Evaluation of cut cell cartesian method for simulation of a hook and claw type hydrogen pump

Hook and claw pumps are used for recirculation of excess hydrogen in fuel cells. Optimization of the pump design is essential. Computational Fluid Dynamic (CFD) is an effective method for performance optimization. However, it is difficult to conduct CFD simulation because of the sharp cusp of the rotor profile. Cut cell Cartesian mesh could be the solution to handle this complex and moving geometries. The aim of this paper is to evaluate ANSYS Forte for hook and claw pumps. Firstly, the conservation accuracy of the cut cell cartesian mesh is verified using an adiabatic piston cylinder case. Then, simulation results of hook and claw type pump are compared with experimental data. Finally, simulation results of air and hydrogen are compared. The results show that the CFD simulation of hook and claw pumps using cut cell cartesian mesh could provide an efficient and effective approach for the optimization of the system.     

Theoretical study of a thermoelectric-assisted vapor compression cycle for air-source heat pump applications

This paper proposes a thermoelectric-assisted vapor compression cycle (TVCC) for applications in air-source heat pump systems which could enhance the heating capacity of the system. Performances of TVCC are calculated and then compared with that of basic vapor compression cycle (BVCC). The simulation results show that when coefficients of performance (COPs) of the two cycles are almost equal, the TVCC under maximum COP condition of the thermoelectric modules still performs better than BVCC by 13.0% in heating capacity through selecting the appropriate intermediate temperature. In addition, the TVCC can also achieve an improvement of 16.4%–21.7% in both the heating COP and capacity when compared with the BVCC with an assistant electric heater that is provided with the equivalent power input of thermoelectric heat exchanger. Thus, the TVCC could be beneficial to the applications in small heat pumps if there is always need for auxiliary electric heat.     

影响煤层气开发效果的地质因素再认识

地质特征认识对煤层气开发效果起着重要作用。在资源特征相差不大的情况下,发现煤层气相邻井的产量差异仍较大。排除工程因素后,通过选取8类地质参数,细致比对了保德区块低产井与邻井的参数特征,筛查出其关键因素为煤层微幅构造与顶板封盖条件,其中以微幅构造为主。据此,重新认识并划分出区块新的次生褶皱背斜单元、向斜单元和斜坡单元,获得了不同次生褶皱构造单元的开发特征。结果表明,高、低产井分布与次生褶皱背斜、向斜相关性高达92%。其中:高产井主要分布在次生褶皱背斜变化较缓、呈隆起状的“平台”,且煤层顶板以泥岩、碳质泥岩为主,封盖性较好;低产井主要分布在次生褶皱向斜,同一井台各井开发效果差异表现为从向斜条带轴部—向斜条带内—向斜条带外的煤层气井平均单井产量不断增加,到向斜轴部的距离大于向斜曲率半径73.5%的范围为主力产气区,小于向斜曲率半径40.0%范围为产水主力区。这对煤层气新井部署、生产管理、开发调整等,具有一定的指导意义。     

燃气热水器在无回水管水路中实现零冷水的方案研究

本文分析了燃气热水器行业针对无回水管水路系统实现零冷水功能的现有技术方案,指出现有技术方案存在的一些缺陷,并结合试验研究,对无回水管水路系统提出了一套全新的实现零冷水功能的技术解决方案。     

抽油井不压井作业装置及抽油泵底阀设计

江苏油田的部分油井存在油管短路、地层高压低渗、漏失严重等问题,这些问题造成压井作业困难,并且压井作业过程中的井控与环境污染风险较大。为了进行不压井检泵作业,同时缩短检泵之后的产量恢复周期,进行了不压井作业技术研究,并研制了不压井作业装置。为解决起下抽油杆过程中的防喷问题,改进了抽油泵底阀结构,该结构可实现起下抽油杆过程中油管不带压、无溢流,并保障起下油管过程中的井控安全。该技术在江苏油田现场应用9井次,效果良好。     

宁夏宁东供水工程主机设备形式参数选择与国际招标

宁东供水工程供水水泵共有卧式和立式离心泵2种方案可供选择,也是工程论证时争论的焦点,经综合比较及主机设备的国际招标,最终确定了奥地利安德里兹公司的卧式双吸中开式离心泵为宁东供水工程的供水水泵。     

复合材料一体化钻井泵缸套产业化技术研究

介绍了复合材料一体化钻井泵缸套在产业化过程中的若干关键技术。通过对缸套内套材料成分和组织的优化研究,双液分时离心浇注工艺优化研究以及双液离心浇注工装开发,实现了新工艺缸套的产业化。与现行的热镶装双金属缸套工艺相比,采用新技术生产的缸套平均使用寿命超过750h,生产成本下降了20%。     

Nd:YVO4/KTP全固化倍频激光器的研究

介绍了两种腔型结构不同的Nd:YVO4/KTP全固化倍频绿光激光器,对腔结构参数进行了优化计算;在相同的实验条件下,对这两种腔的输出和稳定性等特性进行了比较和深入分析,在此基础上得出结论,提出改进措施。该折叠腔方案已进入产品化阶段。     

降低成品油二次物流运输成本的思考

介绍了传统成品油进货和管理模式存在的诸如成品油物流以行政区划、中问环节多、信息化程度不高、运输路线未优化造成物流成本提高等问题。提出要降低成品油二次物流运输成本，当务之急是加强成品油物流的信息化建设；调整管理模式，打破行政区域界限，开展经济辐射半径内的库站物流配送；引进竞争机制，打破运输垄断，一、二次物流结合，大、小车型搭配，提高运营效率；做好运杂费全面预算、核算及运行费用的过程控制。