用过滤工艺全面提高铸锭质量

探讨了过滤器孔径对6063铝合金铸锭组织和性能的影响规律。在此基础上指出,在过滤工艺恰当时,不仅可以减少铸锭中的夹杂物,而且可以有效地防止裂纹、羽毛晶等连续铸锭中的常见缺陷。     

Corrosion Control by water‐soluble extracts from leaves of economic plants

Water extracts from leaves of date palm, phoenix dactylifera, henna, Lawsonia inermis, and corn, Zea mays, were tested as corrosion inhibitors for steel, aluminum, copper and brass in acid chloride and sodium hydroxide solutions using weight loss, solution analysis and potential measurements. The inhibition action was found to critically depend on metal type and solution composition. Only, date palm and henna extracts were found highly effective in reducing corrosion rate of steel in acid chloride solutions and aluminum in sodium hydroxide solutions. The inhibition efficiency increased with increasing the concentration of the extract. The inhibition was interpreted in terms of chemisorption of some active ingredients in the leaves according to Temkin isotherm.     

铝液夹杂物检测DMIRT－Ⅲ法的试验研究

提出了一种新的铝液夹杂物快速检测方法。导出了该法的检测原理方程。分析并试验研究了影响检测重复性和分辨率的因素。试验选择了较好的检测参数，并获得了较好的检测结果。     

Production and properties of micro‐porous glas bubble zinc and aluminium composites

Micro‐porous syntactic foams were produced by means of integration of glass bubbles into aluminium and zinc matrices. Preforms of glass bubbles were pressure infiltrated with the alloys AlSi9Cu9 ans ZnAl4Cu using squeeze casting. The preforms were sintered thermically without the use of bonding agents. Using the combination of different sintering steps syntactic foams with locally different densities could be produced. The mechanical properties of the foams were tested indicating a high compression strength of the foams and a very good compression energy absorption. Furthermore, corrosion behaviour and behaviour at higher temperatures were investigated.     

Ermüdungsverhalten und Dauerfestigkeit von Graphit und Aluminium – infiltriertem Graphit

Fatigue behaviour and endurance limit of graphite and of aluminium‐infiltrated graphite Fatigue properties of polycrystalline, isotropic graphite FU2590 and of FU2590 infiltrated with AlSi7Mg (FU2590/AlSi7Mg) were investigated in reversed bending tests at 25 Hz at numbers of cycles below 10⁷ and in tension‐compression tests at 20 kHz below 10⁹ cycles. The open porosity of Graphite (10‐11 Vol.‐%) was infiltrated with the aluminium alloy using the squeeze casting infiltration method, which led to an increase of the bending strength by 50 %, increase of tensile strength by 30 % and increase of stiffness by 15 %. Fully reversed tension‐compression loading of FU2590 delivers a mean endurance limit at 10⁹ cycles at the normalized maximum stresses (i.e. maximum tension stress of a cycle divided by the static strength) of 0,65±0,03. Mean numbers of cycles to failure of 10⁴ were found in fully reversed bending tests at the normalized maximum stress of 0,78. The infiltrated material shows approximately 30 % higher cyclic strength in reversed bending tests, and the mean endurance limit under tension compression loading increases by 15 %. The increased endurance limit of the infiltrated material is caused by the increased stiffness. The increased toughness of graphite due to the infiltration with aluminium is of additional beneficial influence at the higher cyclic stresses investigated in reversed bending tests and in static tests.     

铝电解电容器用橡皮塞中铁的测定

主要研究了用硫氰酸钾作显色剂，用分光光度法测定橡皮塞中铁含量的方法。并对国产和进口橡皮塞做了比较，为铝电解电容器质量水平的提高提供一条新思路。     

AN EXPERIMENTAL INVESTIGATION OF THE GROWTH OF SMALL CORNER FATIGUE CRACKS IN ALUMINIUM 6061-T651

Results of an experimental investigation of the fatigue growth of small corner cracks emanating from small flaws are presented. Growth-arrest behaviour was observed, and increases in crack length during growth periods were of the order of the transverse grain size. For the test material, the corner crack front intersects, on average, only three–six grains in the small crack regime monitored, so only a small number of constrained, interior grains is encountered. It is suggested that the presence of partially constrained surface grains may contribute to the 'anomalous' growth behaviour which has been observed by a number of investigators.
The crack growth histories of the test data presented exhibit considerable scatter. It is shown that a Student's t -test can be used to estimate confidence intervals in order to provide a measure of the observed scatter. The variation in confidence intervals in the transition from small to long fatigue crack growth is discussed.     

Simulation of Fe-Al compounds developed during single superphosphate manufacture

In order to analyse iron phosphate complexes and gel-like phases encountered in the single superphosphate process, experiments were performed with a free-Al, Fe apatite crystal of Durango from Mexico phosphate rock and sulfuric acid. Reaction products were studied by X-ray diffraction and surface analysis methods namely X-ray photoelectron spectroscopy and scanning electron microscopy. Results show that in a free Al, Fe-system, part of the Ca(H₂PO₄ )₂.H₂O (MCPM) forms before precipitation of any CaSO₄(CS) and gel-like phase such H₂SO₄.yH₃PO₄.xH₂O is formed. When iron is added, the precipitation rate of (CS) and (MCPM) increases and Fe₃(H₃O)H₈(PO₄)₆.6H₂O is formed. When Fe and Al are added, a gel-like phase is quickly formed with a molar ratio that changes with time and develops into crystalline compounds. The composition of this gel may be represented as a mixture of two phases: H₂SO₄.yH₃PO₄.xH₂O and a gel containing Al-Fe-Si.     

Impregnation of X Zeolite with Alkaline Hydroxide During the Synthesis

Enhancement of the basic properties of the X zeolite with FAU framework has been carried out during synthesis, without further treatment such as ion-exchange or impregnation. Control of the washing stage enables retention of the optimum amount of alkaline hydroxides, which increases the basic catalytic activity of X zeolite in the alkylation of toluene. This alkaline hydroxides neither affect the FAU framework nor the silicon/aluminium molar ratio of the X zeolite. The optimum (Na + K)/Al molar ratio of the improved catalyst was 1.06 corresponding to a washing volume of 200 mL. This X zeolite presented better catalytic activity than a cesium-zeolite prepared by ion-exchange. The presence of hydroxysodalite impurity in the X zeolite increased the amount of impregnated alkaline hydroxides but not the catalytic activity. The present study shows that it is possible to increase the basic properties of the X zeolite directly in the synthesis process.