Temperature cycling and its effect on mechanical behaviours of highporosity chalks

Temperature history can have a significant effect on the strength of water-saturated chalk.In this study,hydrostatic stress cycles are applied to understand the mechanical response of chalk samples exposed to temperature cycling between each stress cycle,compared to the samples tested at a constant temperature.The total accumulated strain during a stress cycle and the irreversible strain are reported.Chalk samples from Kansas(USA)and Mons(Belgium),with different degrees of induration(i.e.amount of contact cementation),were used.The samples were saturated with equilibrated water(polar)and nonpolar Isopar H oil to quantify water weakening.All samples tested during 10 stress cycles with varying temperature(i.e.temperature cycled in between each stress cycle)accumulated more strain than those tested at constant temperatures.All the stress cycles were performed at 30℃.The two chalk types behaved similarly when saturated with Isopar H oil,but differently when saturated with water.When saturated with water,the stronger Kansas chalk accumulated more total strain and more irreversible strain within each stress cycle than the weaker Mons chalk.     

乘累加运算器的高性能解决方案

在设计数字信号处理器时我们经常要设计高性能的乘累加运算器，文章详细分析了乘累加运算器的结构，提出了其高性能设计方案并采用标准单元进行了实现，同时提出了DCT运算单元的高性能解决方案。     

沙漠生物结皮土壤发育特征的研究

通过对沙漠生物结皮层相关的土壤特性研究表明,结皮层不仅具有明显的养分富集和细粒物质的聚集作用,而且结皮层腐殖质成份的含量以及其分子结构和复杂程度也在增加。腐殖质光学特性的变化趋势明显反映了不同地区结皮层土壤发育的地带性特征。结皮层持水量明显高于沙层,并对降水再分配有一定影响。     

珠江口盆地开平凹陷油气聚集条件分析

珠江口盆地自新生代以来,曾先后受到不同方向张应力的作用,造成了不同时期构造体系的交叉叠合.中中新世以来构造运动强烈,并具有东强西弱的特点,对油气的运移与聚集产生了重要影响.开平凹陷的剧烈断裂和断陷活动始于始新世,并在同期沉积了巨厚的文昌组.晚渐新世以后,由于断裂活动非常微弱,在成熟的烃源岩与其上地层之间缺乏有效的油源断层,因而自生自储、近距离运移可能是开平凹陷油气聚集的基本特征.在凹陷内部,因重力滑动和欠压实泥岩共同作用所形成的KPll-1构造带可能是该区最具有油气远景的地区.     

An investigation of the unstable region for dense phase conveying in sliding bed flow

For fine powdered materials, capable of being conveyed in dense phase, a conveying region exists in which instability in flow and pipeline blockage can occur if the pressure gradient available is insufficient to maintain a minimum value of solids loading ratio. A reduction in material flow rate can also lead to pipeline blockage in this region. Conveying trials under-taken with cement are used to illustrate the nature of the problem.     

Continuous formation of slurry ice by cooling water–oil emulsion in a tube

Water-silicone oil emulsion with an additive, (C₂H₅O)₃SiC₃H₆NH₂, was examined as a heat storage material. A spiral tube used as a heat exchanger was immersed in a low temperature bath and the emulsion was circulated in the tube to make ice continuously. Ice was separated from the ice–liquid suspension in an outlet tank. The amount of formed ice, the temperatures of the inlet and the outlet of the heat exchanger, and the temperatures in the tube wall were measured and the overall heat transfer coefficient and the heat flux through the tube were calculated. Experiments were carried out, varying the flow rate, the temperature of cooling brine, and the thickness of tube wall. The condition under which slurry ice was formed continuously without adhesion of ice to the cooling wall was clarified. Though decrease in the thermal resistance of the tube increased the rate of ice formation or raised the brine temperature, it narrowed the range of the flow rate and of the brine temperature in which slurry ice was formed continuously.     

城市燃气管网设计若干问题的探讨

分析了哈依燃气管道工程在施工及管理过程中存在的问题，并就如何解决这些问题提出了建议。     

Paste Residence Time in a Spouted Bed Dryer. III: Effect of Paste Properties and Quality Interactions

The aim of this study was to evaluate the effects of paste properties on residence time during drying in a spouted bed dryer with inert bodies. The effect of paste solids content, surface tension, and viscosity on the residence time distribution and the mean residence times were studied using factorial experimental designs. The inert bodies used were glass and polyethylene beads. The mean residence times varied from 13.6 to 16.3 and 12.2 to 17.7 min for drying on glass and polyethylene beads, respectively. The analysis of variance showed that mean residence times significantly depended on solids content and surface tension for glass beads and also on viscosity for polyethylene beads. The residence time distributions for all conditions studied fitted well to the perfect mixing cell when applying the continuous stirred vessels in series model analysis. The powder density, flowability, and particle size depended on paste properties and inert type.