DFIT测试在长庆气田开发中的应用

与常规的小型测试压裂不同，流体注入诊断测试（DFIT）是通过关井阶段出现的拟线性流或拟径向流阶段求取储层压力，采用改进的梅耶霍夫方法（M-method）解释储层渗透率。以长庆榆林气田一口开发井为例，依据DFIT的技术原理和测试步骤，对该井测试压降数据进行解释分析，结果可信度较高，证明了该项工艺在长庆低压低渗油气田的可行性。     

径向水平井弯曲转向机构影响因素仿真研究

针对径向水平井钻进中钻杆弯曲转向前进运动困难的问题,通过建立弯曲转向机构仿真有限元模型,对其主要影响因素:滑道轨迹曲率、间隙、工作压力、滚轮形状与位置和钻杆壁厚等用ANSYS软件进行仿真研究。研究表明:影响截面变形的主要因素是滑道曲率的改变和滑道摩擦因数,钻井失败时钻杆所受阻力的增大不是因为升高工作压力导致截面变形过大与滑道干涉所致,钻杆经校直段,钻头中轴线与校直中心线存在一定的角度,即钻杆的前进轨迹就会偏离理论值,或与地层干涉,或可能再次发生弯曲变形;另一主要原因是转向器滑道工作恶化。增加钻杆壁厚,降低工作压力和滑道摩擦因数,设计合理弯曲转向机构是解决问题的关键。     

Progressive damage modelling of SMC composite materials

The present work deals with the modelling of damage behaviour for sheet moulding compound (SMC) composite materials using a finite element analysis package. Specifically, a comparison is made between the results obtained experimentally for a three-point bending test, and those obtained from numerical simulation using a material model already implemented. The simulation has been performed for the material models available within the PAM-CRASH software. The simulation results are compared and validated with respect to experimentation.     

高抗挤厚壁套管的性能及应用效果评价

中原油田套管损坏的主要原因是现有套管强度不够,无法抵抗盐膏层段的巨大外挤力。开发了TP130TT型高抗挤厚壁套管,其强度能很好地抵抗盐膏层巨大外挤力。实验室试验表明,各项性能指标达到了设计要求,现场使用取得了很好的效果,解决了中原油田盐膏层段套管强度不足的难题。     

掺气减蚀保护作用的新概念

利用针式掺气流速仪测量原型和模型掺气浓度场、流速场，气泡尺寸及其概率分布的研究成果表明，原型水流韦伯数高，形成微小气泡的能力比模型强，气泡上浮慢，接近底部的小尺寸气泡概率及掺气浓度比模型大。初步研究认为：0.2mm或0.5mm以下的微小气泡在掺气减蚀中起着主要作用，可能只要很小掺气浓度即可达到掺气减蚀的效果。因此以小尺寸气泡的掺气浓度，作为判断掺气减蚀保护作用的指标将更为准确。     

低密度微泡沫压井液的研究与应用

吐哈油田部分区块地层压力系数小于0.9,常规水基压井液对储层伤害大,若使用油基压井液成本高,环境污染严重。通过实验优选出了一种低密度水基微泡沫压井液。该压井液具有密度低、泡沫强度高、稳定性好、携砂能力强等优点。现场应用表明,低密度微泡沫压井液稳定时间大于48 h,密度在0.70~0.99 g/cm3之间可调,抗油污染能力强,抗油大于8%,抗温在100℃以上,岩心污染后渗透率恢复值大于80%;并且施工方便,成本低,具有储层保护能力,使用微泡沫压井液的井表皮系数在0.20~2.34之间。     

A new monitoring system for piping systems in fossil fired power plants

A CEC-funded project has been performed to tackle the problem of producing an advanced Life Monitoring System (LMS) which would calculate the creep and fatigue damage experienced by high temperature pipework components. Four areas were identified where existing Life Monitoring System technology could be improved:

1. 1. the inclusion of creep relaxation

2. 2. the inclusion of external loads on components

3. 3. a more accurate method of calculating thermal stresses due to temperature transients

4. 4. the inclusion of high cycle fatigue terms.

The creep relaxation problem was solved using stress reduction factors in an analytical in-elastic stress calculation. The stress reduction factors were produced for a number of common geometries and materials by means of non-linear finite element analysis. External loads were catered for by producing influence coefficients from in-elastic analysis of the particular piping system and using them to calculate bending moments at critical positions on the pipework from load and displacement measurements made at the convenient points at the pipework. The thermal stress problem was solved by producing a completely new solution based on Green's Function and Fast Fourier transforms. This allowed the thermal stress in a complex component to be calculated from simple non-intrusive thermocouple measurements made on the outside of the component. The high-cycle fatigue problem was dealt with precalculating the fatigue damage associated with standard transients and adding this damage to cumulative total when a transient occurred.

The site testing provided good practical experience and showed up problems which would not otherwise have been detected.     

水力喷射径向水平井生产管的工艺评定与检验

在URRS系统施工过程中 ,生产管处于多种变化复杂的应力和变形状态下 ,若出现失稳、渗漏、刺穿和断裂等事故 ,将造成巨大经济损失。为此 ,开展了水力喷射径向水平井用生产管的焊接方法、焊接设备、焊接工艺过程和焊接接头力学性能评定方法的试验研究。通过研究和试验 ,管材基本上实现了国产化 ,与之相匹配的焊接材料、焊接工艺以及质量检测技术已基本配套和规范化 ,形成了一套稳定的、可靠性较高且能完全满足现场工况的施工体系和质量保证体系     

新疆伊犁托海水电站拱坝坝体变形监测分析

根据托海拱坝5号坝段、7号坝段例垂线实测资料分析，说明了新疆寒冷地区坝体采取聚胺脂喷涂施工措施后对坝体变形的影响，以及右坝肩渗漏对右坝肩岩体的影响，分析结果为托海水电站通过国家电力公司大坝安全监察中心大坝安全首次定检提供了科学依据。     

Suggestions for the quantitative X-ray microanalysis of thin sections of frozen-dried and embedded biological tissues

When a microregion in a thin section of frozen-dried and embedded tissue is analysed by the conventional electron-probe X-ray continuum-normalization method, the measured quantity is in mmol of element per kg of embedded specimen. As each microregion contains an unknown amount of embedding medium, this quantity generally lies indeterminately somewhere within the wide range between mmol of element per kg of hydrated tissue and mmol of element per kg of dehydrated tissue. However, if a ‘tag’ element is incorporated in the embedding medium, the contribution of the medium to the local continuum count in each probed field should be measurable, and the X-ray data may then unambiguously yield mmol of element per kg of dehydrated tissue. This result should not be affected by shrinkage on freeze-drying or by incomplete replacement of water by embedding medium. The same X-ray data can additionally provide estimates of mmol of element per unit volume, mmol of element per kg of hydrated tissue and local dry-mass fraction. However, these estimates are subject to errors due to tissue shrinkage, incomplete replacement of water and beam damage.