钢管套筒灌浆连接轴向受拉性能模拟试验研究

为研究钢管套筒灌浆连接轴向受拉破坏过程及破坏机理，试验中设计了16组48个钢管套筒灌浆连接试件，试件采用钢板代替圆钢管，并进行静载试验。分析了灌浆料裂缝扩展过程、荷载-相对位移曲线，并对抗剪键高距比、灌浆料厚度、侧向力等因素对破坏过程及承载力的影响进行分析。结果表明：对于不设置抗剪键的套筒灌浆连接试件，斜裂缝随机产生，裂缝分布不均匀；对于设置抗剪键的套筒灌浆连接试件，裂缝首先出现在底部抗剪键位置处，与水平方向夹角约为30°，随后在中部和上部抗剪键位置处分别出现斜裂缝。由于每个抗剪键上荷载分担并不均匀，与抗剪键接触的灌浆料逐渐达到极限压应力，达到极限状态时，承载力全部由抗剪键间的机械咬合力承担，在连接承载力中，可忽略摩擦力和胶结力作用。随着抗剪键高距比h/s增大，各试件初始剪切刚度相差不大，承载力增大，但增幅逐渐减小，建议抗剪键高距比0.06g/s>0.3，同时需要满足灌浆料灌注的施工要求。     

继电保护中多路模拟量采集系统的设计

介绍了一种基于高性能浮点DSP芯片TMS320C32、CPLD芯片XC95288和A/D采样芯片AD976组成的多路采集系统的工作原理以及设计方法。通过对第一路施加特殊的电压量,在CCS开发环境下读取采样缓冲区的值,并利用Matlab对采样数据进行了全波傅氏变换。此外,该系统已在继电保护中得到广泛应用,实践表明,该系统能较好地解决多路模拟量的采集,并确保了采样数据的安全可靠性。     

Bearing Failure Optimization of Composite Double-Lap Bolted Joints Based on a Three-Step Strategy Marked By Feasible Region Reduction and Model Decoupling

To minimize the mass and increase the bearing failure load of composite doublelap bolted joints, a three-step optimization strategy including feasible region reduction, optimization model decoupling and optimization was presented. In feasible region reduction, the dimensions of the feasible design region were reduced by selecting dominant design variables from numerous multilevel parameters by sensitivity analyses, and the feasible regions of variables were reduced by influence mechanism analyses. In model decoupling, the optimization model with a large number of variables was divided into various sub-models with fewer variables by variance analysis. In the third step, the optimization sub-models were solved one by one using a genetic algorithm, and the modified characteristic curve method was adopted as the failure prediction method. Based on the proposed optimization method, optimization of a double-lap single-bolt joint was performed using the ANSYS^® code. The results show that the bearing failure load increased by 13.5% and that the mass decreased by 8.7% compared with those of the initial design of the joint, which validated the effectiveness of the three-step optimization strategy.     

乐滩灌区输水隧洞穿合山煤矿采空区处理设计

分析了乐滩灌区工程北干渠溯河隧洞段长约1.06 km穿合山煤矿采空区的地质情况.借鉴高速公路煤矿采空区的成功处理经验,通过科学分析,对采空区变形和区域内覆岩的稳定性做了评价,论述了输水线路穿采空区段采取全充填压力注浆法的工程处理方法.     

A Lattice Approach to Image Segmentation

After a formal definition of segmentation as the largest partition of the space according to a criterion σ and a function f, the notion of a morphological connection is reminded. It is used as an input to a central theorem of the paper (Theorem 8), that identifies segmentation with the connections that are based on connective criteria. Just as connections, the segmentations can then be regrouped by suprema and infima. The generality of the theorem makes it valid for functions from any space to any other one. Two propositions make precise the AND and OR combinations of connective criteria. The soundness of the approach is demonstrated by listing a series of segmentation techniques. One considers first the cases when the segmentation under study does not involve initial seeds. Various modes of regularity are discussed, which all derive from Lipschitz functions. A second category of examples involves the presence of seeds around which the partition of the space is organized. An overall proposition shows that these examples are a matter for the central theorem. Watershed and jump connection based segmentations illustrate this type of situation. The third and last category of examples deals with cases when the segmentation occurs in an indirect space, such as an histogram, and is then projected back on the actual space under study. The relationships between filtering and segmentation are then investigated. A theoretical chapter introduces and studies the two notions of a pulse opening and of a connected operator. The conditions under which a family of pulse openings can yield a connected filter are clarified. The ability of segmentations to generate pyramids, or hierarchies, is analyzed. A distinction is made between weak hierarchies where the partitions increase when going up in the pyramid, and the strong hierarchies where the various levels are structured as semi-groups, and particularly as granulometric semi-groups. The last section is based on one example, and goes back over the controversy about “lattice” versus “functional” optimization. The problem is now tackled via a case of colour segmentation, where the saturation serves as a cursor between luminance and hue. The emphasis is put on the difficulty of grouping the various necessary optimizations into a single one.     

开关电源的平均电流自动均流技术

针对多个开关电源并联时易出现负载电流在各模块间分配不均的现象,介绍了常用的负载电流自动均流法——平均电流自动均流法及其工作特性。并针对其存在母线电压降低的缺陷,提出了一种改进的平均电流自动均流方法,经试验证明均流精度比较高。     

Evaluation of performance enhancing proxies in internet over satellite

Performance enhancing proxies (PEPs) are widely used to improve the performance of TCP over high delay‐bandwidth product links and links with high error probability. In this paper we analyse the performance of using TCP connection splitting in combination with web caching via traces obtained from a commercial satellite system. We examine the resulting performance gain under different scenarios, including the effect of caching, congestion, random loss and file sizes. We show, via analysing our measurements, that the performance gain from using splitting is highly sensitive to random losses and the number of simultaneous connections, and that such sensitivity is alleviated by caching. On the other hand, the use of a splitting proxy enhances the value of web caching in that cache hits result in much more significant performance improvement over cache misses when TCP splitting is used. We also compare the performance of using different versions of HTTP in such a system. Copyright © 2003 John Wiley & Sons, Ltd.     

CFH-Ⅱ型翻车机传动齿轮轴承座的座脚螺栓联接失效分析与改进

分析了CFH-Ⅱ型翻车机传动齿轮轴承座的座脚螺栓组联接失效(松动)的原因，得出控制和保证合适的螺栓组联接预紧力是防止螺栓联接失效(松动)的关键；依据现场条件，对座脚螺栓进行了设计改进；提出了一种适合现场使用的螺栓预热伸长的装配方法，经实践验证此法是简单可靠的装配方法。     

3D velocity from 3D Doppler radial velocity

We present local least squares and regularization frameworks for computing 3D velocity (3D optical flow) from 3D radial velocity measured by a Doppler radar. We demonstrate the performance of our algorithms quantitatively on synthetic radial velocity data and qualitatively on real radial velocity data, obtained from the Doppler radar at Kurnell Radar station, Botany Bay, New South Wales, Australia. Radial velocity can be used to predict the future positions of storms in sequences of Doppler radar datasets.© 2005 Wiley Periodicals, Inc. Int J Imaging Syst Technol, 15, 189–198, 2005     

欠驱动系统Pendubot的模糊控制策略

本文针对欠驱动Pendubot机器人系统，提出一种简单可靠的摇起及平衡控制策略。通过利用模糊控制及全状态反馈控制技术来分别设计摇起控制器及平衡控制器，其中模糊摇起控制器的设计使得系统的摇起可靠性得到大大的加强，并缩短了响应时间，两个控制器的转换通过转换装置实现。最后的仿真结果验证了算法的有效性。