直流电动机参数测定

根据直流电机的可逆原理并利用常规的实验仪表，可以简便、准确地测出直流电动机的主要参数－电磁转矩、输出转矩和效率．     

An automatic torque ripple compensation system for direct drive motors

A serious problem in motion control is the occurrence of torque ripple. Since a direct drive (DD) motor with a magnet rotor uses a rare-earth magnet, the torque ripple is more serious than that of conventional servomotors. This paper presents an auto-compensation of torque ripple using a software-implemented torque observer. The frequency and amplitude of torque ripple can be obtained in the controller by using the estimated torque from an observer, and the autonomous generation of a compensating current component for a torque ripple is possible. The proposed algorithm has been verified by experiments.     

热流法计算高温炉内辐射传热

高温炉内的辐射传热是工业生产中常遇到的问题。过去，人们在应用热流法计算辐射传热时遇到了一定的困难，使计算结果与实际有一定的偏差。本文运用文献［１］中给出的新热流数学模型，开发出由新热流方程与能量方程相耦合的计算机程序，其中的比热流参数由线加热热源情况下计算得到。用该程序计算了实验室用马弗炉内的温度场，并且用热电偶实测了炉内的一些温度值，理论计算与实测值符合很好。     

低压铝箔交流腐蚀研究

在３０Ｈｚ频率下，通过铝箔在ＨＣｌ＋Ｈ２ＳＯ４＋ＨＮＯ３＋Ｈ３ＰＯ４体系中的交流腐蚀，研究腐蚀液组成中腐蚀主体及缓蚀剂对铝箔腐蚀的作用，探讨腐蚀过程中电源频率、腐蚀液温度、电流密度及腐蚀时间对铝箔腐蚀的影响。腐蚀液组成的配比恰当，有利于比容的提高。在特定的频率下采用合适的腐蚀液温度、适宜的电流密度和腐蚀时间可以提高铝箔的静电容量。     

基于预前控制异步电机直接转矩控制方案的研究

在传统异步电动机直接转矩控制方案中，由于负载的变化规律不可预测，因此其常会带来较大的开关频率的变化，为此提出了一种基于预前控制的异步电动机直接转矩控制的方法。该方法依据前一个周期的磁链和转矩误差，对下一个开关周期所应施加到异步电动机的定子电压矢量进行预测，然后借助空间矢量PWM的方法，合成此开关电压矢量。样机实验结果表明，该方案不但能维持逆变器的开关频率基本恒定，而且还具有比传统直接转矩控制更为优良的动静态特性。     

三相异步电动机运行指标的分析

利用电机学理论分析了影响电机起动转矩、起动电流、最大转矩和最小转矩的因素。     

Steady-state torque control system with secondary-current feedback for three-phase squirrel-cage induction motors

This paper presents a highly stable steady-state torque control system with a feedback of a secondary current signal. The torque control system is constructed with a feedback of the secondary current (I₂) signal using a quick response magnetic-field sensor constructed with an amorphous core multivibrator bridge, which can solve the secondary resistance change problem for temperature variation in the IM. Moreover, we added a state feedback to the system to improve the response speed for the unit step function of a torque order. The I₂ sensor method has advantages especially at a low-speed range, in which conventional method using an integrator shows control errors.     

In－BiCaVIG的晶体生长与性能

本文报导了用助熔剂法成功地生长大尺寸掺铟ＢｉＣａＶＩＧ晶体的方法以及实验结果，介绍了该单晶在近红外区的磁光器件中的重要应用。     

Relaxation phenomena caused by equilibration of point defects

Relaxation phenomena due to equilibration of point defects in metals are reviewed. The relaxation effect in specific heat observed in tungsten and platinum confirms that in both cases the nonlinear increase in the high-temperature specific heat has to be attributed to point-defect formation. Relaxation phenomena observed by measurements of electrical resistivity and positron annihilation are also considered. The comparison of the data seems to be favorable for the conclusion that all the phenomena are of one origin.     

Effect of doping polyacrylic acid with some dopants as studied by different techniques

The molecular weight of polyacrylic acid (PAA) was determined by a viscometric method using NaNO₃ as solvent at 30°C. The specific electric conductivities (σ) of PAA as well as PAA doped with carbon black (CB), chromium oxide (Cr₂O₃), and cupferron with different concentrations (from 0.25 to 1 wt %) were measured at a temperature range 360–400 K. IR spectra of some polymers were determined and it was shown that when PAA was doped with 0.5 wt % CB, a C? O? C band appeared at 775–875 cm^?1. The positron annihilation lifetime (PAL) spectra in PAA doped with the above‐mentioned dopants were measured as a function of their concentrations. It was observed that the short lifetime intensity I₁ decreased, whereas the intermediate lifetime intensity I₂, which is related to the conductivity of the material, increased with increasing the wt % of Cr₂O₃ and cupferron as well as at low concentrations of CB. These results are discussed in terms of the conducting island model. It was found that there were distinct positive relationships between σ and I₂. © 2002 John Wiley & Sons, Inc. J Appl Polym Sci 84: 877–883, 2002; DOI 10.1002/app.10381