轧机主传动万向联轴器辊端接头结构探讨

分析了衬板槽平面与叉头十字轴孔轴线的相对位置对辊端接头应力的影响 ,研究了轧辊扁头与衬板之间间隙所产生的冲击和应力集中 ,讨论了辊端接头中部过渡段结构对应力分布和制造质量的影响。提出辊端接头结构设计的优化方案     

纤维混凝土在水工建筑工程中的应用(上)

概述改性混凝土垢发展情况，介绍纤维混凝土在国内外水工建筑物上的应用实例，提出钢纤维增强钢筋混凝土水工建筑结构强度计算方法。包括受弯构件正截面强度，斜截面抗剪强度的计算；重点介绍了网状钢纤维增强混凝土（FOC）在水工建筑物上的应用，包括在渡槽，闸门，小型拦河坝，轻型岸型等工程上的应用实例，T新梁正斜截面的强度计算，板材承载力计算的方法。     

对称配筋小偏心受压构件的截面设计

对小偏心受压构件在对称配筋情况下的截面配筋计算，提出用最佳一次逼近多项式简化基本公式，直接按二次方程求解ξ的近似方法，具有精度高，相对误差小，计算方便等优点，可供工程设计人员参考。     

新型刮刀钻头的设计及现场试验研究

在理论分析的基础上，综合PDC钻头和刮刀钻头的优点，设计了一种新型的刮刀钻头，并进行了现场试验。现场试验结果表明，该钻头运转平稳，采用低钻压、高转速，钻进速度快，井眼规则通畅，有较明显的防斜作用，该种钻头的推广应用对提高钻井工程的整体效益具有十分重要的意义。     

影响混凝土强度的因素及控制措施

分析了水泥强度等级、水灰比和骨料质量等内因,及施工条件、养护温度、湿度、龄期等外因对混凝土强度的影响,并提出了控制混凝土强度的相应措施,以确保混凝土强度符合设计及施工要求,从而保证建筑物结构安全。     

某铁路医院加速器室大体积防射线混凝土施工

结合大同铁路分局中心医院直线加速器室工程实际，介绍了大体积防射线混凝土的特点及施工中应注意的事项，并阐述了具体的施工技术。     

定向爆破拆除框架式水塔

高 2 7m的水塔建于 193 4年 ,其顶部水罐由 12根钢筋混凝土柱支撑。在倒向侧 7根立柱上形成不同高度的爆破切口 ,背向侧倾倒中心线上的一根立柱上形成小爆破切口 ,其余 4根立柱底部打贯通孔 ,使水塔准确定向倾倒。文中讨论了立柱切口高度的计算 ,爆破参数的确定 ,并介绍了所采用的安全措施。     

针梁台车在大花水水电站引水隧洞混凝土衬砌施工中的改进

大花水水电站引水隧洞由于前期开挖工期略有滞后，为加快施工进度，结合全圆断面的施工特点，大部分引水隧洞采用了全圆针梁穿行式钢模台车进行混凝土衬砌。通过各参建单位对针梁台车的运用和改进，有效地提高了引水隧洞混凝土的衬砌速度，并确保了工程质量。     

Effect of specimen size and loading conditions on spalling of concrete

Different qualities of concrete have been fire tested using different geometries of the specimens as well as different load levels and load configurations. The main objective with the study was to examine a test methodology consisting of a full‐scale test and different small scale‐tests for determining the probability of spalling and the amount of spalling of fire exposed concrete structures. A reference specimen was defined as a one‐sided fire exposed slab with the dimensions 1800 × 1200 mm² giving an exposed area of 1500 × 1200 mm². A number of concrete qualities with different probabilities for spalling, were tested using the reference specimen. These tests showed that the reference specimens worked well giving the expected test results. Small specimens were manufactured in different shapes with the same concrete as the one used in the reference tests. These small specimens were tested either at the same time as the reference specimens in the large furnace or afterwards on a small‐scale furnace where the fire exposed surface was 450 × 360 mm². The test results clearly show the increased probability and the increased amount of spalling by using external compressive loading. The results also show that by using pre‐stress through bars or wires the load can be lost due to heating of the bars/wires which results in a decreased amount of spalling. The boundary of the specimen also affects the amount of spalling. The spalling around the edges was in all tests less than the spalling on the central parts of the exposed area. It could also be noted that the spalling did not pass completely through any of the specimens. The reason for this is probably that the water/vapour could migrate out from the unexposed surface of the specimen. Copyright © 2006 John Wiley & Sons, Ltd.     

A limit analysis of nonlinear elastic lateral displacements of thin-walled reinforced and prestressed beams

An incremental iterative process based on direct energy minimization is presented for a limit analysis of nonlinear elastic lateral displacements and twists of reinforced and prestressed beams. Problems encountered with the constitutive relations are discussed and two possible material models are presented.