Equal Strain Consolidation by Vertical Drains

This paper shows the development of a series of closed-form solutions of equal strain consolidation in the presence of a vertical drain with smear and well resistance. Using an approach that considers the effects of both the radial and vertical drainage in a fully coupled fashion, solutions are obtained for the excess pore pressure and the degree of consolidation in the compressible soil subjected to a step- or ramp-loading situation. The closed-form solutions in the present paper may be evaluated in an electronic spreadsheet on a standard personal computer.     

Internally humidified polymer electrolyte fuel cells using water absorbing sponge

Polymer electrolyte fuel cell (PEFC) mounted with two strips of polyvinyl alcohol (PVA) sponge is presented and the effect of operating conditions on the cell performance is investigated. Mounting the sponge wicks is advantageous for the humidification of dry inlet air and for the removal of liquid water in the cell. It was found that dry inlet hydrogen could be internally humidified by water diffusion from the cathode to anode when operating in a counterflow mode. The results show that the relative humidity of the inlet gases could have little effect on the performance of the cell mounted with two sponge wicks under certain operating conditions. At a cell potential of 0.5 V, the current densities of the sponge-mounted PEFC operated with dry air are 5% and 31% higher than those of the conventional one without wicks operated with saturated and dry air, respectively. The molar percentage of water vapor to total water exiting the cathode (R_gas) is an important parameter to gauge the cell performance with dry gases. A very large R_gas may cause the membrane dehydration and subsequently a low cell performance.     

Current distribution in polymer electrolyte membrane fuel cell with active water management

Air delivery is typically the greatest parasitic power loss in polymer electrolyte membrane fuel cell (PEMFC) systems. We here present a detailed study of an active water management system for PEMFCs, which uses a hydrophilic, porous cathode flow field, and an electroosmotic (EO) pump for water removal. This active pumping of liquid water allows for stable operation with relatively low air flow rates and low air pressure and parallel cathode channel architectures. We characterize in-plane transport issues and power distributions using a three by three segmented PEMFC design. Our transient and steady state data provide insight into the dynamics and spatial distribution of flooding and flood-recovery processes. Segment-specific polarization curves reveal that the combination of a wick and an EO pump can effect a steady state, uniform current distribution for a parallel channel cathode flow field, even at low air stoichiometries (α_air = 1.5). The segmented cell measurements also reveal the mechanisms and dynamics associated with EO pump based recovery from catastrophic flooding. For most operating regimes, the EO pump requires less than 1% of the fuel cell power to recover from near-catastrophic flooding, prevent flooding, and extend the current density operation range.     

喷气织机主喷嘴气流性能的测试与分析

在SX-1型喷气织机测试仪上,对常用的几种主喷嘴进行了淹没射流测试,揭示了主喷嘴射流压力衰减率与射流距离及喷嘴芯内径的关系,认为调节主喷嘴喷嘴芯的转角对主喷气流的压力、风速及对纬纱的牵引力影响不大,主喷嘴气流压力衰减率存在一个峰值,要慎重选择喷嘴芯的内径.     

一类量子随机微分方程的解

借助Hida度degT,给出了由量子噪声驱动的Wick型量子随机Cable方程在广义算子水平上存在唯一连续解的另一充分条件.     

Experimental study on the thermal performance of a small-scale loop heat pipe with polypropylene wick

A small-scale loop heat pipe (LHP) with polypropylene wick was fabricated and tested for investigation of its thermal performance. The container and tubing of the system were made of stainless steel and several working fluids were tested including methanol, ethanol, and acetone. The heating area was 35 mm×35 mm and nine axial grooves were provided in the evaporator to provide vapor passages. The pore size of the polypropylene wick inside the evaporator was varied from 0.5 μm to 25 μm. The inner diameter of liquid and vapor transport lines were 2.0 mm and 4.0 mm, respectively and the length of which were 0.5 m. The size of condenser was 40 mm (W) ×50 mm (L) in which ten coolant paths were provided. Start-up characteristics as well as steady-state performance was analyzed and discussed. The minimum thermal load of 10W (0.8W/cm²) and maximum thermal load of 80 W (6.5W/cm²) were achieved using methanol as working fluid with the condenser temperature of 20°C with horizontal position.     

Stochastic Models of Financial Mathematics

Stochastic Cox-Ingersoll-Ross differential equations and Hull-White equations (Vasicek and Cox-Ingersoll-Ross extensions) are investigated. Two approaches to the solution of such equations are considered. The results of these investigations allow one to determine a short-term rate in a securities market.     

In situ-polymerized wicks for passive water management in proton exchange membrane fuel cells

Air-delivery is typically the largest parasitic loss in PEM fuel cell systems. We develop a passive water management system that minimizes this loss by enabling stable, flood-free performance in parallel channel architectures, at very low air stoichiometries. Our system employs in situ-polymerized wicks which conform to and coat cathode flow field channel walls, thereby spatially defining regions for water and air transport. We first present the fabrication procedure, which incorporates a flow field plate geometry comparable to many state-of-the-art architectures (e.g., stamped metal or injection molded flow fields). We then experimentally compare water management flow field performance versus a control case with no wick integration. At the very low air stoichiometry of 1.15, our system delivers a peak power density of 0.68 W cm⁻². This represents a 62% increase in peak power over the control case. The open channel and manifold geometries are identical for both cases, and we demonstrate near identical inlet-to-outlet cathode pressure drops at all fuel cell operating points. Our water management system therefore achieves significant performance enhancement without introducing additional parasitic losses.     

Mathematical modeling of an inclined solar water distillation system

An inclined solar water distillation (ISWD) system, which generates distilled water (i.e., condensate) and hot water at the same time, was modeled and simulated. In the parametric studies, the effects of feed water mass flow rate and solar intensity on the system parameters were investigated. Finally, the system was simulated using actual deviations of solar intensity and environment temperature during a typical summer day in North Cyprus. The system can generate 3.5–5.4 kg (per m² absorber plate area) distilled water during a day (i.e., 7 am till 7 pm). The temperature of the produced hot water reached as high as 60°C, and the average water temperature was about 40°C, which is good enough for domestic use, depending on the type of feed water. The simulation results are in good agreement with the experimental results.     

Flame retardant synergy between interfacial and bulk carbonation in glass fiber reinforced polypropylene

Glass fiber reinforced polypropylene (GF-PP) composites have high flammability on account of wick effect which leads to accelerated flow of the polymer melt along the glass fibers (GF) surface to the flame zone. In this study, dipentaerythritol (DPER), a charring agent, was adsorbed on the GF surface through the hydrogen bond between silane coupling agent and DPER. DPER has a synergistic effect with the intumescent flame retardants (IFR) added in the composites, which can induce interfacial carbonization on the surface of GF, thus transforming the intrinsic smooth GF surface into roughness one. In this way, the negative effect of the wick effect in flame retardancy is weakened. Moreover, the char residues remained on the surface of GF can bring an improved adhesion between GF and char residues formed in the resin so that a more stable barrier char layer is formed. The PP composites with 20 wt% modified glass fiber (M-GF) and 30 wt% IFR can achieve the UL-94V-0, and its limiting oxygen index (LOI) value increased from 16.5% to 29.5%. Simultaneously, the heat release rate (HRR), total heat release (THR) and total smoke release (TSR) decreased significantly, and the peak of heat release rate (PHRR) reduced 60.6% compared with GF-PP.