了解您的管理跨度--科研项目管理方法探索

概要介绍了科学的管理技术——项目管理方法，讨论了管理跨度在项目管理中的重要性，并推荐了如何了解管理跨度的方法。     

太钢4号高炉喷煤站应用MFD—Ⅲ型布袋除尘器的实践

太钢４号高炉喷煤站从１９９０年起采用ＭＦＤ－Ⅲ型脉动反吹式布袋除尘器。这种除尘器采用脉动式反吹清灰设施，合理布置布袋间距，布袋支撑骨架及选用针呢材质的布袋，过滤面积大，反吹清灰效果好，设备运行平稳，除尘效率高达９９．８％，排放浓度小于１０ｍｇ／ｍ＾３，故障率低。     

A sensorless brushless dc motor system

This paper describes a brushless dc motor system without position or speed sensor. The brushless motor consists of a permanent magnet synchronous motor and a voltage-source inverter capable of controlling the amplitude and frequency of voltage. The rectangular-shaped stator current with a conducting interval of 120° (electrical) is controlled to be in phase with the trapezoidal back electromotive force. This results in producing maximum torque. Variable speed is achieved by adjusting the average motor voltage similarly to chopper control of dc motors. In this paper, two sensorless position detecting methods, i.e., an “indirect method” suited for the lower-speed range and a “direct method” suited for the higher-speed range are proposed. The combination of the two makes it possible to detect the rotor position over a wide-speed range. Furthermore, a speed-sen-sorless PLL control is proposed in applying the principle of the direct method. Experimental results obtained from a prototype brushless dc motor are shown to confirm the validity of the sensorless drive. The starting procedure of the motor also is discussed because it is impossible to detect the rotor position at a standstill.     

The concept of an endurance limit for adhesive joints

The effect of cyclic stressing on the strength of single lap adhesive joints has been studied and a considerable reduction in strength observed when the maximum stress exceeds about 40% of the ultimate tensile strength, but whether or not a true endurance limit exists is not proven. Fallacies are shown in some of the techniques which have been proposed for studying the fatigue behaviour of adhesive joints.     

最新水冷式全固态数字调幅600kW中波发射机

数字调幅制式是当前国际上较先进的调制技术，ＤＸ系列全固态数字调幅中波发射机的电声指标和工业效率都是很先进的，过去的ＤＸ大功率机采用风冷方式，本文介绍了最新水冷ＤＸ－６００发射机的设备情况和技术特点。     

对遂昌金矿采场结构参数的探讨

对于遂昌金矿合理的采场结构参数，目前没有理想的确定方法。本文联系上盘围岩的构造裂隙，矿房的支护形式等提出采场稳定跨度判断指标。经４０个采场的检验，值信度达９７．５％。     

反水锤的危害及防止

反水锤是发生在反击式水轮机尾水道中的一种特殊水锤现象，其压力峰值可达正常压力的几倍，甚至十多倍，以致造成肢解转轮、折断导叶、破坏顶盖、抬起转子的严重事故。因此，研究反水锤发生的原因，从而提出防止反水锤事故的措施尤为重要。     

轻钢结构浅析

轻钢结构作为一种新型结构在近几年发展很快，应用范围也日趋广泛。主要针对轻钢结构的特点，结合实际工程设计，对轻钢结构现状、发展进行了阐述和分析。     

瓦斯燃烧器回流区测试

燃烧器流场内回流区的大小和形状决定了燃烧火焰的稳定性 ,利用APV激光测速系统 ,在燃烧器冷态测试实验装置上对一瓦斯燃烧器冷态模型的流动进行了研究 ,发现了该燃烧器流场内的双回流区结构 ,并得到了中心回流区尺寸与稳焰器结构的关系 ,为该结构类型燃烧器的稳焰设计及稳焰能力的评价提供了实验依据     

不清根手工双面焊材料及工艺研究

本文分析了中厚板传统手工双面焊存在的诸如打底焊焊缝质量无法保证，需用碳弧气刨清根；工人劳动强度大；生产效率低；焊接质量不稳定等主要问题。为提高打底焊焊道质量，不用清根使背面得到良好的凹成形，研制了适合Ｘ形坡口的梯形体陶瓷衬垫。探讨了焊缝背面成形的主要影响因素及控制方法。