Long multifilament Bi-2223 Ag-sheathed superconducting tapes and solenoids

Multifilament Ag-sheathed BiPbSrCaCuO (2223) superconducting tapes containing 49 filaments were fabricated by the powder-in-tube route and the roll-anneal process. The transport critical current densityJ _c was 1.3×10⁴ A cm^–2 at 77 K and 7×10⁴ A cm^–2 at 4.2 K in self-field. A 12-m-long tape was used to construct superconducting solenoids (50, 28, and 14 mm internal diameters) generating dc fields 380–1070 G at 4.2 K. Measurements of the variation ofJ _c with field (0–1.6 T) and bend strain (0–5%) are used to explain the performance of the solenoids. The critical bend strain of tapes was about 1.5%.     

工艺因素对金属封装外引线弯曲疲劳的影响

考察了金属封装外壳制造工艺对外引线弯曲疲劳的影响,发现电镀镍是导致外引线弯曲次数明显减少的最主要工艺步骤,且随镀镍层厚度的增加,弯曲次数减少。此外还讨论了外引线的氢含量和晶粒度对引线抗疲劳能力的影响。     

冷轧带肋钢筋直径与拉丝机卷筒直径的匹配

采用被动式工艺生产冷轧带肋钢筋须经过减径、成型两台轧机连续轧制．要求钢材的秒流量相等，否则将造成断线停产或线材在拉丝机卷筒上打滑，致使卷筒严重磨损．用双层卷筒拉丝机提供动力生产冷轧带肋钢筋时，线材直径与卷筒直径的匹配是在一个小的调整范围，通过轧机拉力控制在一定范围变化，可保证成品尺寸符合公差要求而不产生打滑，从而避免了卷筒严重磨损．     

某铁路医院加速器室大体积防射线混凝土施工

结合大同铁路分局中心医院直线加速器室工程实际，介绍了大体积防射线混凝土的特点及施工中应注意的事项，并阐述了具体的施工技术。     

Analysis and Simulation of S-shaped Waveguide in Silicon-on-insulator

The simulation and analysis of S-shaped waveguide bend are presented.Bend radius larger than 30 mm assures less than 0.5 dB radiation loss for a 4-μm-wide silicon-on-insulator waveguide bend with 2-μm etch depth.Intersection angle greater than 20° provides negligible crosstalk (<-30 dB) and very low insertion loss.Any reduction in bend radius and intersection angle is at the cost of the degradation of characteristics of bent waveguide and intersecting waveguide, respectively.     

A Mixed-Approach Analysis of Deformations in Pipe Bends. Part 3. Calculation of Bend Axis Displacements by the Method of Initial Parameters

A problem of deformation of a curved shell loaded by internal pressure, axial force, and temperature difference is discussed. Physical equations are derived whereby the displacements and angles of rotation of the line of centers of mass of cross sections of a shell are related to loading parameters. A general constitutive set of equations for a curved element during its deformation is given. Using a method of initial parameters, an analytical solution is obtained for the differential equations for displacements and angles of rotation of the center line allowing for the action of distributed forces and moments.     

含V、N无缝钢管表面外折缺陷产生原因的分析

通过对鞍钢生产的部分批号V、N微合金强化无缝钢管及生产该钢管的原料连铸坯和连轧管坯的表面缺陷进行研究，分析了含V、N钢管表面外折缺陷的成因，提出了改善钢管表面质量的方法。采用改进后工艺生产的无缝管，其表面外折废品量大幅度降低。     

无线电引信被干扰率及抗干扰率

本文从无线电引信相对杀伤比率出发，引伸出引信被干扰率及抗干扰率的定义及计算公式。     

热轧带肋钢筋屈服不明显原因分析与探讨

针对涟钢热轧带肋钢筋的屈服不明显现象，从金属的金相组织、人工时效、自然时效、测试方法等方面着手，寻求各因素对钢筋力学性能的影响，并阐述了该异常组织的形成机理及相关因素，指出魏氏体、粒状贝氏体等的存在是造成带肋钢筋性能异常的主要原因，同时对部分屈服不明显的带肋钢筋判定提供了较为科学的依据。     

Stress State of Bent Buried Pipelines

The authors consider edge effects in buried pipelines that occur in the region of joining of a straight buried pipe and a bent insert (factory bend, elbow, or an elastically bent segment). The action of those effects results in the appearance of additional bending moments, which are proportional to the difference between the axial force in an infinite straight pipeline and that in a closed-end pipe, and depend on the geometrical parameters of the pipeline and physical-mechanical characteristics of the soil. Specific examples of analysis of elastic interaction of a pipeline with the soil for pipe bends with various radii of the bend arc are offered. It is shown that additional bending stresses may exceed appreciably the stresses from the axial force, and therefore, they should be taken into account when designing and building pipelines. The solution for an elastically bent segment has been obtained and analyzed.