粉体含能材料生产与储运中的静电安全及防护

分析了静电产生的原因,阐述了粉体含能材料生产中的静电起电现象、静电的危害、静电安全性评估标准以及建立在此标准基础上的静电放电危险的评价办法,提出了粉体含能材料在生产、运输中所需要采取的静电防护措施。     

Modification of platinum surfaces by spontaneous deposition: Methanol oxidation electrocatalysis

The presence of a second metal on platinum surfaces affects the performance of methanol oxidation. However, most of the electrocatalytic reactions are studied by using electrochemically deposited platinum alloys, but in the case of spontaneous deposition the situation is not so clear since the surface distribution, stability and morphology are usually not well documented. The formation of surface decorated samples on mono- and poly-crystalline platinum is followed by electrochemical and spectroscopic techniques and analysis of their performance towards methanol adsorption and oxidation compared with that on pure platinum. Pt/Sn and Pt/Ru are of special interest because of their well-known performance in methanol fuel cells. Methanol oxidation on Pt(111)/Ru, Pt(111)/Sn and Pt(111) shows that ruthenium is the only one able to promote the reaction since the simultaneous dissolution of tin occurs and competes with the process of interest. The in situ infrared spectroscopy is used to compare methanol oxidation on Pt(111)/Ru and Pt(111) in acid media using p-polarized light. The formation of bridge bound carbon monoxide is inhibited in the presence of ruthenium ad-species, whereas on Pt(111) the three adsorption configurations are observed. Linear sweep polarization curves and Tafel slopes (calculated from steady state potentiostatic plots) for methanol oxidation are compared on polycrystalline surfaces modified by tin or ruthenium at different coverages. There is almost no change in the Tafel slopes due to the presence of the foreign metal except for Pt/Ru, where a 0.09 V decade⁻¹ slope was calculated below 0.55 V due to hydroxyl adsorbates on ruthenium islands. The anodic stripping of methanol residues on the three surfaces indicates a lower amount of carbon monoxide-type adsorbates on Pt/Ru, and the simultaneous tin dissolution process leading to residues oxidation on Pt/Sn electrodes.     

改性生物质作为型煤黏结剂的研究

探讨了用NaOH改性生物质秸秆作为型煤黏结剂的可行性,考察了NaOH溶液浓度对生物质改性的影响以及生物质添加量、无机物(MgO和MgCl2)添加量对型煤机械强度、防水性能和着火温度的影响。研究结果表明,NaOH改性液的质量分数为1.0%~2.0%时,制得的生物质型煤有较高的机械强度;生物质添加量在2%~20%时,随生物质添加量的增加,机械强度增加,着火温度降低,但防水性较差;而在生物质型煤中加入适量无机黏结剂后,型煤有很高的浸水强度,表现出优越的防水性能。     

Preparation of clean coal by flotation following ultra fine liberation

This paper reports the results of current fundamental research at the Department of Process Engineering, University of Miskolc on the processing of clean coal from Mecsek bituminous coal, Southern Hungary. The theoretical possibility of the separation of different petrographic components was proven experimentally and their liberation degree was determined based on the petrographic composition, flotation kinetic study of isolated components (groups of components), scanning electron microscopy and microprobe analyses. The mill with stirred ball media was chosen for the ultra-fine liberation of the coal components. It was revealed that along with the liberation of coal components, their surface oxidation and spontaneous agglomeration, entrapping the mineral impurities take place in ultra-fine grinding. This paper discusses the interfacial phenomena occurring in the ultra-fine grinding process and their influence on the flotation. The concept for the advanced preparation of clean coal was developed, tested and proved. The main steps of this concept are the ultra-fine liberation in the stirred-media mill, the de-agglomeration of flocs spontaneously formed during the ultra-fine grinding and the induced (hydrophobic) flocculation with the following two-step flotation in a flotation column.     

烧结富氧点火自动控制的实现与应用

介绍了长钢烧结厂在24m^2烧结机上采用富氧点火自动控制的实现与应用。     

工业炉燃烧系统应用技术探讨

燃烧及其控制技术是各种火焰炉技术核心，强调高水平燃烧系统应对燃烧全过程进行控制，着重对燃烧系统点火、火焰监测、空燃比比例调节、燃烧过程各参数监控、炉温自动控制等各个方面内容进行了讨论介绍，最后用某天然气加热炉燃烧系统原理图及应用效果进行实例说明。     

火烧油层技术在庙5块低渗透稠油油藏中的应用

方法在物理模拟的基础上，利用数值模拟及油藏工程方法，对影响火烧油层的技术参数进行了优选研究，并对影响火驱成败的油藏地质参数、注气参数进行了分析。目的寻找适合庙５块低渗透稠油油藏的开采方法。结果提出了庙５块火驱的最佳开采方式、点火参数及注气参数；庙５块火驱生产后，平均单井日产液由０１ｔ上升到５６ｔ，平均单井日产油由０１ｔ上升到３５ｔ，生产２６ｄ后由于压风机供风不足被迫停止火驱注气；从数模结果看：火驱最终采收率可达３９８％。结论火烧油层是一种潜力很大的稠油开采方法，但其物理、化学反应机理复杂，火烧前缘难以控制；庙５块火驱初期虽然见到了一定的生产效果，但没有取得经济效益     

氯酸钾－木炭系与铅丹－硅系引火药头对铁脚线桥脚锈蚀的影响

文中分析和探讨了氯酸钾－木炭系引火药头的锈蚀问题，进而提出了铅丹－硅系引火药头，并经贮存实验表明后者对于克服前者的锈蚀问题有明显的作用。     

硫化矿石氧化性的实验室综合评判

探讨了一种硫化矿石氧化性综合评判的新方法 ,并将该方法应用于矿山实际 ,得到了准确的评判结果。该项成果对于硫化矿石自燃防治理论与技术的研究具有很高的参考价值。     

静电火灾的产生及其防治

文章详细分析了静电产生的机理，指出积聚静电电荷的多少与材料的电阻率和介电常数有关。讨论了静电火灾发生的条件，指出静电火灾的发生具有隐蔽性、复杂性和突发性。但只要对其规律进行深入地研究，可以找到有效地防止静电火灾发生的办法。