基于滚动摩擦作用下玉米颗粒在模拟筒仓卸料中的力链分析（网络首发、推荐阅读）

针对颗粒滚动摩擦作用对筒仓中玉米颗粒的力链空间分布进行研究，通过EDEM离散元软件建立筒仓模型与仿真玉米颗粒模型进行卸粮仿真模拟，并与筒仓卸料实验作流态对比，验证模型与仿真结果的准确性。通过对模拟仓进行切片观察和数据处理，对比分析了不同摩擦情况下力链的细观参数随时间演化规律。模拟结果表明：颗粒间摩擦系数越大，卸粮完成的最终时间越长；颗粒间滚动摩擦系数越小，颗粒由整体流转变为管状流的时间越早。对于有漏斗的筒仓来说，减小颗粒间摩擦会改变整体流和管状流之间的极限，从而增加产生管状流的面积。标准滚动摩擦系数下玉米颗粒在卸料过程中会出现起拱-塌陷效应；减小滚动摩擦，玉米颗粒卸料较稳定，未出现起拱的应力突增、以及拱塌陷的应力衰减；增大颗粒间滚动摩擦不但会增加拱效应，且出现成拱高度距离漏斗口更高。     

Effect of spheroidized microstructure on the impact toughness and electrochemical performance of a high-carbon steel

The influence of cementite spheroidization on the impact toughness and electrochemical properties of a high-carbon steel has been thoroughly investigated in this study. Heavy warm rolling, followed by 2 h of annealing, has resulted in near-complete spheroidization, leading to a microstructure consisting of nano-cementite globules dispersed in the ultrafine-grained ferritic matrix. The Charpy impact test exhibited superior impact toughness with increased spheroidization. It is validated by the presence of abundant dimples in the fractographs of spheroidized specimens, in contrast to the as-received one that experienced a brittle failure due to its lamellar pearlitic structure. Potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) carried out in a 3.5% NaCl solution revealed that the corrosion resistance of the alloy gets improved with the increase in the degree of spheroidization. This is attributed to the lower susceptibility of the spheroidized specimen to microgalvanic corrosion owing to the minimum area of contact between nano-spheroidized cementite and ferrite, as elucidated with the help of EIS results aided by equivalent electrical circuit model.     

Rectangular Section Control Technology for Silicon Steel Rolling

Rectangular section control technology(RSCT)was introduced to achieve high-precision profile control during silicon steel rolling.The RSCT principle and method were designed,and the whole RSCT control strategy was developed.Specifically,RSCT included roll contour design,rolling technology optimization,and control strategy development,aiming at both hot strip mills(HSMs)and cold strip mills(CSMs).Firstly,through the high-performance variable crown(HVC)work roll optimization design in the upper-stream stands and the limited shifting technology for schedule-free rolling in the downstream stands of HSMs,a hot strip with a stable crown and limited wedge,local spot,and single wave was obtained,which was suitable for cold rolling.Secondly,an approximately rectangular section was obtained by edge varying contact(EVC)work roll contour design,edge-drop setting control,and closed loop control in the upper-stream stands of CSMs.Moreover,complex-mode flatness control was realized by coordinating multiple shape-control methods in the downstream stands of CSMs.In addition,the RSCT approach was applied in several silicon-steel production plants,where an outstanding performance and remarkable economic benefits were observed.     

冷轧平整机机前甩尾轧制工艺的开发与应用

本文介绍了柳钢冷轧板带厂1550 mm单机架平整机机前甩尾轧制的工艺。改进前轧制每卷钢卷生产效率低,钢卷成材率低,改进后生产效率、成材率明显提高,部分规格的钢卷能实现带尾剪切长度为零。     

积分中值屈服准则解析厚板轧制椭圆速度场

为解决非线性Mises比塑性功率积分困难以及由此导致的轧制功率解析式难以获得的问题,本文通过建立并利用线性比塑性功率表达式对提出的椭圆速度场进行能量分析,得到了轧制力能参数的解析解.文中通过对变角度屈服函数求积分中值,构建了一个新的屈服准则,它是主应力分量的线性组合,在π平面上的轨迹是逼近Mises圆的等边非等角的十二边形,其基于Lode参数表达式的理论结果也与实验数据吻合较好.同时,根据厚板轧制时金属流动速度从入口到出口逐渐增大的特点,提出了水平速度分量满足椭圆方程的速度场,该速度场满足运动许可条件.通过相应的轧制能量分析,获得了基于线性屈服准则的内部变形功率以及基于应变矢量内积法上的摩擦功率与剪切功率.在此之上,通过泛函的极值变分导出了轧制力矩、轧制力以及应力状态系数的解析解,并与现场实测数据进行了对比,结果表明利用本文提出的屈服准则与速度场所建立的轧制力矩与轧制力模型与实测值吻合较好,其中轧制力误差小于5.3%,轧制力矩误差在6%左右.     

On the thermally-induced seizure in bearings: A review

This paper presents a state-of-the-art survey of papers reported on the nature of a troublesome failure mode in bearings known as seizure. This mode of failure is thermally-induced and it occurs in both journal and rolling element bearings. To gain insight, particular attention is given to reported experimental observation, various mechanisms involved, and available prediction methodologies.     

轧制始极片

本文介绍了轧制法生产始极片的工艺，比较了轧制法和传统的钛种板生产始极片的优缺点，讨论了采用轧制始极片的经济效益和应用前景。     

横泉水库大坝土料碾压试验

在取得土料场土料物理力学性质参数的情况下，遵循碾压试验基本原理、方法及参数组合，进行了现场碾压试验，通过试验成果的分析，得出了大坝碾压试验结论，为大坝土方填筑提供了技术依据。     

滚动式冷床在高钢级油管生产线中的应用

根据石油开采业对石油机械产品的需求 ,利用机械理论基础知识 ,通过实践设计 ,提出了对几何尺寸长的金属管类进行调质处理后的均匀冷却方法 ,以满足其性能要求。