Crystal-field engineering of ultrabroadband mid-infrared emission in Co2+-doped nano-chalcogenide glass composites

Tunable and ultrabroadband mid-infrared (MIR) emissions in the range of 2.5–4.5 μm are firstly reported from Co²⁺-doped nano-chalcogenide (ChG) glass composites. The composites embedded with a variety of binary (ZnS, CdS, ZnSe) and ternary (ZnCdS, ZnSSe) ChG nanocrystals (NCs) can be readily obtained by a simple one-step thermal annealing method. They are highly transparent in the near- and mid-infrared wavelength region. Low-cost and commercially available Er³⁺-doped fiber lasers can be used as the excitation source. By crystal-field engineering of the embedded NCs through cation- or anion-substitution, the emission properties of Co²⁺ including its emission peak wavelength and bandwidth can be tailored in a broad spectral range. The phenomena can be accounted for by crystal-field theory. Such nano-ChG composites, perfectly filling the 3–4 μm spectral gap between the oscillations of Cr²⁺ and Fe²⁺ doped IIVI ChG crystals, may find important MIR photonic applications (e.g., gas sensing), or can be used directly as an efficient pump source for Fe²⁺: IIVI crystals which are suffering from lack of pump sources.     

Evaluation of the Properties of Si3N4/Si3N4 Joint Brazed Using a Filler Alloy Containing Pd

Si3N4 ceramic was jointed to itself using a filler alloy of Cu76.5Pd8.5Ti15, and the mechanical properties of the jointwere measured and analyzed. By using a filler alloy of Cu76.5Pd8.5Ti15, the SisN4/SisN4 joints were obtained bybrazing at 1373～1473 K f     

Wear and Creep Characteristics of a Carbon‐Derived Si3N4/SiC Micro/Nanocomposite

In the presented work some properties of a recently developed Si₃N₄/SiC micro/nanocomposite have been investigated. The material was tested using a pin on disc configuration. Under unlubricated sliding conditions using Si₃N₄ pin at 50 % humidity, the friction coefficient was in the range of 0,6 ‐ 0,7. The reduction of humidity resulted in a lower coefficient of friction, in vacuum the coefficient of friction had a value of about 0,6. The wear resistance in vacuum was significantly lower then that in air. The wear patterns on the Si₃N₄+SiC disc revealed that mechanical fracture was the wear controlling mechanism. Creep tests were realized in four point bending configuration in the temperature interval 1200‐1400 °C at stresses 50,100 and 150 MPa and the minimal creep deformation rate was established for each stress level. The activation energy, established from the minimal creep deformation had a value of about 360 kJ/mol and the stress exponent values were in the range of 0.8‐1.28. From the achieved stress exponents it can be assumed that under the studied load/temperature conditions the diffusion creep was the most probable creep controlling mechanism.     

用硫酸铁铵容量法测定钛精矿中二氧化钛含量

样品在过氧化钠熔融、水浸取及盐酸酸化后，在盐酸和硫酸介质中，隔绝空气，用金属铝将钛(Ⅳ)还原至钛(Ⅲ)，以硫氰酸盐为指示剂，用硫酸铁铵标准溶液滴定。     

Influence of ethyl methacrylate content on the volume‐phase transition of temperature‐sensitive poly[(N‐isopropylacrylamide)‐co‐(ethyl methacrylate)] microgels

A novel series of temperature‐sensitive poly[(N‐isopropylacrylamide)‐co‐(ethyl methacrylate)] (p(NIPAM‐co‐EMA)) microgels was prepared by the surfactant‐free radical polymerization of N‐isopropylacrylamide (NIPAM) with ethyl methacrylate (EMA). The shape, size dispersity and volume‐phase transition behavior of the microgels were investigated by transmission electron microscopy (TEM), ultraviolet–visible (UV–Vis) spectroscopy, dynamic light scattering (DLS) and differential scanning calorimetry (DSC). The transmission electron micrographs and DLS results showed that microgels with narrow distributions were prepared. It was shown from UV–Vis, DLS and DSC measurements that the volume‐phase transition temperature (VPTT) of the p(NIPAM‐co‐EMA) microgels decreased with increasing incorporation of EMA, but the temperature‐sensitivity was impaired when more EMA was incorporated, causing the volume‐phase transition of the microgels to become more continuous. It is noteworthy that incorporation of moderate amounts of EMA could not only lower the VPTT but also enhance the temperature‐sensitivity of the microgels. The reason for this phenomenon could be attributed to changes in the complicated interactions between the various molecules. Copyright © 2004 Society of Chemical Industry     

单微乳液中制备Ag/TS-1及丙烯气相环氧化

采用N2H4还原含AgNO3的单微乳液制备了Ag／TS-1催化剂。TEM表征结果表明，Ag高度分散于TS-1之上。以H2、O2存在下的丙烯气相环氧化为探针反应，考察了Ag／TS-1的催化性能。结果表明，采用Ag／TS-1为催化剂，Ag的负载量为1％（质量分数，下同），823 K焙烧后，373 K下反应30 min时，丙烯转化率为1．69％，环氧丙烷（Propylene oxide，PO）选择性为93．2％。当Ag的负载量超过2％时，反应过程中生成大量的热，造成PO的选择性下降。采用Ag的负载量为8％的Ag／TS-1催化剂，消除热效应后，丙烯的转化率为2．46％．PO的选择性为79．2％。     

A family of lower- and higher-order transversal linearization techniques in non-linear stochastic engineering dynamics

Sample pathwise numerical integration of noise-driven engineering dynamical systems cannot generally be performed beyond a limited level of accuracy, especially when the noise processes are modelled using (filtered) white noises. Recently, a locally transversal linearization (LTL) strategy has been proposed by the author (Proc Roy Soc London A 2001; 457 :539–566) for direct integration of deterministic and stochastic non-linear dynamical systems. The present effort is focussed on a host of extensions along with detailed theoretical error analyses of the linearization approach, especially as applied to problems in non-linear stochastic engineering dynamics. Thus, to begin with, estimates of local and global error orders in the basic LTL scheme are obtained separately for the displacement and velocity vectors when the system is driven either by a set of additive noises or by an arbitrary combination of (independently evolving) additive and multiplicative noises. Following this, a new family of higher-order LTL schemes is proposed in order to improve upon the basic LTL method and the associated error orders are established. A stepwise implementation of the lower- and higher-order versions of the LTL method, along with certain computational aspects, is also outlined. The proposed schemes are numerically illustrated, to a limited extent, for a single degree-of-freedom (SDOF) and a two degree-of-freedom (TDOF) non-linear engineering systems under additive and/or multiplicative white noise excitations. Copyright © 2004 John Wiley & Sons, Ltd.     

Effect of Y2O3, CeO2 on Sintering Properties of Si3N4 Ceramics

The effect of rare earth oxides Y203 or Ce02 on sintering properties of Si3N4 ceramics was studied and the mechanism of assisting action during sintering was analyzed. The results in dicate that the best sintering properties appear in Si3N4 ceramics with 5% Y203 or 8% CeO2. Secondary crystallites are formed at grain boundaries after heat treatment,which decreases the amount of glass phase and contributes to the improvement of high-temperature mechanical properties of silicon nitride.     

Catalytic reduction of N2O with CH4 and C3H6 over Ag–Rh/Al2O3 bimetallic catalyst in the presence of oxygen

A study of nitrous oxide (N₂O) reduction with methane (CH₄) and propene (C₃H₆) in the presence of oxygen (5%) over Ag/Al₂O₃, Rh/Al₂O₃ and Ag–Rh/Al₂O₃ catalysts, with Ag and Rh loadings of 5 wt% and 0.05 wt% respectively, has been performed. From the results, it was observed that the Ag–Rh bimetallic catalyst was the most active for both nitrous oxide removal (more than 95%) and hydrocarbon oxidation. This high activity seems to be connected with a synergistic effect between Ag and Rh. The findings from X‐ray diffraction and X‐ray photoelectron spectroscopy studies showed also, that there were no strong interactions (eg alloying) between Ag and Rh. Copyright © 2005 Society of Chemical Industry