鹤岗煤田新华勘探区主要煤层对比浅析

介绍了鹤岗煤田的地质概况 ,并对主要可采煤层的一些比较明显的特征进行了对比。     

松软厚煤层轻放工作面切眼锚杆支护实践

针对朱仙庄矿 84 15工作面切眼特殊的地质条件 ,介绍了高强锚杆 (索 )支护技术成功应用于特厚极软煤层的经验 ,并对巷道支护成本进行了分析     

Life Calculations for Header – PGV-1000 Steam Generator Connector Weld Joints under NPP Service Conditions

The procedure for calculating the life of header – steam generator connector weld joints is proposed. It allows for running out the material plasticity reserve upon static cyclic elastoplastic loading as well as operating conditions, local stress concentrations, and residual stresses after welding.     

省煤器管开裂原因分析

对省煤器开裂管进行了化学成分及宏、微观分析。分析结果表明，在高温高压条件下，在其焊缝溶合区出现粗大的魏氏组织，管材中的珠光体组织产生了不同程度的球化，而母材组织又存在严重的带状组织。在过热条件下熔合区极易出现裂纹，并由此快速扩展，造成省煤器管开裂。     

焊接方法对双相不锈钢焊接接头力学性能的影响

研究了不同焊接方法对SAF2205双相不锈钢板焊接接头金相组织和力学性能的影响,结果表明,采用不同焊接方法得到的焊接接头的铁素体与奥氏体两相比例不同,使焊接接头的力学性能存在较大差异,对实际生产中SAF2205双相不锈钢的焊接具有一定的指导意义。     

新一代高强韧性WDL系列钢综合性能及应用

本文着重介绍武汉钢铁公司近年来研制开发的第二代高强度低合金钢—高强韧性WDL系列钢的综合性能及应用情况。该钢具有优异的焊接性能和低温韧性,板厚≤50mm钢板焊前不预热或稍加预热而不产生焊接裂纹,是制造大型压力容器（特别是低温和常温球罐）、水电站压力钢管和水轮机蜗壳、高寒地区使用的大型工程机械、大跨度桥梁及海上采油平台等装备的理想用材。     

10000m^3天然气球罐用WEL—TEN610CF钢焊接冷裂纹敏感性

WEL-TEN610CF钢是日本新日铁公司生产的低裂纹敏感性高强钢,结合我国首台国产化10 000 m3天然气球罐用37 mm厚WEL-TEN610CF钢焊接性试验研究,对该钢焊接冷裂纹敏感性进行了综合评定,为其焊接工艺的制订提供了可靠的依据。     

Metallurgical failure analysis of cold cracking in a structural steel weldment: Revisiting a classic failure mechanism

Cold cracking of structural steel weldments is a well-characterized, well-documented, and well-understood failure mechanism. Extensive effort has been put forth to recognize the welding and materials selection parameters that are conducive to cold cracking; however, these engineering efforts have not fully eliminated the occurrence of such failures. This article describes cold cracking failure specifically related to the construction industry. This particular failure was successfully identified prior to final erection of the structural member, and the weld was successfully reworked. These actions potentially prevented a serious catastrophic event that could have occurred have occurred either later in the construction process or possibly during the use of the building. Individual welding parameters, such as electrode/wire selection, joint design, and pre/postheating, played a role in the failure, and a number of human factors relating to the actual fabrication practices also contributed to the failure process.     

国内外厚煤层大功率电牵引采煤机机电一体化新技术

介绍国内外大功率厚煤层电牵引采煤机的机电一体化新技术,包括总体技术、交流变频电牵引技术、工况检测、故障诊断技术、自动调高技术、远程通讯和集中控制技术。     

近距离下覆4#煤层综采工作面顶板管理经验

介绍了近距离深层综采工作面顶板和巷道顶板管理经验，及综采工作面在通过巷道冒项区域时所采取的办法和措施。