Experimental research on combined effect of obstacle and local spraying water fog on hydrogen/air premixed explosion

In order to reveal the mechanism of water fog explosion suppression and research the combined effect of water fog and obstacle on hydrogen/air deflagration, multiple sets of experiments were set up. The results show that the instability of thermal diffusion under lean combustion conditions is the main influencing factor of hydrogen/air flame surface instability, and the existence of water fog will aggravate the hydrogen/air flame surface instability. When obstacle is not considered, 8 μm, 15 μm, 30 μm water fog can significantly reduce the flame velocity and explosion overpressure of hydrogen/air, 45 μm fine water fog plays the opposite role. When considering the relative position of the water fog release position and the obstacle, the 8 μm, 15 μm, 30 μm water fog has almost no suppression effect when released near the obstacle, but a significant suppression effect occur, when using the 45 μm water fog. In the field of theoretical research, the research results not only provide an experimental basis for the fine water fog to reduce the consequences of hydrogen explosion accidents, and the optimal diameter range used by the water fog, but also provide experimental reference for the numerical simulation of hydrogen/air explosion suppression in semi-open space, and promote the development of hydrogen explosion suppression theory. In terms of engineering applications, this study can provide a theoretical basis for the layout of fire fighting equipment in the engine room of nuclear power plants or hydrogen-powered ships.     

内燃机活塞环表面处理技术

活塞环在内燃机中有着支撑、密闭、储油、导热的作用,内燃机活塞环制备材料应该具备优良的加工性能、耐高温、耐腐蚀、导热性好且具有良好的强韧性,较好的与气缸材料表面的磨合性能。球墨铸铁和专用钢材已经成为制备内燃机活塞环的基础材料,目前国内外采用多种表面处理技术比如:镀铬、氮化、PVD与CVD镀膜、喷钼、喷涂陶瓷层等表面处理工艺进行表面改性,提高内燃机活塞环的使用寿命和使用性能。需要不断研究和开发新的内燃机活塞环的表面处理技术来满足实际生产和应用中内燃机越来越高的要求。     

Present status and future prospects of plasma sprayed multilayered thermal barrier coating systems

Thermal barrier coatings (TBCs) play a pivotal role in protecting the hot structures of modern turbine engines in aerospace as well as utility applications. To meet the increasing efficiency of gas turbine technology, worldwide research is focused on designing new architecture of TBCs. These TBCs are mainly fabricated by atmospheric plasma spraying (APS) as it is more economical over the electron beam physical vapor deposition (EB-PVD) technology. Notably, bi-layered, multi-layered and functionally graded TBC structures are recognized as favorable designs to obtain adequate coating performance and durability. In this regard, an attempt has been made in this article to highlight the structure, characteristics, limitations and future prospects of bi-layered, multi-layered and functionally graded TBC systems fabricated using plasma spraying and its allied techniques like suspension plasma spray (SPS), solution precursor plasma spray (SPPS) and plasma spray –physical vapor deposition (PS-PVD).     

New anti-ablation candidate for carbon/carbon composites: Preparation,composition and ablation behavior of Y2Hf2O7 coating under an oxyacetylene torch

Y₂Hf₂O₇ possesses low thermal conductivity and high melting point, which make it promising for a new anti-ablation material. For evaluating the thermal stability and the potential applications of Y₂Hf₂O₇ on anti-ablation protection of C/C composites, Y₂Hf₂O₇ ceramic powder was synthesized by solution combustion method and Y₂Hf₂O₇ coating was prepared on the surface of SiC coated C/C composites using SAPS. Results shown that the coating exhibits good ablation resistance under the heat flux of 2.4?MW/m² with the linear and mass ablation rates are 0.16?μm?s^?1 and ?0.028?mg?s^?1, respectively, after ablation for 40?s. With the prolonging of the ablation time, the increasing thermal stress causes the increase of cracks. Moreover, the chemical erosion from SiO₂ and the physical volatilization of low temperature molten products aggravate failure of the Y₂Hf₂O₇ coating.     

双排桩门架—锚杆新型组合支护体系的应用研究

本文分析了双排桩门架支护结构的受力机理。针对工程实际进行变形分析,提出增设锚杆形成锚杆———双排桩门架式组合支护体系的方法,并与监测数据对比、验证。     

一种估算单桩经济直径的方法

在滩海油田开发过程中,经常需要设立立管桩,在环境荷载的作用下,立管桩顶部会发生位移,较大的位移对立管及栈桥的安全很不利,因此需要合理确定单桩的直径。埕岛油田在确定单桩直径时引入了经济直径的概念,文章对经济直径的原理进行了分析,给出了桩顶位移和桩径经济指数计算公式,并举例进行了计算,得出了桩径与桩顶位移及桩径经济指数的关系曲线, 进而求得经济桩径的取值范围。文章还对该方法的优缺点进行了分析。     

纳米ZrO2等离子涂层的结构,性能和工艺特点

采用大气等离子喷涂技术(APS)，制备了常规氧化锆和纳米结构氧化锆两种涂层．利用扫描电镜(SEM)对涂层的显微结构进行了观察．对两种涂层的沉积效率、表面粗糙度和显微硬度作了对比研究．结果表明，粉末原料的显微结构、粒度、形态、喷涂工艺参数(喷涂功率和距离)对涂层的显微结构有较大的影响．等离子喷涂造粒纳米氧化锆粉制备的涂层沉积效率高而稳定，其显微结构与喷涂功率和距离密切相关．与常规氧化锆涂层相比，纳米结构氧化锆涂层具有较高的显微硬度和较低的表面粗糙度．     

挤扩支盘桩在湿陷性黄土地基中的应用

湿陷性黄土具有遇水发生湿陷、承载力大幅度降低的性质,这种性质直接影响到基础的承载力。为了研究支盘桩在湿陷性黄土地基中的承载性状,对湿陷性黄土中的3根支盘桩进行预浸水静载荷试验,结果表明,支盘桩荷载—沉降曲线为缓变型,具有较好的承载性能,荷载传递规律与在非湿陷性黄土地基中具有相似的性质,桩身各段承载力的发挥具有明显的顺序性,其结果为挤扩支盘桩在湿陷性黄土地基中的应用提供了依据。     

粉喷桩处理软弱地基在祁临高速公路的应用

结合工程实例，介绍了粉喷桩的所属类型，粉喷桩对软弱地基加固的原因，所适应土质及加固特点，阐述了祁临十八合同段的粉喷桩施工过程及施工中应注意的若干问题，得出粉喷桩处理不良地基效果良好。     

柔性桩沉降可靠性的简化分析公式

本文提出了结合分层的剪切位移法、摄动法和随机场理论来计算柔性桩沉降可靠度的简化方法，并用随机有限元和蒙特卡洛模拟法对此简化模型的精度进行了对比分析，分析结果表明该方法计算简便，精度较高。通过算例发现，在土的变形模量为小变异的情况下，其概率模型对桩的沉降可靠度影响不明显，因此其概率模型可近似采用正态分布；在土的变形模量为大变异的情况下，其概率模型对桩的沉降可靠度影响非常明显，在选择概率模型时要慎重。对于土的变形模量服从对数正态分布的情况，采用将其当量正态化后的中心点法即使在参数大变异的情况下也可以获得理想的计算精度。