排风扇前盖注射模设计

分析了排风扇前盖塑件的工艺特点,介绍了排风扇前盖注射成型模结构及模具的工作过程。     

阻尼胶囊的生产工艺研究

通过对胶料配方、工艺规程、模具结构的试验研究，成功地解决了胶囊制造过程中的难点问题。     

Viscosity estimation for slags containing calcium fluoride

Based on recently published experimental data, the Riboud model was modified for viscosity estimation of the slags containing calcium fluoride. The estimated values were in good agreement with measured data. Reasonable estimation can be achieved using the modified Riboud model for mould fluxes and ESR (eletro slag remelting) slags. Especially for ESR slags, the modified Riboud model can provide much more precise values than the original Riboud model.     

书立复合冲裁模的设计

介绍了安装在液压试验机上的一种集冲裁、切口作用于一体的复合冲裁模的设计，解决了没有压力机的情况下冲裁件的加工问题。     

冷成型模具低温锌系磷化

研制出适用于冷成型模具高硬度表面的低温锌系磷化工艺。其中磷化液含Zn(H2 PO4 ) 2 ·2H2 O 6 0g/L ,Zn(NO3) 2 ·6H2 O 90g/L ,NaNO2 1.5g/L ,稀土促进剂 0～ 1.0g/L ,游离酸度 4～ 6点 ,总酸度 70～ 75点。该磷化液在 4 0℃下 ,处理 30～ 4 0min后可获得厚约 10 μm的磷化膜。性能测试表明 ,其减摩、润滑性能良好 ,摩擦系数约降 0 .1,与未处理试样相比磨损量下降 96 % ,附着力 1级。     

Li2O在保护渣中的作用

采用在不同玻璃性的两种基渣中加入Ｌｉ２Ｏ为研究Ｌｉ２Ｏ对保护渣粘度，熔化温度及玻璃性能的影响，并对Ｌｉ２Ｏ改善保护渣玻璃性的机理进行了探讨，提出了寻找高速连铸保护渣中Ｌｉ２Ｏ的代用物的一种方法。     

High-efficiency finishing process for metal mold by large-area electron beam irradiation

A new finishing process for metal molds by large-area electron beam (EB) irradiation is proposed in this study. In the large-area EB irradiation equipment used here, an EB with high-energy density is irradiated without focusing the beam, and so the EB with a maximum diameter of 60 mm can be used for melting or evaporating metal surface instantly. Experimental results show that the surface roughness decreases from 6 μmRz to less than 1 μmRz in just a few minutes under proper machining conditions. The corrosion resistance of metal mold surface also could be greatly improved by large-area EB irradiation. Furthermore, the surface roughness of tilting surface close to 90° could be well improved. Therefore, large-area EB irradiation method has a possibility to become a high-efficiency finishing process for metal molds.     

结晶器液面自动控制系统在唐钢板坯连铸机的应用

介绍了涡流法和同位素法2种结晶器钢水液面自动控制检测方式,及其在唐钢板坯连铸机的应用.     

优化SMC模压工艺控制制品收缩率和表面粗糙度

优化SMC模压工艺参数：模压压力分为二阶段，选定最佳压力释放时机和压力；适宜降低模压温度。可显著降低SMC制品的固化收缩率，提高其表观质量、试验表明，同时采用的线收缩率和表面粗糙度两种检测和村定方法具有很好的同一性。