Range of the Applicability of the Wilkins Method to the Investigation of the Dynamic Stress-Strain State of Anisotropic Elastic Axisymmetric Shells

The exactness and stability of the Wilkins method in the investigation of the stress-strain state of axisymmetric anisotropic elastic shells, including thick-walled ones, have been studied for different values of artificial viscosity, pulse load rise and fall time, and different deformation process durations. A comparison of numerical calculations, performed by means of an application software package developed by V. A. Romashchenko on the basis of the Wilkins method, with experimental results, known numerical data, and with calculations using the computation kernel LS-DYNA 3D has been carried out.     

结构-波浪-海床耦合系统中大圆筒结构的波压力响应

以沉入式大圆筒结构为对象，通过设计随机波浪水槽实验，测取了在单筒和连续筒两种结构型式、两种沉入深度和两种波谱输入下结构表面的动波压力分布。波面高度以及波压力历程均在领域进行分析。通过计算结构表面沿高程和沿环向的波压力谱及波压力传递函数，将单筒实测结果与基于线性绕射理论的解析解进行了比较，同时也详细对比了两种结构型式下的实测结果。文中汇报了在研究中获得的新发现及进行的相应分析，特别是在结构——波浪——海床动力相互作用下对波压力响应机理以及针对连续筒的研究，可为工程应用提供有价值的参考。     

Powder Deposition in Three Parallel-Oriented Dies of Different Shapes

Uniformity of bulk density distribution during the die filling process is required to minimize quality problems, such as distortion and cracking, for powder compacts. Understanding the die filling process is necessary in ensuring a uniform powder deposition. The second-generation pressure deposition tester (PDT-II) was used to investigate the deposition process and final pressure distribution of powder filling in toroidal, cylindrical, and E-shaped dies. All tests were conducted using a spray-dried free-flowing granular powder. The results indicated that for toroidal dies: (1) the area around 0° orientation (the leeward end) had the highest pressure values (1186.7 to 2498.0 Pa), with the average pressure values of the remaining area 353.7-648.0 Pa; (2) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; (3) the highest feed shoe speed (500 mm/s) led to the most nonuniform pressure distribution among the three speeds; (4) higher feed shoe speed did not always result in higher final pressure values; and (5) the right die tended to have higher final pressure values (215.0 to 2498.0 Pa) than the center die (95.4 to 2052.5 Pa). For E-shaped dies: (1) the final pressure values of the middle leg (308.9 to 760.7 Pa) were higher than those of the left and the right legs (148.9 to 530.3 Pa); (2) the area along the backside had the highest final pressure value (1054.6 to 1303.8 Pa); (3) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; and (4) neither the center die nor the right die always had higher pressure values than the other one at all locations. Comparison between cylindrical and toroidal dies indicated that: (1) neither of the two die shapes (cylinder and toroid) led to consistently higher or lower final pressure values at all locations and (2) for all three feed shoe speeds, the toroidal die had higher average final pressure values in the 0° orientation.     

螺旋翅片管的换热计算

本文引入区域平均表面传热系数的概念。在实验研究的基础上进行了肋基和肋端温度分布预测及肋片换热数值计算。     

用双向扭转圆柱组合螺旋弹簧实现扭矩测试

利用单个圆柱螺旋扭转弹簧扭转原理,给出了一种用双向扭转圆柱组合螺旋弹簧实现扭矩测试的方法。根据扭转弹簧模型,给出了预紧力、加载的证明,并对实验结果进行分析;该结构用于扭矩测试系统既实用可靠,又简单易加工;降低了测试系统的成本,具有很高的实用价值。     

Effects of Working Fluid,Tubeside Enhancement and Bundle Depth on the Optimized Fin Geometry of a Horizontal Condenser Tube

A theoretical study has been made to optimize the fin geometry of a horizontal finned tube which is to be usedfor condensers that handle the vapor load of a liquid phase change cooling module.Systematic numerical calcu-lations of the vapor to coolant heat transfer have been performed for parametric values of fin height,fin spacing,vertical bundle depth and tubeside heat transfer coefficient.Three dielectric fluids (R-113,FC-72,and FC-87)at atmospheric pressure were selected as the working fluids.For a single tube with optimized fin geometry,theaverage heat flux increased in the order of FC-87,R-113 and FC-72.Both the optimum fin height and optimumfin spacing increased with increasing vertical bundle depth.     

翅片式空气冷却器改造

针对茂名石化乙烯工业公司全密度聚乙烯装置翅片式空气冷却器存在的问题。结合生产实际要求进行了改造。将原设备换热芯由不可拆结构改为可抽芯结构。原圆形换热管更换为椭圆管。材质由SS304不锈钢更换为铜，并对改造后的空气冷却器进行了传热核算。理论和实践证明，改造是成功的。     

筒形件反旋工艺塑性流动刚塑性有限元分析

建立了筒形件反旋工艺平面变形刚塑性有限元分析的力学模型，比较了把反旋工艺视为正挤和本文力学模型条件下的速度场，有限元分析结果与反旋实际条件相符。     

Speed-of-sound measurements in liquid and gaseous air

The speed of sound in air has been measured along isotherms for a standard air mixture (0.7811 N₂+0.2097 O₂+0.0092 Ar) in the gas and liquid phases at pressures to 14 MPa. A cylindrical resonator was used in the vapor and supercritical gas phases, and a time-of-flight system was used for measurements of the liquid phase. Data were obtained for the liquid phase at 90, 100, 110, 120, and 130 K. Data were taken at 110, 120, 130, 135, 140, 150, 200, and 300 K in the vapor and supercritical gas phases. These experimental results were compared to a predictive computer model, namely, AIRPROPS.     

用圆柱铣刀加工带冠弯扭叶片

本文把微分几何中曲线与曲面之间的“切触”概念应用于叶片复杂曲面的数控加工，提出用圆柱铣刀的外圆在五坐标联动中加工小曲率曲面的最佳切触条件。