Synthesis and performance evaluation of a new drag reducer based on acrylamide/12-allyloxydodecyl acid sodium

Hydraulic fracturing with slickwater is a field-proven stimulation technology used in tight reservoirs. Because of the high pumping rate associated with slickwater fracturing, drag reduction (DR) is critical in minimizing pressure drop and the success of oilfield operations. In this paper, a new type of drag reducer (SPR) was synthesized with acrylamide and 12-allyloxydodecyl acid sodium, and its drag reduction performance was evaluated. The results showed that the new drag reducer features low molecular weight, fast-dissolving rate and low interfacial tension. The algorithm of estimating the drag reduction rate of non-Newtonian fluid SPR was proposed and validated. Empirical or semianalytical models for estimating the friction ratio (σ) or friction factor (λ or f) were used to simulate the turbulence behavior of the SPR drag reducer under different Reynolds numbers (Re). The modified Virk's correlation could accurately model the turbulent behavior of the SPR drag reducer. A unified calculation formula was established in this study for different pipe diameters.     

喷油方式对斜齿轮齿面温度的影响

为探讨喷油方式对齿面温度的影响，以斜齿轮为研究对象，通过CFD仿真和试验研究不同喷油方式对斜齿轮齿面温度的影响。针对斜齿轮喷油润滑过程的特点，分析其齿面摩擦生热量，简化轮齿喷油润滑计算模型，并基于CFX进行齿面对流换热仿真研究，得到了不同喷油方式下的齿面温度；基于功率开放式斜齿轮试验平台，对不同喷油方式下的齿面温度进行了试验测量，与仿真计算结果进行对比分析。结果表明：在高速重载斜齿轮传动系统中，啮出侧喷油润滑的方式比啮入侧喷油润滑方式的冷却降温效果要好。     

信号的小波尺度-频率表示及其在机械故障诊断中的应用

基于对信号的连续小波变换特点的分析，提出信号特征的小波尺度一频率表示方法。该方法对污染的脉冲信号和正弦信号的应用结果表明该方法能有效提取强噪声背景下的周期成分。以变速器齿轮的故障诊断为例，用该方法对变速箱齿轮振动信号的尺度-频率表示进行分析，结果表明该方法能非常有效地将不同磨损状况的齿轮振动信号的特征表现出来。     

双相活齿泵的工作原理

在活齿传动理论及齿轮泵工作原理相结合的基础上，介绍了双相活齿泵的结构及其工作原理，研究结果表明，双相活齿泵具有流量大、流量均匀性好、噪声低以及可变量等优点。     

DXDK800自动充填包装机料袋长度的调整

本文主要介绍了在DXDK800自动充填包装机中 ,采用一种新型的齿轮—蜗轮、蜗杆差速器来对膜片的进给速度进行微量的调整。及采用一种新型的可调式偏心链轮来调整横封辊的瞬时线速度 ,使其与料袋膜的进给速度相一致     

Eigenspannungen als Messgröße zur Qualitätssicherung

Residual stress as measured quantity in quality assurance The x‐ray method is used in the Volkswagen Automotive Group at different world‐wide locations as a standard procedure to determine residual stress. As an important measured quantity in the quality assurance residual stresses are specified in drawings of different components (e.g. gears, coil springs). Measurements are carried out during quality assurance, production, damage analyse, technical development department and design control of components from suppliers. An optimum efficiency can be achieved, if it exists a unique correlation between residual stress values and loading capacity of components, and if the processes to introduce residual stress can be optimized using residual stress measurements during the production.     

连轧机用人字轮齿轴断裂失效分析

用宏观断口分析、化学检验、力学性能测定、低倍检查、金相组织及夹杂物评定鉴别、受力分析及强度寿命定量估算的方法，对人字轮被动齿轴端断裂失效原因进行分析，并提出改进措施。     

齿轮磨前滚刀的齿形研究

本文介绍了磨前滚刀滚切齿轮的最大根切量和磨后的渐开线长度计算,并建立了数学模型。为更加直观起见,还建立了模拟滚齿的数学模型。并在实验的基础上提出了参考标准。     

抽油机减速器齿轮的失效分析

找出了人字齿轮减速器在工作中右端齿轮出现严重磨损的原因并进行了分析。提出在国内现有制造技术的条件下，对于37kN·m以下的减速器应推广使用斜齿轮传动。     

内外齿复合冷挤压成型实验研究

通过对轿车转向盘毂件内外齿进行的复合挤压实验研究 ,得到了新式复动式复合挤压模具结构 ,并确定了一种合理的成型工艺方案