Formation process of zirconia nanotubes and porous structures and model of oxygen bubble growth

Preparation and growth mechanism of anodization of Ti and Al has been widely concerned for two decades, but the research on anodic ZrO₂ is relatively lacking. In this paper, anodic TiO₂ and ZrO₂ nanotubes were prepared in glycerol electrolyte containing 0.35 M NH₄F and 4 vol% H₂O under different anodizing voltages. We had successfully prepared the anodic ZrO₂ nanotubes (AZNTs) with a complete top and a “bulb” at the bottom under 60 V, and with the increase of the applied anodizing voltage, the “bulb” cavity also increased. However, under the same anodizing conditions, the surface of anodic TiO₂ nanotubes (ATNTs) is a cluster of nano-tip morphology, and the bottom of the ATNTs is a conventional hemisphere shape. In addition, both AZNTs and porous anodic zirconia (PAZ) were found to coexist in the anodic ZrO₂ layer prepared at 60 V. Here, we used the oxygen bubble model and ionic current and electronic current theories to analyze the reason of the special morphology. It is confirmed that the porous anodic oxides are actually evolved from nanotubes. In other words, the structure is essentially the same.     

Development and validation of a micro-fin tubes evaporator model using R134a and R1234yf as working fluids

This paper presents a model of shell and tube evaporator with micro-fin tubes using R1234yf and R134a. The model developed for this evaporator uses the ε-NTU method to predict the evaporating pressure, the refrigerant outlet enthalpy and the outlet temperature of the secondary fluid. The model accuracy is evaluated using different two-phase flow boiling correlations for micro-fin tubes and comparing predicted and experimental data. The experimental tests were carried out for a wide range of operating conditions using R134a and R1234yf as working fluids. The predicted parameter with maximum deviations, between the predicted and experimental data, is the evaporating pressure. The correlation of Akhavan– Behabadi et al. was used to predict flow boiling heat transfer, with an error on cooling capacity prediction below 5%. Simulations, carried out with this validated model, show that the overall heat transfer coefficient of R1234yf has a maximum decrease of 10% compared with R134a.     

掺气减蚀保护作用的新概念

利用针式掺气流速仪测量原型和模型掺气浓度场、流速场，气泡尺寸及其概率分布的研究成果表明，原型水流韦伯数高，形成微小气泡的能力比模型强，气泡上浮慢，接近底部的小尺寸气泡概率及掺气浓度比模型大。初步研究认为：0.2mm或0.5mm以下的微小气泡在掺气减蚀中起着主要作用，可能只要很小掺气浓度即可达到掺气减蚀的效果。因此以小尺寸气泡的掺气浓度，作为判断掺气减蚀保护作用的指标将更为准确。     

Augmentation of boiling heat transfer from horizontal cylinder to liquid by movable particles

This paper presents a series of experimental results on a passive augmentation technique of boiling heat transfer by supplying solid particles in liquid. A cylindrical heater 0.88 mm in diameter is placed in saturated water, in which a lot of mobile particles exist, and the nucleate and film boiling heat transfer characteristics are measured. Particle materials used were alumina, glass, and porous alumina, and the diameter ranged from 0.3 mm to 2.5 mm. Particles are fluidized by the occurrence of boiling without any additive power, and the heat transfer is augmented. The maximum augmentation ratio obtained in this experiment reaches about ten times the heat transfer coefficient obtained in liquid alone. The augmentation ratio is mainly affected by the particle material, diameter, and the height of the particle bed set at no boiling condition. The augmentation mechanism is discussed on the basis of the experimental results. © 2001 Scripta Technica, Heat Trans Asian Res, 31(1): 28–41, 2002     

气泡在粘弹性液体中溶解的研究进展

在发泡塑料的制造过程中，均相气体－聚合物体系的形成直接影响了制品的物理机械性能，因此了解气泡在粘弹性液体中的溶解机理成为必然。本文讲述了气泡在流体中塌陷行为的研究进展。对Rayleigh对低粘度牛顿流体，Foqer和Goddand在无线量线性Maxwell模型的粘弹性体，Tanasawa和Tang用oldroyd三常数粘弹模型等科学家的研究行为做了概述，总结出影响此过程的复杂的影响因素，并指出进一步的研究方向。     

复合乳化沥青的粘附性试验方法研究

鉴于目前使用的阳离子乳化沥青粘附性试验方法难以有效评价复合乳化沥青粘附性，通过试验研究并综合考虑乳化沥青施工和路用实际情况，提出了乳化沥青水煮法试验方法和采用该方法检验复合乳化沥青粘附性时的评定标准。     

核反应堆加热流道含汽量计算研究

指出了加热流道内含汽量传统算法中存在的问题 ,并提出了新的算法     

Modeling for local dynamic behaviors of phenol biodegradation in bubble columns

A coupled three-dimensional (3-D) model, combining hydrodynamics with biochemical reactions, was developed to simulate the local transient flow patterns and the dynamic behaviors of cell growth and phenol biodegradation by yeast Candida tropicalis in the bubble-column bioreactor, using the computational fluid dynamic (CFD) method. In order to validate this proposed model effectively, the validation of the local hydrodynamic characteristics of the gas-mineral salt solution (gas-liquid) two-phase system, with the phenol concentration of 1200 mg/L, and with the absence of cells, was performed in a square-sectioned bubble column bioreactor using the LDA system and conductivity probe. Furthermore, the validation of phenol biodegradation behaviors by yeast Candida tropicalis at different initial concentrations of phenol and cell was also carried out in the above bubble-column bioreactor. The results indicated that the model simulations had a satisfying agreement with the experimental data. Finally, the local instantaneous flow and phenol biodegradation features including gas holdup, gas velocity, liquid velocity, cell concentration and phenol concentration inside the bioreactor were successfully predicted in different-scale bubble columns by the proposed model. © 2006 American Institute of Chemical Engineers AIChE J, 2006     

太钢不锈冷轧工程防腐蚀施工技术

防腐蚀施工工艺掌握的好坏，直接影响到工程投入生产后的使用寿命，为保证工程质量，以太钢不锈冷轧改造工程冷线防腐为例，对其常发生的质量通病进行认真分析，总结出一套行之有效的施工技术。