基于神经网络算法的井下裂缝诊断与堵漏技术

在钻井过程中，常常钻遇不同宽度的井下地层裂缝。钻遇裂缝时容易发生钻井液漏失现象，甚至发生钻井液失返现象，严重影响了安全、高效钻井。目前裂缝封堵的方法常存在封堵成功率不高、堵漏承压能力低的问题，其中一个重要的原因是对井下地层的裂缝宽度等特征认识不清。基于地层裂缝产生的岩石力学机理，确定影响裂缝宽度关键的6个力学和工程因素，并利用神经网络计算的非线性、大数据特点建立了井下地层裂缝宽度的分析模型，模型包含输入层、输出层和3个隐藏层。通过该模型诊断井下裂缝宽度，提高了计算精度，平均误差仅为2.09%，最大误差为5.88%，解决钻井现场仅凭经验判断裂缝误差较大和依靠成像测井成本较高的问题。同时根据神经网络模型诊断得到的裂缝宽度优化堵漏材料的粒径配比，提高了裂缝内的架桥封堵强度和架桥的稳定性，封堵层的承压能力达到12.8 MPa，反向承压能力达到4.5 MPa。现场堵漏试验最高憋压10 MPa，经过封堵作业后大排量循环不漏，达到了裂缝性地层高效堵漏的目的，堵漏一次成功。      

Application of differential evolution for cascaded multilevel VSI with harmonics elimination PWM switching

Harmonic elimination pulse width modulation (HEPWM) method has been widely applied to multilevel voltage source inverter (MVSI) to remove low frequency harmonics from its output voltage. However, the computation of the HEPWM switching angles for MVSI is very challenging due to several constraints, namely angle sequencing, very tight angular spacing and the numerous possibilities of angles distribution ratio. Realizing the potential of Differential Evolution (DE) to handle complex problems, this work proposes its application to solve the HEPWM problem for cascaded MVSI. Its emphasis is on improving the availability of HEPWM for higher output voltage by extending the maximum range of modulation index (M). It also removes the discontinuities in the switching angles and reduces the number of distribution ratio required to obtain the required solution. Compared to the most advanced (similar) work, i.e., 7-level MVSI with seventeen switching angles, DE covers a wider range of M; the maximum achievable M is 2.80. Furthermore, it exhibits very low second order distortion factor (DF₂): for the worst case, the value of DF₂ is 0.0014%. To verify the viability of the proposed algorithm, simulation is carried out and hardware prototype is constructed. Both results show very good agreement with the theoretical prediction.     

M1080B无心外圆磨床改进

M1080B无心外圆磨床砂轮及导轮宽度较窄,磨削轴承套圈外圆时,磨削效率低,托板架调整较为繁琐、皮带打滑、磨损较为严重。针对上述问题,提出了相应的解决办法,提高了磨削效率。     

可调偏迈步式胶带自移机尾的研究

随着掘进工作面自动化程度的提高,掘进巷道速度也在日益加快,而现有的顺槽皮带机机尾移动缓慢且移动时工作量大,需要两三人配合操作,存在一定的安全隐患。针对以上问题,研发可调偏迈步式胶带自移机尾,具有与悬挂二运皮带转载机搭接行程长,可以迈步式前进,自动调偏等功能,同时,可以降低工人的劳动强度,加快巷道掘进速度。     

AT89C2051芯片在车载产品中的应用

本文论述了采用单片机技术研制成功的泊车用超声波测距仪的基本原理,用AT89C2051作为控制器的实现方案,以及采用软件校正的方法,提高了测量精度和整机的可靠性.     

皮带秤秤架的响应特性曲线分析

介绍了皮带秤秤架响应特性曲线分析方法，对四种结构形式的秤架进行了响应特性曲线分析和比较，得出的结论是：悬浮式秤架的计量特性最好。     

Methods of Verifying Continuous Automatic Belt Weighers: State and Prospects

The basic methods of verifying continuous automatic belt weighers are described. A comparative analysis of these methods on the basis of experimental studies is made and ways of implementing the results in industry are recommended.     

浅谈延迟焦化装置露天栈桥的设计

根据延迟焦化装置露天栈桥的工程设计实践,围绕一炉两塔(一个加热炉两个焦炭塔)的焦化装置,分析了露天栈桥设计中的要点及难点,对其在平面布置、基础安排和吊车梁选型等设计方面做一些介绍和论述。     

正当防卫--运用反倾销协议维护自身权益

介绍了中国首次反倾销案的胜诉，阐述了如何正确认识倾销和如何运用反倾销。     

混凝土小型砌块建筑裂缝宽度的标准设置研究

通过对混凝土小型空心砌块单片墙进行试验 ,了解不同构造措施墙体的初始裂缝在墙体上出现的部位、形态、发展规律以及墙体最终破坏形态 ,并通过试验明确墙体在不同受力状态下的裂缝形态 ,最后根据试验结果初步提出混凝土小型空心砌块建筑的裂缝宽度控制标准