This approach eliminates time-consuming calculations and iterations by providing graphical solutions for wetland system sizing. Therefore, it can be used for the preliminary assessment of new or performance evaluation of existing subsurface flow constructed wetland systems. The validity of this methodology is checked with data from existing systems and is found to be quite satisfactory. This methodology is combined with simple equations predicting the maximum wetland capacity in summer, so as to assist designers in sizing installations in tourist areas with increased summer populations. Furthermore, based on this methodology, a sensitivity analysis is performed of the area requirements for wastewaters of various strengths and various design conditions and performance criteria. The results provide a useful overview to engineers and further simplify the design methodology of new subsurface flow constructed wetland systems.     

变长线扫描选择性激光烧结快速成型工艺的质量和效率优势分析

本文分析变长线扫描选择性激光烧结快速成型工艺对点扫描工艺的质量和效率优势.对二者光学系统结构作分析对比,对焦斑和线束上的功率密度作计算对比.变长线扫描系统采用的扫描方式和聚焦元件使线束宽度小且恒定,线束功率密度与点扫描焦斑的相当.变长线扫描选择性激光烧结快速成型工艺的质量优势是明显的,效率比点扫描工艺提高一倍左右.     

矿山岩土工程系统环境质量评价指标体系

矿山现行的环境影响评价及其提交的环境影响报告书,是将矿山开发视为单个建设项目且只注重污染物排放和简单数量分析的单要素评价.本文将矿山开发视为统一系统,充分考虑系统内矿石开采、废石场、尾矿库等岩土工程及其矿岩氧化淋滤产生的毒害物质对矿区及其区域水土环境潜在而长期的影响,建立矿山岩士工程系统环境质量评价的指标体系,以改变矿山环境评价的传统旧式,规范和监督矿山开采行为,实现矿业开发与环境保护的协调发展.     

大窝山隧道进口围岩快速掘进施工组织与管理

结合工程概况及工程特点,从机械设备配置、劳动力组织、现场管理等方面介绍了大窝山隧道进口Ⅱ级,Ⅲ级围岩段的快速掘进施工组织与管理措施,为类似隧道的快速掘进施工组织与管理提拱了相关经验.     

基于ANSYS有限元分析深水墩施工技术研究

介绍了丹江口二桥深水墩基础施工平台的设计，重点介绍利用ANSYS通用有限元程序对施工平台的施工过模拟分析，以及对分析结果的总结。