Mechanical properties,corrosion resistance,and rubber pad forming of cold differential speed-rolled pure titanium for bipolar plates of proton-exchange membrane fuel cells

Due to problems such as pores on surface-treated coatings, the corrosion resistance of pure titanium bipolar plates for proton-exchange membrane fuel cells can be further improved by increasing the corrosion resistance of pure titanium by using differential speed-rolling (DSR); however, these materials have not yet reached the standard requirements of bipolar plates (corrosion current density i_corr＜10³ nA·cm^?2). In this work, the corrosion resistance of pure titanium was improved by optimizing the DSR process while the strength was maintained. The best corrosion resistance of the DSR pure titanium was achieved when the roller speed ratio was 2, while i_corr was 429 nA·cm^?2 in a solution of 0.5 M H₂SO₄ and 2 mg/L HF at room temperature. The formability of the DSR pure titanium for bipolar plates was verified. The optimal holding pressure range was 6.8–7.0 kN.     

Investigation of stress fields for non-standard sized glass plates loaded by ring-on-ring

A ring-on-ring (ROR) test is a prevailing test method for evaluating the equi-biaxial strength of glass materials. However, current ROR test standards limit the strength and size of glass to prevent a nonlinear behavior. In this study, the feasibility of ROR testing for non-standard, high-strength glass, such as tempered or ion-exchanged rectangular glass is investigated. To this end, ROR simulation based on theory and experiment is conducted for thirty non-standard glasses with widths of 100–300 mm and aspect ratios of 1.0–2.0. As a result, the maximum measurable stress was about 215.6 MPa for 100 × 200 mm glass and 481.3 MPa for 300 × 600 mm glass with a 3% deviation, which is well above the strength of regular tempered glass. The main purpose of this work is to understand the range of aspect ratio of horizontal and vertical widths of a glass plate that can be evaluated by the standard ROR test.     

钢管套筒灌浆连接轴向受拉性能模拟试验研究

为研究钢管套筒灌浆连接轴向受拉破坏过程及破坏机理，试验中设计了16组48个钢管套筒灌浆连接试件，试件采用钢板代替圆钢管，并进行静载试验。分析了灌浆料裂缝扩展过程、荷载-相对位移曲线，并对抗剪键高距比、灌浆料厚度、侧向力等因素对破坏过程及承载力的影响进行分析。结果表明：对于不设置抗剪键的套筒灌浆连接试件，斜裂缝随机产生，裂缝分布不均匀；对于设置抗剪键的套筒灌浆连接试件，裂缝首先出现在底部抗剪键位置处，与水平方向夹角约为30°，随后在中部和上部抗剪键位置处分别出现斜裂缝。由于每个抗剪键上荷载分担并不均匀，与抗剪键接触的灌浆料逐渐达到极限压应力，达到极限状态时，承载力全部由抗剪键间的机械咬合力承担，在连接承载力中，可忽略摩擦力和胶结力作用。随着抗剪键高距比h/s增大，各试件初始剪切刚度相差不大，承载力增大，但增幅逐渐减小，建议抗剪键高距比0.06g/s>0.3，同时需要满足灌浆料灌注的施工要求。     

The analysis and comparison of two novel kinds of focusing elements as reflectors

In this article, two novel kinds of focusing elements as reflectors are analyzed and compared. One is the grooved Fresnel zone plate reflector with continuous phase‐correcting. The other called subzone paraboloid reflector, has the profile that consists of a series of paraboloids. Their diffraction efficiencies and bandwidths are described. The two elements still preserve the advantages of Fresnel zone plates, namely, low profile, high efficiency, and simple fabrication. Two dual‐reflector antennas using the proposed focusing elements as the main reflectors are simulated and the results show that these antennas have good radiation performances. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:101–108, 2015.     

Thermal imaging of time-varying longitudinal defects in the internal coating of a tube

We deal with the mathematical model of the incremental degradation of the internal coating (e.g. a polymeric material) of a metallic pipe in which a fluid flows relatively fast. The fluid drags solid impurities so that longitudinal scratches, inaccessible to any direct inspection procedure, are produced on the coating. Time evolution of this kind of defects can be reconstructed from the knowledge of a sequence of temperature maps of the external surface. The time-varying orthogonal section of this damaged interface is determined as a function of time and polar angle through the identification of a suitable effective heat transfer coefficient by means of Thin Plate Approximation.     

A Lattice Approach to Image Segmentation

After a formal definition of segmentation as the largest partition of the space according to a criterion σ and a function f, the notion of a morphological connection is reminded. It is used as an input to a central theorem of the paper (Theorem 8), that identifies segmentation with the connections that are based on connective criteria. Just as connections, the segmentations can then be regrouped by suprema and infima. The generality of the theorem makes it valid for functions from any space to any other one. Two propositions make precise the AND and OR combinations of connective criteria. The soundness of the approach is demonstrated by listing a series of segmentation techniques. One considers first the cases when the segmentation under study does not involve initial seeds. Various modes of regularity are discussed, which all derive from Lipschitz functions. A second category of examples involves the presence of seeds around which the partition of the space is organized. An overall proposition shows that these examples are a matter for the central theorem. Watershed and jump connection based segmentations illustrate this type of situation. The third and last category of examples deals with cases when the segmentation occurs in an indirect space, such as an histogram, and is then projected back on the actual space under study. The relationships between filtering and segmentation are then investigated. A theoretical chapter introduces and studies the two notions of a pulse opening and of a connected operator. The conditions under which a family of pulse openings can yield a connected filter are clarified. The ability of segmentations to generate pyramids, or hierarchies, is analyzed. A distinction is made between weak hierarchies where the partitions increase when going up in the pyramid, and the strong hierarchies where the various levels are structured as semi-groups, and particularly as granulometric semi-groups. The last section is based on one example, and goes back over the controversy about “lattice” versus “functional” optimization. The problem is now tackled via a case of colour segmentation, where the saturation serves as a cursor between luminance and hue. The emphasis is put on the difficulty of grouping the various necessary optimizations into a single one.     

沉管隧道水下最终接头施工技术初探

简述了沉管隧道水下最终接头施工技术的应用现状，结合具体隧道工程实例，从外模工程、混凝土结构两方面介绍了最终接头施工技术，表明了该技术具有运用价值。     

开关电源的平均电流自动均流技术

针对多个开关电源并联时易出现负载电流在各模块间分配不均的现象,介绍了常用的负载电流自动均流法——平均电流自动均流法及其工作特性。并针对其存在母线电压降低的缺陷,提出了一种改进的平均电流自动均流方法,经试验证明均流精度比较高。     

热镀锌板(卷)工程设计中的环境保护问题

对热镀锌板(卷)的生产工艺、主要生产设备进行了简要介绍，并就其污染源(工序)、生产过程中产生的污染物及其控制措施进行了评述，同时就设计和生产中宜注意的几个环保问题进行了分析。     

规整填料和新型塔板设计参数选取的质疑及分析

笔者指出了目前规整填料和新型塔板设计计算中若干尚未完全解决的、有争议或值得进一步完善的设计参数。如:规整填料的每米理论板数、最小液体喷淋密度、最小气体空塔动能因子、新型塔板开孔率等,并提出了具体的设计方案供与同行切磋。