恢复地层剥蚀厚度方法综述

恢复地层剥蚀厚度是对盆地进行定量研究的重要基础工作。本文综述、评价了目前常用的恢复剥蚀厚度的方法,并对作者曾提出的天然气平衡浓度法作了进一步的阐述。     

Influence of process variables on the drying of potato slices

Investigation of the effects of varying air velocity, slice thickness, and pre-treatment with sodium chloride solutions and surface active agents on drying potato slices indicated that the drying occurred entirely in the falling rate period and was controlled by the mechanism of liquid diffusion. The rate of drying, and therefore the diffusion coefficients, increased with the addition of sodium chloride and surface active agents. Diffusion coefficients were also influenced by air velocity and slice thickness, suggesting that the rate of drying of potato slices is controlled by a combination of internal and external resistances.     

Emission Of Volatile And Semivolatile Organic Compounds From Waterborne Paints – The Effect Of The Film Thickness

A waterborne paint was applied to tin plated steel sheets with three different film thicknesses. The emission of volatile and semivolaile organic compounds ((S) VOCs) from the samples was measured in small climatic chambers under standard conditions over a two-week period. The purpose of the study was to evaluate the effect of the film thickness on the emission rate decay. First order decay models, including sink effects for the high boiling (S) VOCs, were fitted to the concentration versus time data. The results showed that the first order rate constants decrease with increasing film thickness. In uddition, the results indicated that the emissions of the (S)VOCs in the waterborne paint film seemed to be controlled by evaporation. The thicknesses of paint films used in climatic chamber tests to estimate emission rates for product compurison or emission prediction must be known in order to prevent erroneous conclusions     

钢管在线测厚和应用

钢管在线测厚是近年发展较快的一项高科技技术，该设备对生产高质量的无缝钢管具有较大帮助。叙述了钢管在线测厚的基本原理和在宝钢钢管分公司张减机上使用的实绩。     

四辊铝箔轧机预控参数在线整定

介绍Ф210mm/Ф500mm× 800mm四辊液压轧机厚度预控系统中采用人机界面实现参数在线调整的方法,能大大提高预控参数的控制精度,减少轧机产品的厚度误差,是厚度自动控制的一项创新.     

K_2O－CaO－Al_2O_3－SiO_2系统自释釉瓷化学组成的研究

本文从酸度系数着手，证实了Ｋ２Ｏ－ＣａＯ－Ａｌ４Ｏ久－ＳｉＯ２系统中存在自释釉组成，限定了其组成范围，０．６７％＜Ｋ２Ｏ＜１．２８％，１０．６４％＜ＣａＯ＜１３．６２％，１１．５３％＜Ａｌ４Ｏ３＜１５．３２％，７２．７３％＜ＳｉＯ２＜７４．０４％，并讨论了自释釉瓷的性能。     

换热器管板厚度的快速计算

在化工生产中，换热器设备是应用最广泛的一种设备，且占主导地位。而在换热器设计过程中，管板厚度设计计算比较复杂。本文的特点是在满足GB151—1999《管壳式换热器》标准要求的前提下，介绍一种快速简便估算管板厚度的计算公式，从而达到快速确定管板厚度的目的。     

An Experimental Study of Fatigue Strength for Adhesively Bonded Tubular Single Lap Joints

In this paper, manufacturing technology of the tubular single lap adhesive joint was studied to obtain reliable and optimal joint quality. In addition, a surface preparation method and a bonding process for the joint were devised. The effect of the adhesive thickness and the adherend roughness on the fatigue strength of the joint was experimentally investigated. From experiments, it has been found that the fatigue strength of the joint increased as the adhesive thickness decreased and the optimal arithmetic surface roughness of the adherends was about 2 μm.     

胶层厚度对拉伸试样应力分布影响的数值分析

运用弹塑性有限元法研究了胶层厚度对承受拉伸载荷的对接接头胶层内应力分布的影响．三维有限元法数值分析的结果表明，随胶层厚度减小，胶层中正应力SZ与剪应力SYZ的分布趋于均匀；而对正应力SY而言，胶层厚度为0．15mm时，其边缘峰值应力最低。     

Corner forming of AZ61A magnesium alloy tube within warm hydroforming

The corners with small radii on cross sections are crucial for forming hydroformed components with polygonal sections.In this paper,warm hydroforming experiments of AZ61A magnesium alloy tubes were carried out to study the forming regularity of round corners by using a demonstration part with square sections.Effects of temperature on radius forming,thinning ratio distribution and microstructure were revealed and a component with relative outer corner radius of 3.0 was obtained by warm hydroforming at 240℃.The minimum thickness of the formed square section was located in the transition position between the corner and the straight wall.The thinning ratio of the round corner increased with the increase of forming temperature.Formability of the magnesium tube was improved by raising temperature under the effect of dynamic recrystallization at 240℃.