Structural health monitoring system based on multi-agent coordination and fusion for large structure

In practical applications of structural health monitoring technology, a large number of distributed sensors are usually adopted to monitor the big dimension structures and different kinds of damage. The monitored structures are usually divided into different sub-structures and monitored by different sensor sets. Under this situation, how to manage the distributed sensor set and fuse different methods to obtain a fast and accurate evaluation result is an important problem to be addressed deeply. In the paper, a multi-agent fusion and coordination system is presented to deal with the damage identification for the strain distribution and joint failure in the large structure. Firstly, the monitoring system is adopted to distributedly monitor two kinds of damages, and it self-judges whether the static load happens in the monitored sub-region, and focuses on the static load on the sub-region boundary to obtain the sensor network information with blackboard model. Then, the improved contract net protocol is used to dynamically distribute the damage evaluation module for monitoring two kinds of damage uninterruptedly. Lastly, a reliable assessment for the whole structure is given by combing various heterogeneous classifiers strengths with voting-based fusion. The proposed multi-agent system is illustrated through a large aerospace aluminum plate structure experiment. The result shows that the method can significantly improve the monitoring performance for the large-scale structure.     

水平岩层软弱基座危岩体演化过程研究

以重庆市甄子岩29号危岩体为研究对象，基于现场调查和分析解剖，建立UDEC离散元数值计算模型，对其演化变形过程进行模拟分析。研究表明，在巨大的自重作用下，由于基座岩体岩质软，岩体较破碎，且基座外侧为直立的陡崖，具有完整的临空面，从而使基座岩体易发生压缩流变及剪切流变，进而使危岩体存在滑移垮塌的危险。     

钢管套筒灌浆连接轴向受拉性能模拟试验研究

为研究钢管套筒灌浆连接轴向受拉破坏过程及破坏机理，试验中设计了16组48个钢管套筒灌浆连接试件，试件采用钢板代替圆钢管，并进行静载试验。分析了灌浆料裂缝扩展过程、荷载-相对位移曲线，并对抗剪键高距比、灌浆料厚度、侧向力等因素对破坏过程及承载力的影响进行分析。结果表明：对于不设置抗剪键的套筒灌浆连接试件，斜裂缝随机产生，裂缝分布不均匀；对于设置抗剪键的套筒灌浆连接试件，裂缝首先出现在底部抗剪键位置处，与水平方向夹角约为30°，随后在中部和上部抗剪键位置处分别出现斜裂缝。由于每个抗剪键上荷载分担并不均匀，与抗剪键接触的灌浆料逐渐达到极限压应力，达到极限状态时，承载力全部由抗剪键间的机械咬合力承担，在连接承载力中，可忽略摩擦力和胶结力作用。随着抗剪键高距比h/s增大，各试件初始剪切刚度相差不大，承载力增大，但增幅逐渐减小，建议抗剪键高距比0.06g/s>0.3，同时需要满足灌浆料灌注的施工要求。     

A mineralogical approach to evaluating laboratory scale acid rock drainage characterisation tests

Effective management of the risks associated with acid rock drainage (ARD) requires the ability to identify material with a potential to generate ARD reliably. With the increasing prevalence of quantitative mineralogy (Quantitative XRD, auto-SEM), opportunity exists to use mineralogy at all stages in ARD characterisation and prediction. This study uses a mineralogical approach across the head grade samples and the residues obtained under leach conditions of several common ARD characterisation tests (Acid Neutralising Capacity, Net Acid Generation), as well as the University of Cape Town (UCT) biokinetic test to evaluate the extent to which acid-neutralising minerals react. The results show the contribution of the carbonates to the acid neutralising capacity, as well as the partial dissolution of intermediate weathering silicate minerals such as chlorite and mica.     

RESERVOIR PROPERTIES OF BARREMIAN – APTIAN URGONIAN LIMESTONES,SE FRANCE,PART 1: INFLUENCE OF STRUCTURAL HISTORY ON POROSITY-PERMEABILITY VARIATIONS

Upper Barremian – Lower Aptian inner platform “Urgonian” limestones in the Mont de Vaucluse region, SE France, consist of alternating metre-scale microporous and tight intervals. This paper focuses on the influence of structural deformation on the reservoir properties of the Urgonian limestone succession in a study area near the town of Rustrel. Petrographic, petrophysical and structural data were recovered from five fully-cored boreholes, from the walls of a 100 m long underground tunnel, and from a 50 m long transect at a nearby outcrop. The data allowed reservoir property variations in the Urgonian limestones to be studied from core to reservoir scale. Eleven Reservoir Rock Types (RRTs) were identified based on petrographic features (texture, grain size), reservoir properties (porosity, permeability), and the frequency of structural discontinuities such as fractures, faults and stylolites. Tight and microporous reservoir rock types were distinguished. Tight reservoir rock types were characterised by early cementation of intergranular pore spaces and by the presence of frequent structural discontinuities. By contrast microporous reservoir rock types contained preserved intragranular microporosity and matrix permeability, but had very few structural discontinuities. Observed vertical alternations of microporous and tight rock types are interpreted to have been controlled by the early diagenesis of the Urgonian carbonates. Deformation associated with regional-scale tectonic phases, including Albian – Cenomanian “Durancian” uplift (∼105 to 96 Ma) and Pyrenean compression (∼55 to 25 Ma), resulted in the modification of the initial petrophysical properties of the Urgonian limestones. An early diagenetic imprint conditioned both the intensity of structural deformations and the associated circulations of diagenetic and meteoric fluids. Evolution of the Reservoir Rock Types is therefore linked both to the depositional conditions and to subsequent phases of structural deformation.     

Strain‐rate‐dependent mechanical properties of polypropylene separator for lithium‐ion batteries

The mechanical integrity of battery separators is critical for battery safety and durability. A comprehensive study of strain‐rate‐dependent tensile and puncture properties of a polypropylene lithium‐ion battery separator is presented here with a new model. Due to anisotropy of the polymeric membrane, tensile testing was conducted for different directions. Results showed that tensile strength and elastic modulus were increased 1000% and 500%, respectively, for different directions. It was also demonstrated that tensile strength changed 10 to 25% with strain rate (1.67 × 10^?4 to 1.67 × 10^?1 s^?1) for different directions. An equation was obtained for the first time for flow stress versus strain rate at varied tensile directions with respect to machine direction. Moreover, puncture testing was performed and it was shown that puncture strength was increased 140% with increasing strain rate from 0.25 to 250 mm min^?1. Two failure modes were also observed in puncture samples. Finally, Eyring's model was used to calculate activation enthalpy of the porous polypropylene separator. © 2020 Society of Chemical Industry     

Evolution of Local Structural Ordering and Chemical Distribution upon Delithiation of a Rock Salt–Structured Li1.3Ta0.3Mn0.4O2 Cathode

Lithium‐rich disordered rock‐salt oxides have attracted great interest owing to their promising performance as Li‐ion battery cathodes. While experimental and theoretical efforts are critical in advancing this class of materials, a fundamental understanding of key property changes upon Li extraction is largely missing. In the present study, single‐crystal synthesis of a new disordered rock‐salt cathode material, Li_1.3Ta_0.3Mn_0.4O₂ (LTMO), and its use as a model compound to investigate Li concentration–driven evolution of local cationic ordering, charge compensation, and chemical distribution are reported. Through the combined use of 2D and 3D X‐ray nanotomography, it is shown that Li removal accompanied by oxygen oxidation is correlated with the development of morphological defects such as particle cracking. Chemical heterogeneity, quantified by subparticle level distribution of Mn valence state, is minimal during Mn redox, which drastically increases upon the formation of cracks during oxygen redox. Density functional theory and bond valence sum mismatch calculations reveal the presence of local short‐range ordering in the pristine oxide, which gradually disappears along with the extraction of Li. The study suggests that with cycling the transformation into true cation–disordered state can be expected, which likely impacts the voltage profile and obtainable energy density of the oxide cathodes.     

An approach to measure infill matric suction of irregular infilled rock joints under constant normal stiffness shearing

Rock joints infilled with sediments can strongly influence the strength of rock mass. As infilled joints often exist under unsaturated condition, this study investigated the influence of matric suction of infill on the overall joint shear strength. A novel technique that allows direct measurement of matric suction of infill using high capacity tensiometers (HCTs) during direct shear of infilled joints under constant normal stiffness (CNS) is described. The CNS apparatus was modified to accommodate the HCT and the procedure is explained in detail. Joint specimens were simulated by gypsum plaster using three-dimensional (3D) printed surface moulds, and filled with kaolin and sand mixture prepared at different water contents. Shear behaviours of both planar infilled joints and rough joints having joint roughness coefficients (JRCs) of 8–10 and 18–20 with the ratios of infill thickness to asperity height (t/a) equal to 0.5 were investigated. Matric suction shows predominantly unimodal behaviour during shearing of both planar and rough joints, which is closely associated with the variation of unloading rate and volumetric changes of the infill material. As expected, two-peak behaviour was observed for the rough joints and both peaks increased with the increase of infill matric suction. The results suggest that the contribution of matric suction of infill on the joint peak normalised shear stress is relatively independent of the joint roughness.     

湘中海相浅层湘冷1井酸压工艺研究及应用

湘冷1井具有气层埋藏浅（400m-500m）、纵向上裂隙发育的特点，属低孔、低渗的含泥质灰岩致密储层。大量室内实验和研究采用“前置液酸压＋闭合酸化”工艺技术，并优选了相应降阻酸和闭合酸配方。通过酸压实现了该井工业油气流的突破，取得了明显的增产效果，为新区海相浅层气的开发探索出了一套成熟的改造增产措施。     

储层应力敏感性影响因素研究

全面分析储层应力敏感性产生的机理认为，外部因素的改变会引起储层产生应力敏感性．而储层岩石物性等内部因素对应力敏感性的强弱起决定性作用。室内岩心应力敏感性评价时．仪器与设备的精度、加载与卸载方式、实验用流体类型以及各种人为因素等都会对评价结果产生影响，其中岩心密封套在高压、高温条件下的密闭性会对实验结果产生较大影响。所以储层应力敏感性不应该从孔隙度和渗透率的高低进行简单评价，中、高渗储层和低渗储层在生产过程也都可能表现出较强的应力敏感性现象。