大口径光学元件装夹转运结构设计及分析

为了实现大口径光学元件的安全装夹、转运,通过光学元件开槽与不开槽两种装夹方式的分析,得出开槽夹紧转运方式将带来微裂纹、应力集中、成本高等缺陷,提出了利用摩擦力克服光学零件的重力和惯性力的低应力装夹转运方案。通过对光学元件低应力夹紧结构设计,并利用有限元分析方法,得到不开槽装夹方式下,光学元件的最大主应力为1.11 MPa,最大切应力为0.73 MPa,远低于光学元件破坏的强度极限,且受力均匀,无应力集中现象。     

基于新型光纤的传输技术探讨

随着互联网的高速发展，引发了网络流量、电信骨干网流量急速增长，使得网络容量的提升迫在眉睫。目前，100G 系统已经商用，超100G系统能够更有效地解决流量和网络带宽持续增长带来的压力，本文主要介绍新型单模光纤的特性以及探讨基于新型单模光纤的传输技术。     

综放工作面防治水技术应用实践

为解决21000工作面采空区及顶板涌水问题,根据工作面出水点的不同情况,采取了集水器导水、老塘设挡水堰截水、挖排水沟疏水等多项治水措施,经统计排水量达33~42m3/h,有效控制了水情,确保了工作面正常生产。     

空间红外大口径折射式低温镜头设计与验证

针对目标探测类空间红外相机大范围成像、高灵敏度探测、高精度定位等应用需求,文中提出采用像方远心光路和低温光学技术结合的解决方案,设计了物方视场角8°×8°、入瞳口径265 mm、工作温度200 K的像方远心折射式光学系统。镜头最大口径280 mm,采用多级分散的弹性支撑设计,解决大口径低温透镜装框、透镜组件支撑和镜头整体安装各环节的热应力卸载问题。在保证高刚度和低漏热的情况下,使低温下透镜的热应力对镜头能量集中度的影响降低到可接受范围内。镜头完成装调及室温下像质确认后,进行了力学振动试验,并将其制冷到200 K水平测试像质,测试结果表明,镜头能量集中度达到轴上75%,边缘视场72%。     

四川南桠河一期工程姚河坝水电斜井开挖施工技术浅论

以姚河坝水电站引水隧洞50°倾角、长度为194.734m的斜井开挖为实例,从施工测量、开挖方法、通风防尘、临时支护斜井及安全施工等方面探讨长洞身、大倾角斜井在无爬罐条件下的人工开挖方法.     

企业不但应该做大更应该做强

从入世的角度 ,分析了我国企业在重组过程中存在的问题 ,并指出了我国企业做强做大的紧迫性     

A new iterative order reduction (IOR) method for eigensolutions of large structures

Order reduction is a computationally efficient method to estimate some lowest eigenvalues and the corresponding eigenvectors of large structural systems by reducing the order of the original model to a smaller one. But its accuracy is limited to a small range of frequencies that depends on the selection of the retained degrees of freedom. This paper proposes a new iterative order reduction (IOR) technique to obtain accurately the eigensolutions of large structural systems. The technique retains all the inertia terms associated with the removed degrees of freedom. This hence leads to the reduced mass matrix being in an iterated form and the reduced stiffness matrix constant. From these mass and stiffness matrices, the eigensolutions of the reduced system can be obtained iteratively. On convergence the reduced system reproduces the eigensolutions of the original structure. A proof of the convergence property is also presented. Applications of the method to a practical GARTEUR structure as well as a plate have demonstrated that the proposed method is comparable to the commonly used Subspace Iteration method in terms of numerical accuracy. Moreover, it has been found that the proposed method is computationally more efficient than the Subspace Iteration method. Copyright © 2003 John Wiley & Sons, Ltd.     

排汽屋面施工——探讨屋面防水施工的一种新方法

探讨了采用排汽屋面的施工方法解决屋面渗水的问题。     

Prediction of the energy dissipation rate in ductile crack propagation

In this paper, energy dissipation rate D vs. Δa curves in ductile fracture are predicted using a ‘conversion’ between loads, load‐point displacements and crack lengths predicted by NLEFM and those found in real ELPL propagation. The NLEFM/ELPL link was recently discovered for the DCB testpiece, and we believe it applies to other cracked geometries. The predictions for D agree with experimental results. The model permits a crack tip toughness R(Δa) which rises from J_c and saturates out when (if) steady state propagation is reached after a transient stage in which all tunnelling, crack tip necking and shear lip formation is established. J_R is always greater than the crack tip R(Δa) and continues to rise even after R(Δa) levels off. The analysis is capable of predicting the usual D vs. Δa curves in the literature which have high initial values and fall monotonically to a plateau at large Δa. It also predicts that D curves for CCT testpieces should be higher than those for SENB/CT, as found in practice. The possibility that D curves at some intermediate Δa may dip to a minimum below the levelled‐off value at large Δa is predicted and confirmed by experiment. Recently reported D curves that have smaller initial D than the D‐values after extensive propagation can also be predicted. The testpiece geometry and crack tip R(Δa) conditions required to produce these different‐shaped D vs. Δa curves are established and confirmed by comparison with experiment. The energy dissipation rate D vs. Δa is not a transferable property as it depends on geometry. The material characteristic R(Δa) may be the ‘transferable property’ for scaling problems in ELPL fracture. How it can be deduced from D vs. Δa curves (and by implication, J_R vs. Δa curves) is established.