深部松软煤层钻孔孔周煤体变形产渣特征研究

针对煤矿井下高瓦斯软煤顺层长钻孔排渣困难、成孔率低、施工困难等问题,通过数值模拟实验研究了井下深部软煤体变形破坏特征,分析了顺层长钻孔孔周松软煤体变形特征及应力变化,以揭示顺层长钻孔孔周松软煤体变形产渣规律。研究表明:深部高瓦斯软煤顺层钻孔孔周煤体的应力平衡临界条件破坏后将发生大体积突然垮落;钻孔水平最大变形位移为1.22mm,垂直方向最大变形位移为10.7mm;径向孔周煤体垂向变形呈现逐渐减小趋势,且垂向变形明显大于钻孔水平变形。在水平方向上,钻孔孔周煤体应力分布呈现先增大再逐渐减小的变化规律,径向距离对水平应力分布的影响逐渐减小;随着径向距离的增加,钻孔孔周煤体应力分布逐渐降低,钻孔孔壁处煤体的应力出现最大值,且垂直方向处应力值最大。     

Study on the relationship between the particle size distribution and the effectiveness of the K‐powder fire extinguishing agent

The relationship between the particle size distribution and the extinguishing effectiveness of the new K‐powder fire extinguishing agent has been studied experimentally, to explore the reason of the great extinguishing efficiency exhibited by the new K‐powder fire extinguishing agent on Class B fire (liquid fuel fire). The results of the experiment showed that the extinguishing effectiveness increased along with the decrease of the particle size distribution. In addition, a sharp discontinuity appeared around the limiting size, about 40 μm. The powder with the particle size below 40 μm exhibited highly effective extinguishing with the minimum effective extinguishing concentration C_xr = 23 g·m^?3, while the powder with the particle size above 40 μm exhibited little fire extinguishing efficiency. Compared with other fire extinguishing agents produced by different substances, the new K‐powder fire extinguishing has the bigger limiting size. That means, in the same particle size distribution, the new K‐powder fire extinguishing agent contains more highly effective powder than others contain, and is more effective.     

大直径平底负压容器优化设计

通过对大直径平底负压容器平底板的设计计算,平底板计算厚度很厚。通过分析,提出了对平底板采取加强措施,从而减薄平底板计算厚度的方法。该容器在实际生产过程中性能可靠、稳定,对类似设备设计具有借鉴意义。     

Reducing treatment zone diameter in orthokeratology and its effect on peripheral ocular refraction

PurposeTo determine whether orthokeratology (OK) induced treatment zone (TZ) diameter can be reduced by altering OK lens design, and if so the impact of modifying TZ diameter on relative peripheral refraction (RPR).Methods16 subjects (mean age 23.4 ± 1.5 years; 8 female) completed the study. Standard (Control) OK lens design (PJ, Capricornia, Australia) or a modified version (Test) where the back optic zone diameter was reduced, and back optic zone asphericity and intermediate lens curves were altered, were worn overnight only for 7-nights in a randomised double masked order, with a minimum 1-week wash out (no lens wear) between lens designs. Full correction of refractive error was targeted. Refraction; best corrected visual acuity (BCVA); RPR (Shin-Nippon NVision-k 5001) along the horizontal and vertical meridians; and corneal topography (Medmont E300) were measured before starting lens wear and in the morning after lens removal after the seventh night of lens wear for both lens designs. TZ diameter and decentration was calculated from corneal topography.ResultsAfter 7-nights of wear both lens designs created -2.00D refraction effect with no significant difference in refractive effect or change to BCVA between the designs. The Test design created a significantly smaller horizontal (4.78 ± 0.37 vs 5.70 ± 0.37 mm, p < 0.001) and vertical (5.09 ± 0.51 vs 5.92 ± 0.51 mm p < 0.001) TZ diameter. The TZ was decentered inferior temporal with no significant difference between designs. There was no significant difference between the lens designs in RPR along the horizontal and vertical meridians at any measurement period.ConclusionsOK induced TZ diameter can be reliably reduced by altering OK lens design without detrimentally effecting lens centration or refractive effect. Reducing TZ diameter did not alter RPR, though measurement artifacts could be responsible for masking an effect. Longitudinal studies are needed to assess whether smaller TZ OK lens designs increase efficacy for slowing progression of myopia.     

浅析火力发电厂汽水系统中内径管与外径管的设计选择

按照管道加工工艺的不同,管道可分为内径控制管和外径控制管。通过热轧工艺生产的外径控制无缝钢管,可满足火力发电厂汽水系统中绝大部分管道的使用要求。对于超(超)临界机组的主蒸汽和高温再热蒸汽管道采用的P91/P92材质的大口径厚壁无缝钢管,由于对材料性能和加工工艺有特殊要求,因此宜采用内径控制管。     

天然气井作业屏蔽暂堵技术的研究与应用

在天然气井进行井下作业前，将暂堵剂挤入生产层位附近，以暂时封堵生产层，使地层压力不被释放，井筒内的压井液不污染地层，待施工作业结束后，及时进行解堵，确保天然气井不受伤害或少伤害，从而恢复天然气井的生产能力。针对天然气井大修作业时，经常补充压井液，由于作业时间长，大量压井液进入地层，造成严重污染，导致天然气井恢复生产困难的问题，研制出一种新型气井作业的屏蔽暂堵剂，具有污染小，易解堵等特点，有效解决了大修污染问题，现场应用取得良好效果。     

一种估算单桩经济直径的方法

在滩海油田开发过程中,经常需要设立立管桩,在环境荷载的作用下,立管桩顶部会发生位移,较大的位移对立管及栈桥的安全很不利,因此需要合理确定单桩的直径。埕岛油田在确定单桩直径时引入了经济直径的概念,文章对经济直径的原理进行了分析,给出了桩顶位移和桩径经济指数计算公式,并举例进行了计算,得出了桩径与桩顶位移及桩径经济指数的关系曲线, 进而求得经济桩径的取值范围。文章还对该方法的优缺点进行了分析。     

露天多段深孔微差爆破孔网参数优化设计

本文对露天多段深扎微差爆破孔网参数进行了优化，使每排炮扎成直线排列，两排之间成交替正三角形排列，优化设计后，爆破作用比较均匀，大块率下降了56％，同时，爆破根底产生的机会和程度也大大下降。     

WuM1-1羽状分支水平井充气钻井液技术

WuM1-1井由1口多分支水平井和1口采气的直井组成。该井斜井段短,井斜率在30°/100 m以上,主井眼和10个分支井段总进尺6182 m,98%以上在煤层中钻进,煤层脆、压实性较好,更易发生掉块。为满足钻井对井壁稳定性、润滑性、井眼净化以及煤层保护等的要求,采用钾铵基聚合物防塌钻井液进行充气欠平衡钻井,在钻进中保持钻井液有合适的粘度、切力,选用合适的注气压力和注气量以及当量钻井液密度;每钻完一个立柱坚持循环几分钟,上下划眼一次,并泵入CMC高粘钻井液,配合有效使用固控设备,尽量使井眼干净;复配使用粉末状固体润滑剂和液体润滑剂。该钻井液性能稳定,易于维护,悬浮携岩能力强,润滑性好,井眼畅通,保证了WuM1-1井安全、快速、优质施工。该井在煤层钻进中无阻卡现象,井壁稳定,没有出现井壁掉块或井垮现象,水平连通一次成功,10口分支井悬空侧钻一次成功,只用57 d即顺利完井,比该地区常规钻井快49倍。     

Efficient Parallel Algorithms for Some Graph Theory Problems

In this paper,a sequential algorithm computing the aww vertex pair distance matrix D and the path matrix Pis given.On a PRAM EREW model with p,1≤p≤n^2,processors,a parallel version of the sequential algorithm is shown.This method can also be used to get a parallel algorithm to compute transitive closure array A^* of an undirected graph.The time complexity of the parallel algorithm is O(n^3/p).If D,P and A^* are known,it is shown that the problems to find all connected components,to compute the diameter of an undirected graph,to determine the center of a directed graph and to search for a directed cycle with the minimum(maximum)length in a directed graph can all be solved in O(n^2/p logp)time.