Hydraulic reactivity and cement formation of baghdadite

In this study, the hydraulic reactivity and cement formation of baghdadite (Ca₃ZrSi₂O₉) was investigated. The material was synthesized by sintering a mixture of CaCO₃, SiO₂, and ZrO₂ and then mechanically activated using a planetary mill. This leads to a decrease in particle and crystallite size and a partial amorphization of baghdadite as shown by X-ray powder diffraction (XRD) and laser diffraction measurements. Baghdadite cements were formed by the addition of water at a powder to liquid ratio of 2.0 g/ml. Maximum compressive strengths were found to be ~2 MPa after 3-day setting for a 24-h ground material. Inductively coupled plasma mass spectrometry (ICP-MS) measurements showed an incongruent dissolution profile of set cements with a preferred dissolution of calcium and only marginal release of zirconium ions. Cement formation occurs under alkaline conditions, whereas the unground raw powder leads to a pH of 11.9 during setting, while prolonged grinding increased pH values to approximately 12.3.     

A novel quasi-oppositional harmony search algorithm and fuzzy logic controller for frequency stabilization of an isolated hybrid power system

The intermittent wind power in isolated hybrid distributed generation (IHDG) may cause serious problems associated with frequency (f) and power (P) fluctuation. Energy storage devices such as battery, super capacitor, and superconducting magnetic energy storage (SMES) may be used to reduce these fluctuations associated with f and P. This paper presents a study of IHDG power system for improving both f and P deviation profiles with the help of SMES. The studied IHDG power system is consisted of wind turbine generator and diesel engine generator. Both f and P control problems of the studied power system model are addressed in presence or absence of SMES. Fuzzy logic based proportional–integral–derivative (PID) controller with SMES is used for the purpose of minimization of f and P deviations. The different tunable parameters of the PID controller and those of the SMES are tuned by a novel quasi-oppositional harmony search algorithm. Performance study of the IHDG power system model is carried out under different perturbation conditions. The results demonstrate minimum f and P deviations may be achieved by using the proposed fuzzy logic based PID controller along with SMES.     

构皮滩水电站泄洪洞优化设计

构皮滩水电站为满足2008年12月工程提前发电的需要,结合现有泄洪洞地质情况和施工情况对泄洪洞布置进行了专题研究,结果表明利用降低进口高程为550 m的泄洪洞和坝身放空底孔联合参与后期导流,可缓解2007年导流隧洞下闸封堵后大坝在2008年汛期施工的压力,为大坝施工增加了2个月左右的工期。     

An overlapping domain decomposition dual reciprocity method

We present a domain decomposition boundary integral equation method for two-dimensional partial differential equations. The overlapping Schwarz method is employed to improve the dual reciprocity boundary element method. The resulting algorithm turns out to be more accurate than a non-overlapping approach previously proposed. Some numerical results showing the improved accuracy and efficiency of the methods are given.     

基于积分原理的低功耗超声波流量检测方法

文章通过对时差式超声波流量检测方法的分析，提出了基于过零检测技术及积分法的信号处理方法，避免了繁琐的信号处理，降低了整机功耗。结合工作时序的设计，提出了实现低功耗超声波液体流量检测的措施。     

水力射孔对套管强度的影响研究

水力射孔技术是一种新型的完井方式，深穿透水力射孔技术辅助定向水力压裂可以实现油气层改造和油气井增产。但是，水力射孔套管会在孔眼处造成应力集中，使得局部应力过大而削弱了套管和水泥环的强度，可能会影响套管的使用寿命。因此，文章利用有限元软件建立了射孔套管的三维有限元模型，分析了水力射孔后套管管体的应力分布，重点研究了水力射孔参数-孔密、孔径、孔深、射孔方位角等对套管强度的影响规律。分析结果表明，沿着最大水平地应力方向深穿透水力射孔，选择合适的孔密、孔径可将射孔对套管的损害降至最小。研究结果为提高水力射孔完井设计水平提供了一定的参数依据。     

非稳定井流模型的半解析解

为了提高非稳定渗流计算的计算精度 ,通过数学分析得到了水位传导系数随时间变化时 ,一类非稳定渗流井流模型的半解析解 ,并进行了计算比较     

A note on the Gauss-Jacobi quadrature formulae for singular integral equations of the second kind

A fast and efficient numerical method based on the Gauss-Jacobi quadrature is described that is suitable for solving Fredholm singular integral equations of the second kind that are frequently encountered in fracture and contact mechanics. Here we concentrate on the case when the unknown function is singular at both ends of the interval. Quadrature formulae involve fixed nodal points and provide exact results for polynomials of degree 2n − 1, where n is the number of nodes. Finally, an application of the method to a plane problem involving complete contact is presented.     

低温低渗透砂岩油藏窜流大孔道深部封堵技术研究

所用堵剂为高强度的淀粉接枝聚丙烯酰胺交联凝胶SAMG-1,由<6%淀粉、4.5%-5.5%丙烯酰胺、0.003%-0.006%交联剂组成,35℃成胶时间受淀粉和交联剂用量控制,为18-20小时以上,成胶前黏度-100 mPa.s。该堵剂具有长期稳定性,在储层岩心中注入深度15 cm的堵剂,在35℃候凝48小时后及老化90天后,封堵强度分别为0.61和0.59 MPa/cm,封堵率分别为98.6%和98.1%。该堵剂优先进入高渗层,注入0.5 PV并成胶后,2组双填砂管组成的模型低、高渗管渗透率保留率分别为68.4%、0.7%和69.4%、0.0%。吉林扶余油田西一区+15-8.2区块有水井6口,油井13口,含水率达91.5%,注入水最快在5天内到达油井。报道了该区块整体深部调剖封堵窜流通道的情况,详细叙述了+15-9.2井施工中通过注入压力和井底回压控制注入流量,使堵剂陆续进入原生和次生孔道的工艺作业,该井设计注入堵剂92 m3。6口水井整体调剖后,油井产液量差别减小,产油量增加,有效期已超过了9个月,共增油843 t,含水平均下降3.87%。图7表1参8。     

液力联轴器喷油着火事故的原因分析及预防

以矿用液力联轴器为研究对象 ,阐明其喷油着火的机理 ,分析其喷油着火的原因并作出事故树分析 ,针对现场使用的情况 ,提出预防措施及发展趋势 ,对矿井安全生产具有指导性作用。