Benchmark experiment of large-angle scattering reaction cross section of iron at 14 MeV using two shadow bars – Comparison of experimental results with ENDF/B-VIII –

ABSTRACT

It is important to perform neutron transport simulations with accurate nuclear data in the neutronics design of a fusion reactor. However, absolute values of large-angle scattering cross sections vary among nuclear data libraries even for well-examined nuclide of iron. Benchmark experiments focusing on large-angle scattering cross sections were thus performed to confirm the correctness of nuclear data libraries. The series benchmark experiments were performed at a DT neutron source facility, OKTAVIAN of Osaka University, Japan, by the unique experimental system established by the authors’ group, which can extract only the contribution of large-angle scattering reactions. This system consists of two shadow bars, target plate (iron), and neutron detector (niobium). Two types of shadow bars were used and four irradiations were conducted for one experiment, so that contribution of room-return neutrons was effectively removed and only large-angle scattering neutrons were extracted from the measured four Nb reaction rates. The obtained experimental results were compared with calculations for five nuclear data libraries including JENDL-4.0, JEFF.-3.3, FENDL-3.1, ENDF/B- VII, and recently released ENDF/B-VIII. It was found from the comparison that ENDF/B-VIII showed the best result, though ENDF/B-VII showed overestimation and others are in large underestimation at 14 MeV.     

Effect of an abrupt change in pulling rate on microstructures of directionally solidified Al2O3-Er3Al5O12 eutectic and off-eutectic composite ceramics

Directionally solidified microstructures of Al₂O₃-Er₃Al₅O₁₂ eutectic and off-eutectic in situ composite ceramics were explored under abrupt-change pulling rate conditions. Corresponding temperature distributions and interface locations were studied. In eutectic composition, fluctuation of eutectic spacing occurred when the pulling rate increased abruptly. A gradually increase or abrupt increase in eutectic spacing was observed when the pulling rate decreased abruptly. In hypoeutectic and hypereutectic compositions, formation of the primary phases were suppressed when the pulling rate increased abruptly from 10?µm/s to 100?µm/s, while primary phases precipitated when the pulling rate decreased abruptly from 100?µm/s to 10?µm/s. The interface altitude decreased after the pulling rate increased abruptly, but increased after the pulling rate decreased abruptly. The liquid composition restriction (around the eutectic composition) at the eutectic interface plays an important role in the suppression of the primary dendrite and coupled eutectic oxides can be obtained in off-eutectic compositions even under higher solidification rate conditions.     

Compressive properties of pristine and SiC-Te-added MgB2 powders,green compacts and spark-plasma-sintered bulks

Pristine and (SiC+Te)-added MgB₂ powders, green and spark plasma sintered (SPS) compacts were investigated from the viewpoint of quasi-static and dynamic (Split-Hopkinson Pressure Bar, SHPB) compressive mechanical properties The amount of the additive (SiC+Te) was selected to be the optimum one for maximization of the superconducting functional parameters. Pristine and added MgB₂ show very similar compressive parameters (tan δ, fracture strength, Vickers hardness, others) and fragment size in the SHPB test. However, for the bulk SPSed samples the ratio of intergranular to transgranular fracturing changes, the first one being stronger in the added sample. This is reflected in the quasi-static K_IC that is higher for the added sample. Despite this result, sintered samples are brittle and have roughly similar fragmentation behavior as for brittle engineering ceramics. In the fragmentation process, the composite nature of our samples should be considered with a special focus on MgB₂ blocks (colonies) that show the major contribution to fracturing. The Glenn-Chudnovsky model of fracturing under dynamic load provides the closest values to our experimental fragment size data.     

土壤冲击特性的实验研究

本文利用分离式Hopkinson压杆研究了土体在不同应变率条件下的冲击动态力学性能，发现土体有明显的应变率效应，与静载相比，冲击荷载下土的动强度和动模量均有很大的提高。     

On the determination of optimal transition profile of a stepped bar in tension or in torsion by BEM

The objective is to have uniformly distributed tangential stresses on the transition profile of a stepped bar subjected to tensile and torsional loading using an axisymmetric boundary element formulation. The transition curve is represented by the Langragian interpolation polynomial with progressive degrees to avoid shape distortion during the optimization procedure. The calculated result is compared with that obtained by fluid dynamics given in the literature. It is seen that the transition curve obtained in this paper is reasonable.     

先张法预应力桥梁板施工工艺及应用实例

结合太原市向阳店桥梁板施工实例，介绍了采用先张法进行预应力桥梁板施工的过程。阐述了桥梁板的施工工艺，该工艺实现了整体张拉、整体放张，使钢绞线逐根受力均匀，施工速度快，能保证梁端的质量。指出拉杆系统的使用，降低了成本，增加了效益。     

挡渣球和挡渣塞技术在转炉炼钢的应用

介绍了档渣球和挡渣塞技术在转炉炼钢的实际应用，有利于降低原材料消耗、增加企业效益。     

植筋施工工艺

以某网球馆改造工程为例 ,就植筋技术的概念及所用材料进行了介绍 ,详细阐述了其施工工艺流程及措施 ,指出植筋技术具有工艺简单、操作方便、造价相对较低等优点     

硬质合金长条薄片弯曲变形的控制

从毛坯厚度差、装舟方式、冷却速度、舟皿涂料等方面分析了YG8和J12硬质合金长条薄片的弯曲变形原因,提出了几种抑制弯曲变形的措施。