Annular‐ring slot antenna designs with circular polarization radiation

The design of a microstrip‐fed annular‐ring slot antenna (ARSA) with circular polarization (CP) radiation is initially studied. To obtain CP radiation with broad 3‐dB axial ratio (AR) bandwidth that can cover the WiMAX 2.3 GHz (2305–2320 MHz, 2345–2360 MHz) and WLAN 2.4 GHz (2400–2480 MHz) bands, a novel technique of extending an inverted L‐shaped slot from the bottom section of the annular‐ring is proposed. To suppress the harmonic modes induced by the CP ARSA, the technique of integrating a defected ground structure into the annular‐ring slot is further introduced. From the measured results, 10‐dB impedance bandwidth and 3‐dB AR bandwidth of 44.86 and 9.68% were achieved by the proposed harmonic suppressed CP ARSA. Furthermore, average gain and radiation efficiency of ～4.7 dBic and 71%, respectively, were also exhibited across the bands of interest. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:337–345, 2015.     

简体接管边缘应力区局部减薄处应力特征

参考《压力容器定期检验规则》第40条,采用有限元方法计算了筒体接管边缘应力区局部减薄处的应力分布,得到了局部减薄处凹坑的尺寸与位置对应力的影响趋势,讨论了应力集中系数随尺寸变化的规律,为筒体接管边缘应力区局部减薄处的强度评定提供了一定的计算依据。     

LARGE EDDY SIMULATION OF VERTICAL JET IMPINGEMENT WITH A FREE SURFACE

1. INTRODUCTION When wastewater is discharged into rivers, lakes or oceans, it usually leads to the formulation of turbulent jet with a free surface. If the ambient water depth is shallow, the jet will impinge on the water surface and the confinement of f…     

螺旋槽管强化传热原理及在石化装置上的应用前景

详细介绍了螺旋槽管换热器的强化传热原理 ,阐明了在无相变和有相变两种工况下 ,螺旋槽管换热器的强化作用 ,并介绍了螺旋槽管换热器的设计计算方法。说明了在石油化工装置上应用的必要性     

小型中间下料预焙电解槽技术条件摆布的思考

对小型中间下料预焙电解槽技术条件摆布的原则和具体数据进行了探讨，提出了尽可能利用从大型预焙槽上得出的先进经验，并消化吸收，掌握好各种条件的平衡，以取得好经济技术指标的观点。     

斜槽电机铁心叠压胎的设计

文章介绍了一种电机铁心为斜槽的叠压胎,重点分析了叠压胎定位 斜键的设计及其公差计算。     

带纵向槽筒形件拉深方法的研究

针对传境拉深带纵向槽筒形件的方法的缺点,采用一次拉深成形的方法,并通过试验和计算获得毛坯的形状和尺寸。     

小孔矩形腔体屏蔽特性的研究

本文提出了有孔腔体远、近场电磁屏蔽效能的计算方法，体研究了矩形腔体的屏蔽特性，讨论了各类孔对屏蔽能的影响程度。数值结果表明，理论计算与实验数据吻合较好。     

液压卡紧的原因及其消除措施

针对液压系统中经常出现的液压卡紧现象，初步分析了其原因及消除措施。     

重视工序细部做法 确保后浇带施工质量

介绍后浇带施工主要的工序细部做法和施工缝处的处理方法