Effect of temperature and retention period on biogas production from lignocellulosic material

The extensive utilization of biogas for energy needs of rural dwellers would reduce their dependence on fossil fuels and fuelwoods and henoe camplement Government afforestation programes. In this investigation, effect of temperature and retention period on biogas production from lignooellulosic material, hereafter referred to as cow dung were studied. Maximum gas production was dotained at thermophilic temperature. The results of the effect of retention period shows that gas production was qotimum at 4th and 7th weeks of production.     

Biaxiale Ermüdung reibrührgeschweißter Strukturelemente

Biaxial fatigue of friction stir welded stiffened panels Within the framework of the European WelAir project, cruciform specimens made from stiffening FSW overlap joints were fatigued in the DLR biaxial test rig. To resemble the loading situation of pressurized fuselage structures, proportional loading without any phase shift, but with different load ratios λ between the loading components in both directions was applied.Natural crack initiation and subsequent crack growth were governed by the stiffness gradient caused by introducing the stringer. Cracks initiated and propagated at run‐in and run‐out locations in a direction perpendicular to the weld seam. The shortest fatigue life was observed for uniaxial loading in welding direction (λ = 0). An additional stress component perpendicular to the joint line (λ > 0) resulted in a higher number of cycles to failure. Similar to single stringer panels, increasing the load ratio also increased the number of cycles to failure for FSW clip‐stringer structural members, but additionally gives a different location of the fatal crack.     

Ermüdungsverhalten und Dauerfestigkeit von Graphit und Aluminium – infiltriertem Graphit

Fatigue behaviour and endurance limit of graphite and of aluminium‐infiltrated graphite Fatigue properties of polycrystalline, isotropic graphite FU2590 and of FU2590 infiltrated with AlSi7Mg (FU2590/AlSi7Mg) were investigated in reversed bending tests at 25 Hz at numbers of cycles below 10⁷ and in tension‐compression tests at 20 kHz below 10⁹ cycles. The open porosity of Graphite (10‐11 Vol.‐%) was infiltrated with the aluminium alloy using the squeeze casting infiltration method, which led to an increase of the bending strength by 50 %, increase of tensile strength by 30 % and increase of stiffness by 15 %. Fully reversed tension‐compression loading of FU2590 delivers a mean endurance limit at 10⁹ cycles at the normalized maximum stresses (i.e. maximum tension stress of a cycle divided by the static strength) of 0,65±0,03. Mean numbers of cycles to failure of 10⁴ were found in fully reversed bending tests at the normalized maximum stress of 0,78. The infiltrated material shows approximately 30 % higher cyclic strength in reversed bending tests, and the mean endurance limit under tension compression loading increases by 15 %. The increased endurance limit of the infiltrated material is caused by the increased stiffness. The increased toughness of graphite due to the infiltration with aluminium is of additional beneficial influence at the higher cyclic stresses investigated in reversed bending tests and in static tests.     

Dynamic fatigue behaviour of a steatite ceramic

Dynamic fatigue of a low dielectric loss steatite was investigated. To this end, the values of n and B, the so‐called subcritical crack growth (SCG) parameters were experimentally determined. The steatite exhibited the expected dynamic fatigue behaviour, so that the stress corrosion susceptibility parameter, n, of 24 was obtained. In addition, the material/environment parameter B, which is a constant for a given test environment, was also attained. These parameters are instrumental in predicting the lifetime of components under stress. When the applied load is such that the resulting strength equals half of the inert strength (σ_i), defined as the strength of a sample tested in an inert environment or at a fast stress rate, i.e. where no subcritical crack growth occurs, the time to failure (t_f) of the material was found to be ～140 h. Measurement of the fracture toughness of steatite is also of upmost importance and so it was determined using three test methods. A value of K_Ic = 1.91 ± 0.29 MPa m^1/2 was attained by the indentation fracture method through measurement of the cracks emanating from the Vickers indentation. This value is in good agreement with those determined using the K_Isc (surface crack in flexure) test method (2.21 ± 0.07 MPa m^1/2) and fractography analysis test method (2.00 ± 0.44 MPa m^1/2). Differences in test procedure and analysis causing the values from each test method to be different are discussed.     

Enhanced assessment of ageing phenomena in steel structures based on materials data and non‐destructive testing

The increasing amount of ageing civil steel infrastructure requests an enhanced assessment of this infrastructure in terms of determining its residual fatigue life in a more realistic way than this has been done in the past. Often the relevant materials data for cyclic loading of such an ageing infrastructure is not available and its retrieval turns out to be relatively cumbersome bearing the urgency in data availability and continuous cost pressure in mind. This article addresses different approaches and techniques on how materials data for cyclic loading can be obtained at a fraction of the effort compared to state‐of‐the‐art techniques, considering load increase tests, non‐destructive testing techniques and finally even a stepped bar specimen allowing a complete set of materials data (stress‐strain behaviour and stress‐ and strain‐life curve) to be obtained with a single specimen in the end only. Options for ’digitizing’ materials data evaluation are discussed and some prospect on application of those novel approaches and techniques in damage accumulation assessments on real steel infrastructure is provided.     

Design of a Medical Non‐Linear Drilling Device: The Influence of Twist and Wear on the Fatigue Behaviour of NiTi Wires Subjected to Bending Rotation

This paper considers fundamental and experimental aspects associated with the engineering design of a medical, non‐linear drilling device which exploits shape memory pseudoelasticity of NiTi wires. For this application it is important that the NiTi wires have a good fatigue resistance. This is why the present authors have previously determined the influence of various parameters on cyclic life, crack growth and stress state of pseudoelastic wires subjected to bending rotation fatigue. The actual drilling device has to withstand twist in addition to bending rotation because the free rotation is constrained by friction between the drill head and the bone material. In addition, friction between the wire and a NiTi guiding tube results in wear and this may well promote fatigue crack nucleation. In this paper, we explain the function of the medical drill. We then report results on the effect of the additional parameters (1) twist and (2) wear on the fatigue life of thin pseudoelastic NiTi wires. We finally discuss the implications of our experimental results for the design process of the medical drilling device.     

蜣螂优化算法在 Canny 边缘检测算法中的应用

针对传统 Canny 边缘检测需要手动选取阈值以及不能有效提取边缘轮廓的问题,提出了一种基于改进的蜣螂优化算 法(DBO) 来优化 Canny 算子的边缘检测算法。首先通过快速引导滤波代替传统高斯滤波对图像进行保边去噪;其次用4方 向的 Sobel 模板来计算图像的梯度幅值和梯度方向;最后利用蜣螂优化算法优化的二维大津法自适应获取高低阈值。针对蜣 螂优化算法种群多样性不强问题,提出用 tent 映射初始化种群;为了提高算法跳出局部最优的能力,采用精英差分变异策略 对最优蜣螂个体进行变异扰动。实验结果表明,在边缘准确度和连接性上,该算法与传统 Canny 边缘检测算法对比有一定程 度的提升,能够有效提取图像的边缘轮廓,提高了Canny 边缘检测的边缘连接性,具有一定的实用性。