鹤岗煤田新华勘探区主要煤层对比浅析

介绍了鹤岗煤田的地质概况 ,并对主要可采煤层的一些比较明显的特征进行了对比。     

松软厚煤层轻放工作面切眼锚杆支护实践

针对朱仙庄矿 84 15工作面切眼特殊的地质条件 ,介绍了高强锚杆 (索 )支护技术成功应用于特厚极软煤层的经验 ,并对巷道支护成本进行了分析     

省煤器管开裂原因分析

对省煤器开裂管进行了化学成分及宏、微观分析。分析结果表明，在高温高压条件下，在其焊缝溶合区出现粗大的魏氏组织，管材中的珠光体组织产生了不同程度的球化，而母材组织又存在严重的带状组织。在过热条件下熔合区极易出现裂纹，并由此快速扩展，造成省煤器管开裂。     

亚硝酸钠作释放剂选择性螯合滴定法测定钯

用EDTA螯合Pd^2 和其它金属离子，然后用亚硝酸钠分解Pd—EDTA螯合物，释放出的ED—TA用Zn^2 标准溶液进行返滴定。大量各种金属离子都不干扰。用于测定Pd—Cu合金镀层、Pd—Sn—Cu合金镀层和Pd—Ti—Si合金中的钯，获得相当满意的结果。     

国内外厚煤层大功率电牵引采煤机机电一体化新技术

介绍国内外大功率厚煤层电牵引采煤机的机电一体化新技术,包括总体技术、交流变频电牵引技术、工况检测、故障诊断技术、自动调高技术、远程通讯和集中控制技术。     

近距离下覆4#煤层综采工作面顶板管理经验

介绍了近距离深层综采工作面顶板和巷道顶板管理经验，及综采工作面在通过巷道冒项区域时所采取的办法和措施。     

液化气球罐焊缝H2S应力腐蚀裂纹的返修补焊

对宁夏炼油厂一台200m3低合金钢球罐H2S应力腐蚀裂纹采用气刨打磨后补焊的返修方法表明，碳弧气刨时的骤热不会使裂纹向纵深扩展，只是必须在补焊前将返修部位焊缝两侧各100mm范围内打磨至完全露出金属光泽，以便彻底消除裂纹源，避免补焊时再产生新的微小裂纹。若返修深度不大于罐壁厚度的二分之一，则不必进行射线探伤检查，只须进行100％的超声波检查，在水压试验前后对返修部位进行100％磁粉探伤则是非常必要的。     

铝合金激光-电弧复合焊接工艺研究

对LF6铝合金的激光-电弧复合焊接工艺进行了初步研究。通过工艺试验,分析研究了焊接速度、激光焦点位置、钨极与激光束之间的距离、焊接电流对焊缝质量(熔深、熔宽)的影响规律。     

Similarity model tests of movement and deformation of coal-rock mass below stopes

For a study of the movement and deformation of coal-rock mass and low protected seams below a stope,as well as for fracture developments and rules of evolution of permeability,we designed a plane strain model test stand to carry out model tests of similar materials in order to improve the effect of gas drainage from low protected seams and to measure the movement and deformation of coal-rock mass using a method of non-contact close-range photogrammetry.Our results show that 1) using paraffin melting to take the place of coal seam mining can satisfy the mining conditions of a protective seam;2) coal-rock mass under goafs has an upward movement after the protective seam has been mined,causing floor heaving;3) low protected seams become swollen and deformed,providing a good pressure-relief effect and causing the coal-rock mass under both sides of coal pillars to become deformed by compression and 4) the evolution of permeability of low protected seams follows the way of initial values→a slight decrease→a great increase→stability→final decrease.Simultaneously,the coefficient of air permeability increased at a decreasing rate with an increase in interlayer spacing.     

An evaluation of deep thin coal seams and water-beating/resisting layers in the quaternary system using seismic inversion

Non-liner wave equation inversion, wavelet analysis and artificial neural networks were used to obtain stratum parame-ters and the distribution of thin coal seams. The lithology of the water-bearing/resisting layer in the Quaternary system was also predicted. The implementation process included calculating the well log parameters, stratum contrasting the seismic data and the well logs, and extracting, studying and predicting seismic attributes. Seismic inversion parameters, including the layer velocity and wave impedance, were calculated and effectively used for prediction and analysis. Prior knowledge and seismic interpretation were used to remedy a dearth of seismic data during the inversion procedure. This enhanced the stability of the inversion method. Non-linear seismic inversion and artificial neural networks were used to interpret coal seismic lithology and to study the wa-ter-bearing/resisting layer in the Quaternary system. Interpretation of the 1-2 m thin coal seams, and also of the wa-ter-bearing/resisting layer in the Quaternary system, is provided. The upper mining limit can be lifted from 60 m to 45 m. The pre-dictions show that this method can provide reliable data useful for thin coal seam exploitation and for lifting the upper mining limit, which is one of the principles of green mining.