Large domain-wall currents in epitaxial Au/BiFeO3/SrRuO3 thin-film capacitors with modulated oxygen vacancy and wall densities

Large domain wall (DW) conductivity in an insulating ferroelectric plays an important role in the future nanosensors and nonvolatile memories. However, the wall current was usually too small to drive high-speed memory circuits and other agile nanodevices requiring high output-powers. Here, a large domain-wall current of 67.8 μA in a high on/off ratio of ~4460 was observed in an epitaxial Au/BiFeO₃/SrRuO₃ thin-film capacitor with the minimized oxygen vacancy concentration. The studies from read current-write voltage hysteresis loops and piezo-response force microscope images consistently showed remaining of partially unswitched domains after application of an opposite poling voltage that increased domain wall density and wall current greatly. A theoretical model was proposed to explain the large wall current. According to this model, the domain reversal occurs with the appearance of head-to-head and tail-to-tail 180° domain walls (DWs), resulting in the formation of highly conductive wall paths. As the applied voltage increased, the domain-wall number increased to enhance the on-state current, in agreement with the measurements of current-voltage curves. This work paves a way to modulate DW currents within epitaxial Au/BiFeO₃/SrRuO₃ thin-film capacitors through the optimization of both oxygen vacancy and domain wall densities to achieve large output powers of modern domain-wall nanodevices.     

Effects of structural parameters on water film properties of transpiring wall reactor

Corrosion and salt deposition problems severely restrict the industrialization of supercritical water oxidation. Transpiring wall reactor can effectively weaken these two problems by a protective water film. In this work, methanol was selected as organic matter, and the influences of vital structural parameters on water film properties and organic matter removal were studied via numerical simulation. The results indicate that higher than 99% of methanol conversion could be obtained and hardly affected by transpiration water layer, transpiring wall porosity and inner diameter. Increasing layer and porosity reduced reactor center temperature, but inner diameter's influence was lower relatively. Water film temperature reduced but coverage rate raised as layer, porosity, and inner diameter increased. Notably, the whole reactor was in supercritical state and coverage rate was only approximately 85% in the case of one layer. Increasing reactor length affected slightly the volume of the upper supercritical zone but enlarged the subcritical zone.     

浅谈无缝钢管的壁厚偏差

通过探讨、分析无缝钢管壁厚偏差产生的原因，提出了改善钢管壁厚偏差的一些措施，并结合实际生产，得出了比较满意的结果。     

DIRECT RESONANCE OF TURBULENT BOUNDARY LAVER OVER COMPLIANT WALLS

１．　ＩＮＴＲＯＤＵＣＴＩＯＮＴｈｅｍａｉｎｇｏａｌｏｆｔｈｉｓｐａｐｅｒｉｓｔｏｅｘｐｌｏｒｅｔｈｅｐｏｓｓｉｂｉｌｉｔｙｔｏｌｅａｒｎｍｏｒｅａｂｏｕｔｔｈｅｍｅｃｈａｎｉｓｍｏｆｔｕｒｂｕｌｅｎｔｂｏｕｎｄａｒｙｌａｙｅｒｆｌｏｗｉｎｔｅｒａｃｔｉｏｎｓａｎｄｉｔｓｅｆｆｅｃｔｓｏｎｃｏｍｐｌｉａｎｔｗａｌｌｐｅｒｆｏｒｍａｎｃｅ．Ｔｈｅｒｅａｒｅｃｅｒｔａｉｎｐｒｅｒｅｑｕｉｓｉｔｅｃｏｎｄｉｔｉｏｎｓｔｏｆｕｒｔｈｅｒｔｈｅｓｔｕｄｙｏｎｔｈｅｍｅｃｈａｎｉｓｍ，ｉ．ｅ．ｔｈｅｃｏ…     

网络安全中的防火墙技术

介绍了防火墙的原理、分类及其应用     

土钉墙技术在华丰湾堤防工程边坡支护中的应用

在华丰湾堤防工程施工中 ,为防止因边坡开挖而造成附近房屋出现裂缝问题 ,经论证决定采用土钉墙技术对堤基开挖进行边坡支护 ;经实施 ,堤基开挖顺利 ,附近房屋无任何位移与沉降迹象。     

New Reaction Engineering Concepts for Selective Oxidation Reactions

In order to enhance product yields in selective oxidation reactions, numerous reaction engineering concepts are being studied worldwide. Periodic operation has been investigated for decades, yet its application is limited to a few examples, such as the butane oxidation after DuPont or reverse-flow reactors for VOC removal. The use of microchannel reactors is a younger field, but it has already yielded promising results for process optimization. Catalytic wall reactors have proved to be a helpful tool for kinetic studies. On the laboratory scale, membrane reactors have displayed favorable behavior in selective oxidation. The Na vapor-catalyzed dehydrogenation of methanol to formaldehyde is a final example of an unusual new concept for selective oxidation.     

建筑墙体表面传热系数辨识研究

对实验房间南向墙体内表面中心区域的换热过程进行实验，发现当风速在0－5．5m/s之间时，表面传热系数在8－18W（m^2.K）之间波动，而风向对墙体表面传热系数影响不大；用辅助变量法分析墙体表面传热过程，并结合实验推导出墙体表面传热系数。模型的预测结果与实测结果吻合良好。