磨料有序排布电镀砂轮的制备及其把持力研究

为解决电镀砂轮磨削加工中容屑空间不足的问题，采用点胶微粘接的方法制备了磨料有序排布的电镀砂轮，分析了磨料粘接效果和镀层力学性能。通过SEM分析了磨料/镀层/导电胶的结合界面，并进行了干磨削试验。研究结果表明，直径约为磨料粒径40%的胶点可粘接住磨料，单个胶点上粘接多颗磨料的占比小于6%；双脉冲电镀工艺制备的镀层显微硬度大于500HV，表层残余应力小于100MPa，磨料/镀层/导电胶之间的界面贴合紧密，无明显缺陷；砂轮在磨削时没有出现磨料脱落现象。     

Study on the non-uniform contact during ELID groove grinding

This paper introduces the potential feasibility that ELID (electrolytic in-process dressing) grinding replaces superfinishing in bearing manufacturing, but ELID grinding will bring new challenges. Different regions present distinguish surface profile due to the non-uniform contact in ELID groove grinding. However, few reports explaining the non-uniform contact are available. This article explores the mechanisms of the non-uniform contact during ELID groove grinding. Experiments on the non-uniform contact between bearing raceway and grinding wheel have been carried out under different conditions. The results show that non-uniform contact exists in ELID groove grinding process and it exerts influence on the profile of the raceway surface. Non-uniform contact influences the Rsk and Rku value all the time, but it influences the Ra value occasionally. Improvement strategies of eliminating the non-uniform contact are also discussed based on the experimental study.     

综放高瓦斯矿井煤层瓦斯涌出量综合预测

为了成功预测竹林山煤矿综放高瓦斯矿井大采高工作面煤层瓦斯涌出量,以主采3号煤层为主要研究对象,针对3号煤层以往开采情况,通过布设测点测量其煤层瓦斯含量和了解相邻矿井瓦斯含量,采用分源预测法、回归法及统计法等预测方法得到了3号煤层瓦斯含量的分布规律,并绘制了3号煤层的瓦斯含量等值线图。对矿井不同生产时期的瓦斯含量进行预测,得到了生产前期、中期及后期采区的最大绝对瓦斯涌出量和最大相对瓦斯涌出量,说明了竹林山煤矿各个时期均属于高瓦斯矿井。     

分层注水井智能测试调配技术试验评价

注水井智能测试调配技术在不改变原注水管柱的基础上，利用井下可调式堵塞器，通过地面电脑控制，实现了测试调配同步进行。通过7口井的现场试验及分析评价，表明该工艺具有测调精度高、测调时间短、测试资料准确等特点。     

井下液气分离器分离原理及结构改进

液气分离器就是充分利用电泵机组的高转速、气体和液体之间悬殊的密度差异进行液气离心分离。经过多年的发展,在传统的液气分离器结构基础上又出现了许多新的设计和改进,大大提高了液气分离器的分离效果。文章重点论述了液气分离器的分离原理和结构上的改进之处。     

利用反射纵波评价裂缝倾角的模拟实验研究

声波全波列测井中的反射纵波可以用来评价高角度裂缝和对井周附近地质结构进行成像。目前的研究主要侧重于直接从波形资料处理出发计算裂缝的位置和倾角 ,其可靠性和准确性无从评价和校验。文中采用模拟实验的方法记录了倾角为 6 0°～80°范围内的 8种倾角裂缝的反射脉冲纵波波形 ,自行推导了反演裂缝倾角的公式 ,结合波场分离技术对实验测量波形数据进行了处理 ,计算出的裂缝倾角与实际值具有良好的一致性。本文结果表明 ,利用至少 2个深度点的纵波反射波波形资料就可以准确地反演裂缝的倾角     

分离式热管换热器在脱硫装置的应用

介绍了分离式热管换热器的工作原理及其在工业脱硫装置中的应用，并不其余热回收情况与传统的二次中热方法相比较，阐明了其节能及环保作用。     

长距离管线监测系统的一种智能化过流防护方法

介绍了长距离管线监测系统的一种智能化过流防护方法，详细说明其电路设计原理及相关元件的选择，并与串联自复过流保护元件方式相比较，分析其整体性能，说明其具有响应速度快，安全可靠等特点。     

KZON-50/120空分设备的安装调试及设计改造

在KZON-50/120空分设备的安装调试和试运行过程中,对其机械和电器部分进行了多处改造,克服了原设计中存在的不足之处。改造后,机械和电器性能更加趋于合理,操作简单,便于维护,降低了制气费用,提高了制气纯度和经济效益,保证了空分设备更加安全可靠运行。     

Simulation of Strength Distribution in Ground Ceramics by Incorporating Residual Stress Effect

Strength of ground ceramics may be affected by residual stress as well as surface flaws induced by grinding. Strength prediction for ground ceramics is convenient for mechanical design of ceramic components. In this article, a numerical procedure based on fracture mechanics was proposed to estimate strength distribution of ground ceramics by considering grinding-induced residual stress. Bending strength and residual stress of ground ceramics were measured for three grinding-conditions. By comparison of simulated results with experimental ones, it was revealed that strength characteristics in experiments were well simulated by using the proposed procedure.