多业务移动通信系统中的呼叫接入控制

在多业务无线移动通信系统的呼叫接入控制中,不仅要考虑业务之间的优先级,同时也必须考虑切换呼叫的优先级。本文结合可移动边界算法和保护信道策略,提出了一种有效的多业务呼叫接入控制算法。为了方便地分析方案的性能,设计了一个二维的Markov链对方案的性能进行理论上的分析。通过数值分析结果表明,提出的算法同时保证了两种优先级,并提高了系统的性能。1     

无线电车载监测站的信号采集与通讯系统

本系统采用LabVIEW对无线电监测信号进行采集和处理．并开发用户界面。在Delphi平台上运用远程访问服务实现了无线电车载监测站与中心固定站的通讯。LabVIEW主程序对通讯子程序进行调用。     

Augmentation of boiling heat transfer from horizontal cylinder to liquid by movable particles

This paper presents a series of experimental results on a passive augmentation technique of boiling heat transfer by supplying solid particles in liquid. A cylindrical heater 0.88 mm in diameter is placed in saturated water, in which a lot of mobile particles exist, and the nucleate and film boiling heat transfer characteristics are measured. Particle materials used were alumina, glass, and porous alumina, and the diameter ranged from 0.3 mm to 2.5 mm. Particles are fluidized by the occurrence of boiling without any additive power, and the heat transfer is augmented. The maximum augmentation ratio obtained in this experiment reaches about ten times the heat transfer coefficient obtained in liquid alone. The augmentation ratio is mainly affected by the particle material, diameter, and the height of the particle bed set at no boiling condition. The augmentation mechanism is discussed on the basis of the experimental results. © 2001 Scripta Technica, Heat Trans Asian Res, 31(1): 28–41, 2002     

GPS(NR102K)常见故障与解决方法

GPS硬件由主机和副机两部分组成，本文以Sercel公司生产的NR102K型GPS全球定位系统为例，介绍了其主机和副机在野外施工中的常见故障和解决方法，具有一定的实用性。     

Numerical simulation of typical contact situations of brake friction materials

In the paper, a model typical for contact situations of automotive brakes is established based on the method of movable cellular automata. The processes taking place at local contacts in an automotive brake system are analysed. Based on microscopic and micro-analytical observations, the following contact situations were simulated: (i) a couple of ferritic steel against pearlitic steel, both covered by an oxide layer mixed with graphite nanoparticles and (ii) the same situation but without oxide layers. The results of calculated mean coefficients of friction of the oxide-on-oxide contact correspond well to expected values for a real braking system, whereas steel-on-steel contact are twice as high. This allows one to make some conclusions; for example, oxide formation will take place more quickly than friction layer elimination, and finally this is responsible for the stabilisation of the coefficient of friction.     

VGCR211型调速器在小浪底水电厂的应用

VGCR211型调速器的可编程控制器采用数字化双套冗余配置方式；应用程序由RS232串口写入用户存储器，确保电源消失后程序不会造成任何丢失；输出放大VCAl卡可独立实现对调速器的开度控制功能；转速检测单元采用齿盘测速方式，网频测量取自机端PT；导叶反馈采用角度传感器电气反馈方式。调速器的转速、开度和负荷三种控制模式可任意无扰动切换。在功能实现上，导叶采用关断阀，该阀集开停机阀和紧急停机阀功能于一体，不装事故配压阀。该调速器在小浪底水电厂投运以来其调节性能、可靠性基本达到设计要求，维护工作量较以往传统产品大大减少。     

不锈钢水泵底架成形工艺及模具设计

分析了水泵底架原冲压成形工艺存在的问题,提出了新的成形工艺方案,介绍了新工艺中关键工序的模具结构以及模具加工、现场调试应注意的事项。经生产验证,改进后的工艺与模具结构合理,产品质量及生产效率大大提高。     

圆管弯曲模活动凹模的设计

按质点的转动性质精确绘制出圆管弯曲模活动凹模模块 ,便于数控线切割机一次完成凹模加工 ,缩短了制模周期     

气动螺丝刀传动活块加工工艺分析与加工工艺

通过对气动螺丝刀传动活块加工工艺进行分析,提出了该零件的加工工艺,在普通立式铣床上加工出合格的零件,解决了进口气动工具无配件的问题。     

地面雷达可移动式天线罩的设计分析

本文讨论了地面大型雷达的可移动式天线罩的设计，针对各种设计要求比较和优选了相应的设计方案，使产品的研制获得成功。